LEMON Manuals: Even more car manuals for everyone
Home >> Lexus >> 2020 >> ES 300h Luxury >> Repair and Diagnosis >> External Pages >> Different car >> Section 173 (Electronically Controlled Brake System (Except Hybrid) - Diagnostic Codes (1 Of 4)) >> ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model) >> DTC C0506-1F: Right Front Wheel Speed Sensor Circuit Intermittent [06/2018 - ] >> Procedure

DTC C0506-1F: Right Front Wheel Speed Sensor Circuit Intermittent [06/2018 - ]: Procedure

WARNING: This page does not describe the selected car, but rather 10 other vehicles, including the 2024 Lexus ES 350, 2024 Lexus ES 250, 2023 Lexus ES 350, 2023 Lexus ES 250, and 2022 Lexus ES 350. However, it is still accessible from the selected car via links, so may be relevant.
  1. CHECK FRONT SPEED SENSOR RH (CHECK FOR FOREIGN MATTER) 
    1. Remove the front speed sensor RH.

      Refer to REMOVAL [06/2018 - 08/2020] , or refer to REMOVAL [08/2020 - ]

    2. Check the front speed sensor RH.

      OK

      The front speed sensor RH tip is free of oil and foreign matter.

      HINT: 

      If foreign matter of 1mm x 1mm or more is adhered to the front speed sensor RH, this DTC may be stored.

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    See step  7

    Result: 

    OK 

    See step  2

  2. CHECK FRONT SPEED SENSOR ROTOR RH (CHECK FOR FOREIGN MATTER) 
    1. Remove the component with the front speed sensor rotor RH.

      Refer to REMOVAL [06/2018 - 08/2020] , or refer to REMOVAL [08/2020 - 08/2021] , or refer to REMOVAL [08/2021 - 09/2022] , or refer to REMOVAL [09/2022 - ]

    2. Check the front speed sensor rotor RH.

      OK

      The front speed sensor rotor RH is free of oil and foreign matter.

      HINT: 

      If foreign matter of 1mm x 1mm or more is adhered to the front speed sensor rotor RH, this DTC may be stored.

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE FRONT SPEED SENSOR RH AND FRONT AXLE HUB SUB-ASSEMBLY RH 

    for front speed sensor RH: Refer to REMOVAL [06/2018 - 08/2020] , or refer to REMOVAL [08/2020 - ]

    for front speed sensor rotor RH (front axle hub sub-assembly RH): Refer to REMOVAL [06/2018 - 08/2020] , or refer to REMOVAL [08/2020 - 08/2021] , or refer to REMOVAL [08/2021 - 09/2022] , or refer to REMOVAL [09/2022 - ]

    Result: 

    NG 

    See step  3

  3. CLEAN FRONT SPEED SENSOR ROTOR RH 
    1. Clean the front speed sensor rotor RH.
      NOTE:

      Do not use parts cleaner when cleaning the front speed sensor rotor RH.

      Result

      Proceed to
      NEXT

    Result: 

    NEXT 

    See step  4

  4. CLEAR DTC 
    1. Connect the Techstream to the DLC3.
    2. Turn the engine switch on (IG).
    3. Operate the Techstream to clear the codes. Enter the following menus: Chassis / Brake/EPB / Trouble Codes.

      Chassis > Brake/EPB > Clear DTCs 

    4. Press the DTC clear button.

      Result

      Proceed to
      NEXT

    Result: 

    NEXT 

    See step  5

  5. PERFORM DEALER MODE (SIGNAL CHECK) INSPECTION (SPEED SENSOR CHECK) 
    1. Connect the Techstream to the DLC3.
    2. Turn the engine switch on (IG).
    3. Using the Techstream, perform a Dealer Mode (Signal Check) inspection sensor check and check that speed sensor Dealer Mode (Signal Check) inspection items change from incomplete to complete. Enter the following menus: Chassis / Brake/EPB / Utility / Signal Check.

      Refer to TEST MODE PROCEDURE [06/2018 - 08/2020] , or refer to TEST MODE PROCEDURE [08/2020 - ]

      Chassis > Brake/EPB > Utility 

      Tester Display
      Signal Check

      OK

      Speed sensor Dealer Mode (Signal Check) inspection items change from incomplete to complete.

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPLACE FRONT SPEED SENSOR RH AND FRONT AXLE HUB SUB-ASSEMBLY RH 

    for front speed sensor RH: Refer to REMOVAL [06/2018 - 08/2020] , or refer to REMOVAL [08/2020 - ]

    for front speed sensor rotor RH (front axle hub sub-assembly RH): Refer to REMOVAL [06/2018 - 08/2020] , or refer to REMOVAL [08/2020 - 08/2021] , or refer to REMOVAL [08/2021 - 09/2022] , or refer to REMOVAL [09/2022 - ]

    Result: 

    OK 

    See step  6

  6. RECONFIRM DTC 
    1. Connect the Techstream to the DLC3.
    2. Start the engine.
    3. Perform a road test under the same malfunction conditions recreated based on the Freeze Frame Data or customer problem analysis.
    4. Read the DTCs following the prompts on the Techstream. Enter the following menus: Chassis / Brake/EPB / Trouble Codes.

      Chassis > Brake/EPB > Trouble Codes 

    5. Check if the same DTC is output.

      Result

      Result Proceed to
      C0506-1F is not output A
      C0506-1F is output B

    Result: 

    A 

    END 

    Result: 

    B 

    REPLACE FRONT SPEED SENSOR RH AND FRONT AXLE HUB SUB-ASSEMBLY RH 

    for front speed sensor RH: Refer to REMOVAL [06/2018 - 08/2020] , or refer to REMOVAL [08/2020 - ]

    for front speed sensor rotor RH (front axle hub sub-assembly RH): Refer to REMOVAL [06/2018 - 08/2020] , or refer to REMOVAL [08/2020 - 08/2021] , or refer to REMOVAL [08/2021 - 09/2022] , or refer to REMOVAL [09/2022 - ]

  7. CLEAN FRONT SPEED SENSOR RH 
    1. Clean the front speed sensor RH.
      NOTE:

      When cleaning the front speed sensor RH, make sure to clean the installation hole before installation.

      Result

      Proceed to
      NEXT

    Result: 

    NEXT 

    See step  8

  8. CLEAR DTC 
    1. Connect the Techstream to the DLC3.
    2. Turn the engine switch on (IG).
    3. Operate the Techstream to clear the codes. Enter the following menus: Chassis / Brake/EPB / Trouble Codes.

      Chassis > Brake/EPB > Clear DTCs 

    4. Press the DTC clear button.

      Result

      Proceed to
      NEXT

    Result: 

    NEXT 

    See step  9

  9. PERFORM DEALER MODE (SIGNAL CHECK) INSPECTION (SPEED SENSOR CHECK) 
    1. Connect the Techstream to the DLC3.
    2. Turn the engine switch on (IG).
    3. Using the Techstream, perform a Dealer Mode (Signal Check) inspection sensor check and check that speed sensor Dealer Mode (Signal Check) inspection items change from incomplete to complete. Enter the following menus: Chassis / Brake/EPB / Utility / Signal Check.

      Refer to TEST MODE PROCEDURE [06/2018 - 08/2020] , or refer to TEST MODE PROCEDURE [08/2020 - ]

      Chassis > Brake/EPB > Utility 

      Tester Display
      Signal Check

      OK

      Speed sensor Dealer Mode (Signal Check) inspection items change from incomplete to complete.

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    See step  2

    Result: 

    OK 

    See step  10

  10. RECONFIRM DTC 
    1. Connect the Techstream to the DLC3.
    2. Start the engine.
    3. Perform a road test under the same malfunction conditions recreated based on the Freeze Frame Data or customer problem analysis.
    4. Read the DTCs following the prompts on the Techstream. Enter the following menus: Chassis / Brake/EPB / Trouble Codes.

      Chassis > Brake/EPB > Trouble Codes 

    5. Check if the same DTC is output.

      Result

      Result Proceed to
      C0506-1F is not output A
      C0506-1F is output B

    Result: 

    A 

    END 

    Result: 

    B 

    See step  2

scientia non olet · About LEMON Manuals