DTC C0500-23: Left Front Wheel Speed Sensor Signal Stuck Low [06/2018 - ]: Procedure

1. Connect the Techstream to the DLC3.
2. Turn the engine switch on (IG).
3. Enter the following menus: Chassis / Brake/EPB / Trouble Codes.
4. Select a DTC to display the Freeze Frame Data.
5. Read the freeze frame data of DTC C0500-23.

   Chassis > Brake/EPB 

   Tester Display	Measurement Item	Range	Normal Condition	Diagnostic Note
   FR Wheel Speed	Front wheel speed sensor RH reading	Min.: 0.0 km/h (0 mph), Max.: 6553.5 km/h (4072 mph)	Vehicle stopped: 0.0 km/h (0.0 mph)	When driving at constant speed: No large fluctuations
   FL Wheel Speed	Front wheel speed sensor LH reading	Min.: 0.0 km/h (0 mph), Max.: 6553.5 km/h (4072 mph)	Vehicle stopped: 0.0 km/h (0.0 mph)	When driving at constant speed: No large fluctuations
   RR Wheel Speed	Rear wheel speed sensor RH reading	Min.: 0.0 km/h (0 mph), Max.: 6553.5 km/h (4072 mph)	Vehicle stopped: 0.0 km/h (0.0 mph)	When driving at constant speed: No large fluctuations
   RL Wheel Speed	Rear wheel speed sensor LH reading	Min.: 0.0 km/h (0 mph), Max.: 6553.5 km/h (4072 mph)	Vehicle stopped: 0.0 km/h (0.0 mph)	When driving at constant speed: No large fluctuations

   Chassis > Brake/EPB > DTC(C0500-23) > Freeze Frame Data 

   Tester Display
   FR Wheel Speed
   FL Wheel Speed
   RR Wheel Speed
   RL Wheel Speed

   Result

   Result	Proceed to
   The value of FL Wheel Speed is 2 km/h (1 mph) or less when all other values are 12 km/h (7 mph) or more.	A
   The value of FL Wheel Speed is 2 km/h (1 mph) or less when all other values are 50 km/h (31 mph) or more.	B

Result: 

B 

See step  3

Result: 

A 

See step  2

1. Connect the Techstream to the DLC3.
2. Turn the engine switch on (IG).
3. Enter the following menus: Chassis / Brake/EPB / Data List.

   Chassis > Brake/EPB > Data List 

   Tester Display	Measurement Item	Range	Normal Condition	Diagnostic Note
   FL Wheel Speed	Front wheel speed sensor LH reading	Min.: 0.0 km/h (0.0 mph), Max.: 6553.5 km/h (4072 mph)	Vehicle stopped: 0.0 km/h (0.0 mph)	When driving at constant speed: No large fluctuations

   Chassis > Brake/EPB > Data List 

   Tester Display
   FL Wheel Speed

4. Start the engine and perform a road test.
5. Check that the value of FL Wheel Speed changes in accordance with vehicle speed when accelerating from 0 km/h to 20 km/h (0 mph to 12 mph).

   OK

   The value of FL Wheel Speed changes in accordance with vehicle speed.

   HINT: 

   If the result of the road test is within the specified range, it is possible that this DTC was stored due to a particular situation such as brake drag, wheelspin or wheel lockup.

   Result

   Proceed to
   OK
   NG

Result: 

OK 

USE SIMULATION METHOD TO CHECK. Refer to  HOW TO PROCEED WITH TROUBLESHOOTING [06/2018 - ] 

Result: 

NG 

See step  3

1. Check the front speed sensor LH installation.

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   *1	Front Speed Sensor LH
   *a	Correct
   *b	Incorrect
   *c	8.5 N.m
   *d	No clearance

   OK

   There is no clearance between the front speed sensor LH and the steering knuckle LH.

   The installation bolt is tightened properly.

   Torque 

   8.5 N.m (87 kgf/cm, 75 in.lbf)

   Result

   Proceed to
   OK
   NG

Result: 

OK 

REPLACE FRONT SPEED SENSOR LH. Refer to  REMOVAL [06/2018 - 08/2020]  , or refer to  REMOVAL [08/2020 - ] 

Result: 

NG 

REINSTALL OR REPLACE FRONT SPEED SENSOR LH. Refer to  INSTALLATION [06/2018 - 08/2020]  , or refer to  INSTALLATION [08/2020 - ]