LEMON Manuals: Even more car manuals for everyone
Home >> Lexus >> 2020 >> ES 300h Luxury >> Repair and Diagnosis >> External Pages >> Different car >> Section 159 (Engine Mechanical System (2GR-FKS) - Service Information (3 Of 3)) >> Cylinder Head >> Disassembly [08/2021 - 09/2022] >> Procedure

Disassembly [08/2021 - 09/2022]: Procedure

WARNING: This page does not describe the selected car, but rather 6 other vehicles, including the 2024 Lexus ES 350, 2023 Lexus ES 350, 2022 Lexus ES 350, 2021 Lexus ES 350, and 2020 Lexus ES 350. However, it is still accessible from the selected car via links, so may be relevant.
  1. REMOVE INTAKE VALVE 
    1. Using SST and wooden blocks, compress the inner compression spring and remove the 6 valve spring retainer locks from the valve spring retainer.
      GTY652238Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Wooden Block
      • SST: 09202-70020 
        1. 09202-01010
        2. 09202-01020
      • SST: 09202-00021 

      HINT: 

      Arrange the removed parts in such a way that they can be reinstalled to their original locations.

    2. Remove the 6 valve spring retainers, 6 inner compression springs and 6 intake valves from the cylinder head LH.

      HINT: 

      Arrange the removed parts in such a way that they can be reinstalled to their original locations.

  2. REMOVE EXHAUST VALVE 
    1. Using SST and wooden blocks, compress the inner compression spring and remove the 6 valve spring retainer locks from the valve spring retainer.
      GTY645833Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Wooden Block
      • SST: 09202-70020 
        1. 09202-01010
        2. 09202-01020
      • SST: 09202-00021 

      HINT: 

      Arrange the removed parts in such a way that they can be reinstalled to their original locations.

    2. Remove the 6 valve spring retainers, 6 inner compression springs and 6 exhaust valves from the cylinder head LH.

      HINT: 

      Arrange the removed parts in such a way that they can be reinstalled to their original locations.

  3. REMOVE INTAKE VALVE STEM OIL SEAL 
    1. Using needle-nose pliers, remove the 6 intake valve stem oil seals from the intake valve guide bush.
      GTY653435Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  4. REMOVE EXHAUST VALVE STEM OIL SEAL 

    HINT: 

    Use the same procedure as for the intake side.

  5. REMOVE VALVE SPRING SEAT 
    1. Using compressed air and a Magnet Hand, remove the 12 valve spring seats by blowing air onto them from the cylinder head LH.
      GTY653448Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      HINT: 

      Arrange the removed parts in such a way that they can be reinstalled to their original locations.

  6. REMOVE NO. 1 STRAIGHT SCREW PLUG 
    NOTE:

    If coolant leaks from a No. 1 straight screw plug or a plug is corroded, replace it.

    1. Using a 10 mm hexagon socket wrench, remove the 2 No. 1 straight screw plugs and 2 water hole gaskets from the cylinder head LH.
      GTY653444Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  7. REMOVE NO. 2 STRAIGHT SCREW PLUG 
    NOTE:

    If coolant leaks from a No. 2 straight screw plug or a plug is corroded, replace it.

    1. Using a 14 mm hexagon wrench, remove the No. 2 straight screw plug and cylinder head screw plug gasket from the cylinder head LH.
      GTY681524Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  8. REMOVE NO. 3 STRAIGHT SCREW PLUG 
    NOTE:

    If coolant leaks from a No. 3 straight screw plug or a plug is corroded, replace it.

    1. Using a 10 mm hexagon socket wrench, remove the 4 No. 3 straight screw plugs and 4 cylinder head screw plug gaskets from the cylinder head LH.
      GTY653402Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
scientia non olet · About LEMON Manuals