LEMON Manuals: Even more car manuals for everyone
Home >> Lexus >> 2020 >> ES 300h Luxury >> Repair and Diagnosis >> External Pages >> Different car >> Section 157 (Automatic Transmission System (UA80E) - Service Information (2 Of 4)) >> Shift Lever >> Inspection [06/2018 - ] >> Procedure

Inspection [06/2018 - ]: Procedure

WARNING: This page does not describe the selected car, but rather 6 other vehicles, including the 2024 Lexus ES 350, 2023 Lexus ES 350, 2022 Lexus ES 350, 2021 Lexus ES 350, and 2020 Lexus ES 350. However, it is still accessible from the selected car via links, so may be relevant.
  1. INSPECT SHIFT LOCK CONTROL ECU 

    HINT: 

    If the results of the following inspections are as specified but a malfunction has occurred, replace the shift lock control unit assembly.

    1. Inspect wire harness:
      1. Disconnect the shift lock control ECU connector.
        GTY784866Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      2. Measure the voltage according to the value(s) in the table below.
        GTY751103Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
        *a Front view of wire harness connector
        (to Shift Lock Control ECU)

        Standard Voltage

        Tester Connection Condition Specified Condition
        5 (IG) - Body ground Engine switch on (IG) 11 to 14 V
        Engine switch off Below 1 V

        If the result is not as specified, repair or replace the shift lock control ECU wire harness.

      3. Measure the resistance according to the value(s) in the table below.
        GTY751102Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
        *a Front view of wire harness connector
        (to Shift Lock Control ECU)

        Standard Voltage

        Tester Connection Condition Specified Condition
        4 (STP) - Body ground Engine switch on (IG), brake pedal depressed 11 to 14 V
        Engine switch on (IG), brake pedal released Below 1 V

        If the result is not as specified, repair or replace the shift lock control ECU wire harness.

      4. Measure the resistance according to the value(s) in the table below.

        Standard Resistance

        Tester Connection Condition Specified Condition
        1 (E) - Body ground Always Below 1 Ω
        GTY496833Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
        *a Front view of wire harness connector
        (to Shift Lock Control ECU)

        If the result is not as specified, repair or replace the shift lock control ECU wire harness.

    2. Inspect shift lock solenoid:
      1. Disconnect the shift lock solenoid connector.
        GTY809703Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      2. Measure the resistance according to the value(s) in the table below.
        GTY617139Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
        *a Front view of wire harness connector
        (to Shift Lock Solenoid)

        Standard Resistance

        Tester Connection Condition Specified Condition
        4 (P) - 3 (E2) Shift lever in P 10 kΩ or higher
        Shift lever not in P Below 1 Ω

        If the result is not as specified, replace the shift lock control unit assembly.

      3. Measure the resistance according to the value(s) in the table below.
        GTY617138Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
        *a Front view of wire harness connector
        (to Shift Lock Solenoid)

        Standard Resistance

        Tester Connection Condition Specified Condition
        1 (SLS+) - 2 (SLS-) Always 112 Ω

        If the result is not as specified, replace the shift lock control unit assembly.

  2. INSPECT TRANSMISSION CONTROL SWITCH 
    1. Disconnect the transmission control switch connector.
      GTY784885Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      4 (IG) - 5 (S) Shift lever in S, "+" or "-" Below 1 Ω
      Shift lever not in S, "+" or "-" 10 kΩ or higher
      3 (SFTU) - 2 (E) Shift lever held in "+"
      (Up-shift)      		 Below 1 Ω
      Shift lever not held in "+"
      (Up-shift)      		 10 kΩ or higher
      1 (SFTD) - 2 (E) Shift lever held in "-"
      (Down-shift)      		 Below 1 Ω
      Shift lever not held in "-"
      (Down-shift)      		 10 kΩ or higher

      If the result is not as specified, replace the shift lock control unit assembly.

      GTY836222Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Component without harness connected
      (Transmission Control Switch (Transmission Floor Shift Assembly))
scientia non olet · About LEMON Manuals