LEMON Manuals: Even more car manuals for everyone
Home >> Lexus >> 2020 >> ES 300h Luxury >> Repair and Diagnosis >> External Pages >> Different car >> Section 129 (Fuel System (2GR-FKS) - Service Information) >> FUEL INJECTOR (for Port Injection) >> Removal [06/2018 - 08/2021] >> Procedure

Removal [06/2018 - 08/2021]: Procedure

WARNING: This page does not describe the selected car, but rather 6 other vehicles, including the 2024 Lexus ES 350, 2023 Lexus ES 350, 2022 Lexus ES 350, 2021 Lexus ES 350, and 2020 Lexus ES 350. However, it is still accessible from the selected car via links, so may be relevant.
  1. PRECAUTION 
    NOTE:

    After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

  2. DISCHARGE FUEL SYSTEM PRESSURE 

    Refer to PRECAUTION [06/2018 - ]

  3. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL 

    Refer to PROCEDURE - Step 1

  4. REMOVE INTAKE AIR SURGE TANK ASSEMBLY 

    Refer to REMOVAL [06/2018 - 08/2021]

  5. DISCONNECT FUEL TUBE SUB-ASSEMBLY 
    1. Disconnect the fuel tube sub-assembly from the fuel delivery pipe with sensor assembly.
      GTY763752Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      Refer to PRECAUTION [06/2018 - ]

  6. REMOVE FUEL DELIVERY PIPE WITH SENSOR ASSEMBLY 
    1. Disconnect the fuel pressure sensor connector.
      GTY743615Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Fuel Pressure Sensor Connector
      *b No. 5 Engine Wire Connector
    2. Disconnect the 2 No. 5 engine wire connectors.
    3. Remove the 4 bolts and fuel delivery pipe with sensor assembly with the 6 port fuel injector assemblies from the intake manifold.
      GTY669054Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      NOTE:
      • If fuel intrudes into the combustion chamber, there may be adverse affects to the engine main body.
      • Be careful not to drop the port fuel injector assemblies when removing the fuel delivery pipe with sensor assembly.
      • When removing the fuel delivery pipe with sensor assembly, hold the pipe by both ends and pull it straight upward.
  7. REMOVE NO. 1 DELIVERY PIPE SPACER 
    1. Remove the 4 No. 1 delivery pipe spacers from the intake manifold.
      GTY763750Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  8. REMOVE INJECTOR VIBRATION INSULATOR 
    1. Remove the 6 injector vibration insulators from the intake manifold.
      GTY763751Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  9. REMOVE PORT FUEL INJECTOR ASSEMBLY 
    1. for Bank 2:
      1. Disengage the clamp to disconnect the No. 5 engine wire from the fuel delivery pipe with sensor assembly.
        GTY684977Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      2. Pull the 3 port fuel injector assemblies out of the fuel delivery pipe with sensor assembly.
      3. Disconnect the 3 port fuel injector assembly connectors.
        GTY669049Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. for Bank 1:
      1. Disengage the clamp to disconnect the No. 5 engine wire from the fuel delivery pipe with sensor assembly.
        GTY669048Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      2. Pull the 3 port fuel injector assemblies out of the fuel delivery pipe with sensor assembly.
      3. Disconnect the 3 port fuel injector assembly connectors.
        GTY669046Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. Remove the O-ring from each port fuel injector assembly.
    4. Attach a tag or label with the corresponding cylinder number to each port fuel injector assembly so that they can be installed to their original locations.
      NOTE:

      Cover the port fuel injector assemblies with plastic bags to prevent damage and contamination.

      GTY651227Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
scientia non olet · About LEMON Manuals