Tilt and Telescopic Manual Switch Circuit [06/2018 - ]: Procedure

1. Turn the engine switch off.
2. Connect the Techstream to the DLC3.
3. Turn the engine switch on (IG).
4. Turn the Techstream on.
5. Read the Data List according to the display on the Techstream.

   Body Electrical > Tilt&Telescopic > Data List 

   Tester Display
   Tilt Manual Switch Up
   Tilt Manual Switch Down
   Telescopic Manual Switch Short
   Telescopic Manual Switch Long

   Body Electrical > Tilt&Telescopic > Data List 

   Tester Display	Measurement Item	Range	Normal Condition	Diagnostic Note
   Tilt Manual Switch Up	Input state of tilt up switch	OFF or ON	-	-
   Tilt Manual Switch Down	Input state of tilt down switch	OFF or ON	-	-
   Telescopic Manual Switch Short	Input state of telescopic contract switch	OFF or ON	-	-
   Telescopic Manual Switch Long	Input state of telescopic extend switch	OFF or ON	-	-

   OK

   The value of each Data List item changes in accordance with the operation of the switch.

   Result

   Proceed to
   OK
   NG

Result: 

OK 

REPLACE MULTIPLEX TILT AND TELESCOPIC ECU. Refer to  REMOVAL [06/2018 - ] 

Result: 

NG 

See step  2

1. Disconnect the G63 multiplex tilt and telescopic ECU connector.
2. Disconnect the G31 tilt and telescopic switch connector.
3. Measure the resistance according to the value(s) in the table below.

   Standard Resistance

   Tester Connection	Condition	Specified Condition
   G63-5 (VC) - G31-1 (VC)	Always	Below 1 Ω
   G63-18 (MSW) - G31-3 (MSW)	Always	Below 1 Ω
   G63-5 (VC) or G31-1 (VC) - Body ground	Always	10 kΩ or higher
   G63-18 (MSW) or G31-3 (MSW) - Body ground	Always	10 kΩ or higher

   Result

   Proceed to
   OK
   NG

Result: 

NG 

REPAIR OR REPLACE HARNESS OR CONNECTOR 

Result: 

OK 

See step  3

1. Reconnect the G63 multiplex tilt and telescopic ECU connector.

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   *a	Component with harness connected (Multiplex Tilt and Telescopic ECU)

2. Measure the voltage according to the value(s) in the table below.

   Standard Voltage

   Tester Connection	Condition	Specified Condition
   G63-5 (VC) - G63-18 (MSW)	Engine switch on (IG)	4.9 to 5.1 V

   Result

   Proceed to
   OK
   NG

Result: 

NG 

REPLACE MULTIPLEX TILT AND TELESCOPIC ECU. Refer to  REMOVAL [06/2018 - ] 

Result: 

OK 

See step  4

1. Remove the tilt and telescopic switch.

   Refer to REMOVAL [06/2018 - 08/2020] , or refer to REMOVAL [08/2020 - 08/2021] , or refer to REMOVAL [08/2021 - 09/2022] , or refer to REMOVAL [09/2022 - ]

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   *a	Component without harness connected (Tilt and Telescopic Switch)

2. Measure the resistance according to the value(s) in the table below.

   Standard Resistance

   Tester Connection	Condition	Specified Condition
   G31-1 (VC) - G31-3 (MSW)	Tilt up	342 to 378 Ω
   	Tilt down	1890.5 to 2089.5 Ω
   	Telescopic contract	750.5 to 829.5 Ω
   	Telescopic extend	152 to 168 Ω

   Result

   Proceed to
   OK
   NG

Result: 

OK 

REPLACE MULTIPLEX TILT AND TELESCOPIC ECU. Refer to  REMOVAL [06/2018 - ] 

Result: 

NG 

REPLACE TILT AND TELESCOPIC SWITCH. Refer to  REMOVAL [06/2018 - 08/2020]  , or refer to  REMOVAL [08/2020 - 08/2021]  , or refer to  REMOVAL [08/2021 - 09/2022]  , or refer to  REMOVAL [09/2022 - ]