LEMON Manuals: Even more car manuals for everyone
Home >> Lexus >> 2019 >> UX 200 Base >> Repair and Diagnosis >> Accessories & Equipment >> Gauges & Instrument Panels >> (Meter / Gauge / Display) (Diagnostic Codes & Circuit Tests) >> (Meter / Gauge System) >> On-Vehicle Inspection [10/2018 - 07/2022] >> Procedure

On-Vehicle Inspection [10/2018 - 07/2022]: Procedure

  1. INSPECT COMBINATION METER ASSEMBLY 
    1. Inspect speedometer operation
      NOTE:
      • The combination meter assembly receives the vehicle speed signal from the skid control ECU (brake booster with master cylinder assembly) via CAN communication. Therefore, perform the following inspection referring to values on the Data List of the skid control ECU (brake booster with master cylinder assembly) because it is the source of the vehicle speed signal.*1
      • The combination meter assembly receives the vehicle speed signal from the skid control ECU (brake actuator assembly) via CAN communication. Therefore, perform the following inspection referring to values on the Data List of the skid control ECU (brake actuator assembly) because it is the source of the vehicle speed signal.*2
      • Data List values of the skid control ECU (brake booster with master cylinder assembly) are used for this inspection. Therefore, make sure to perform this inspection after confirming that DTCs are not output.*1
      • Data List values of the skid control ECU (Brake actuator assembly) are used for this inspection. Therefore, make sure to perform this inspection after confirming that DTCs are not output.*2
        1. *1: for HV Model
        2. *2: for Gasoline Model
      1. Warm up and stop the engine.
      2. Connect the Techstream to the DLC3.
      3. Turn the ignition switch to ON.
      4. Enter the following menus: Chassis / ABS/VSC/TRAC/ Data List.
      5. Read the Data List according to the display on the Techstream.
        1. for HV Model:

        Chassis > ABS/VSC/TRAC > Data List 

        Tester Display Measurement Item Range Normal Condition Diagnostic Note
        Vehicle Speed Maximum wheel speed sensor Min.: 0 km/h (0 mph), Max.: 326.4 km/h (203 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations

        Chassis > ABS/VSC/TRAC > Data List 

        Tester Display
        Vehicle Speed
        1. for Gasoline Model:

        Chassis > Brake/EPB > Data List 

        Tester Display Measurement Item Range Normal Condition Diagnostic Note
        Vehicle Speed Vehicle speed (vehicle speed used for each control) Min.: 0.0 km/h (0 mph), Max.: 6553.5 km/h (4072 mph) Vehicle stopped: 0.0 km/h (0.0 mph) When driving at constant speed: No large fluctuations

        Chassis > Brake/EPB > Data List 

        Tester Display
        Vehicle Speed
        REFERENCE MPH

        Techstream Indication (mph) Acceptable Range (mph)
        20 19.4 to 21.9
        40 39.8 to 42.6
        60 60.5 to 63.3
        80 80.9 to 84.1
        100 101.5 to 104.7
        120 122.1 to 125.3
        140 142.7 to 145.9
        REFERENCE KM/H

        Techstream Indication (km/h) Acceptable Range (km/h)
        20 18.6 to 22.6
        40 39.0 to 43.5
        60 59.7 to 64.2
        80 80.0 to 85.0
        100 100.6 to 105.6
        120 121.2 to 126.2
        140 141.8 to 146.8
        160 162.5 to 167.5
        180 183.1 to 188.1
        200 203.7 to 208.7
        220 224.3 to 229.3
        240 244.9 to 249.9

        OK

        Speedometer reading is within the acceptable range at each vehicle speed.

    2. Inspect tachometer operation
      1. Warm up the engine.
      2. Connect the Techstream to the DLC3.
      3. Turn the ignition switch to ON.
      4. Enter the following menus: Body Electrical / Combination Meter / Data List.
      5. Read the Data List according to the display on the Techstream.

        Body Electrical > Combination Meter > Data List 

        Tester Display Measurement Item Range Normal Condition Diagnostic Note
        Engine RPM Engine speed Min.: 0 rpm, Max.: 12701 rpm or Unset Almost the same as actual tachometer -

        Body Electrical > Combination Meter > Data List 

        Tester Display
        Engine RPM
        REFERENCE

        Techstream Indication (rpm) Acceptable Range (rpm)
        Data in () is for Reference
        700 630 to 770
        1000 (900 to 1100)
        2000 (1850 to 2150)
        3000 2800 to 3200
        4000 (3800 to 4200)
        5000 4800 to 5200
        6000 (5750 to 6250)
        7000 6700 to 7300

        OK

        Tachometer reading is within the acceptable range at each engine speed.

    3. Check warning or indicator light illumination (Initial check)
      1. Turn the ignition switch to ON from off, and check the operation of the warning and indicator lights in the following table.

        OK

        Warning or Indicator Light
        EPS warning light
        Slip indicator light
        PCS warning light
        VSC OFF indicator light
        PKSB OFF indicator light*1
        Brake warning light / yellow (minor malfunction)
        ABS warning light
        Brake warning light / red (malfunction)
        SRS warning light
        Brake hold operated indicator light
        BSM indicator light*2
        MIL (Check engine warning light)
        Tire pressure warning light
        Stop and start off indicator light*3*4
        Stop and start indicator light*3*4
        Automatic high beam indicator light
        Eco driving indicator light*4*5
        1. *1: w/ Parking Support Brake System
        2. *2: w/ Blind Spot Monitor System
        3. *3: w/ Stop and Start System
        4. *4: for Gasoline Model
        5. *5: for Sport Package

        HINT: 

        The illumination of each warning light and indicator light varies.

scientia non olet · About LEMON Manuals