LEMON Manuals: Even more car manuals for everyone
Home >> Lexus >> 2019 >> RX 450h Base >> Repair and Diagnosis >> Restraints >> Seat Belts >> Seat Belt (Service Information) >> Front Seat Outer Belt Assembly With Pre-TENSIONER >> Removal [08/2016 - 03/2018] >> Procedure

Removal [08/2016 - 03/2018]: Procedure

  1. PRECAUTION 
    NOTE:

    After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

    Refer to PRECAUTION [08/2016 - 12/2017] , or refer to PRECAUTION [12/2017 - 03/2018]

  2. REMOVE DECK BOARD ASSEMBLY 

    Refer to PROCEDURE - Step 2 [08/2016 - 12/2017] , or refer to PROCEDURE - Step 2 [12/2017 - 08/2019]

  3. REMOVE REAR DECK FLOOR BOX 

    Refer to PROCEDURE - Step 4 [08/2016 - 12/2017] , or refer to PROCEDURE - Step 4 [12/2017 - 08/2019]

  4. DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL 
    WARNING:
    • Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
    • If an SRS part is accidentally deployed, it may cause a serious injury.
    GTY581108Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    NOTE:

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Refer to INITIALIZATION [08/2016 - 12/2017] , or refer to INITIALIZATION [12/2017 - 03/2018]

  5. REMOVE FRONT DOOR SCUFF PLATE 

    Refer to PROCEDURE - Step 9 [08/2016 - 12/2017] , or refer to PROCEDURE - Step 9 [12/2017 - 08/2019]

  6. REMOVE REAR DOOR SCUFF PLATE 

    Refer to PROCEDURE - Step 11 [08/2016 - 12/2017] , or refer to PROCEDURE - Step 11 [12/2017 - 08/2019]

  7. REMOVE LOWER CENTER PILLAR GARNISH 

    Refer to PROCEDURE - Step 12 [08/2016 - 12/2017] , or refer to PROCEDURE - Step 12 [12/2017 - 08/2019]

  8. DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY 
    1. Remove the bolt and disconnect the floor anchor of the front seat outer belt assembly.
      GTY637898Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  9. REMOVE CENTER PILLAR GARNISH ASSEMBLY 

    Refer to PROCEDURE - Step 14 [08/2016 - 12/2017] , or refer to PROCEDURE - Step 14 [12/2017 - 08/2019]

  10. REMOVE FRONT SEAT OUTER BELT ASSEMBLY 
    1. Remove the nut and disconnect the shoulder anchor of the front seat outer belt assembly.
      GTY621803Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Using a screwdriver, pull out the locking button as shown in the illustration to release the lock and disconnect the pretensioner connector.
      GTY624576Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Protective Tape
      *b Locking Button
      *c Release

      HINT: 

      Tape the screwdriver tip before use.

    3. Disconnect the connector.
    4. Remove the 2 bolts.
      GTY674544Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    5. Disengage the 2 guides to remove the front seat outer belt assembly.
  11. REMOVE FRONT SHOULDER BELT ANCHOR ADJUSTER ASSEMBLY 
    1. Remove the 2 bolts.
      GTY621804Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Disengage the guide to remove the front shoulder belt anchor adjuster assembly.
scientia non olet · About LEMON Manuals