Data List / Active Test [08/2019 - ]
- DATA LIST NOTE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
HINT:
Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
- Connect the Techstream to the DLC3.
- Turn the engine switch on (IG).
- Turn the Techstream on.
- Enter the following menus:
- for Combination Meter: Body Electrical / Combination Meter / Data List.
- for Brake/EPB: Chassis / Brake/EPB / Data List.
- for Engine: Powertrain / Engine / Data List.
- Read the Data List according to the display on the Techstream.
- Combination Meter
Body Electrical > Combination Meter > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note ODO/TRIP Change SW ODO/TRIP switch OFF or ON OFF: Switch released
ON: Switch pushed- Vehicle Speed Meter Vehicle speed Min.: 0 km/h (0 mph), Max.: 255 km/h (158 mph) Almost the same as actual vehicle speed - Engine Rpm Engine speed Min.: 0 rpm, Max.: 12750 rpm Almost the same as actual tachometer - Coolant Temperature Engine coolant temperature Min.: 0°C (32°F), Max.: 127.5°C (261.5°F) 75 to 100°C (167 to 212°F): After warming up engine - Washer Switch Washer fluid level warning switch OFF or ON OFF: Washer fluid level not low
ON: Washer fluid level low- Oil Level SW Engine oil level sensor OFF or ON OFF: Engine oil level not low
ON: Engine oil level low- Light Control Up Switch Light control rheostat up switch OFF or ON OFF: Switch released
ON: Switch pushed- Light Control Down Switch Light control rheostat down switch OFF or ON OFF: Switch released
ON: Switch pushed- +B Voltage Value Battery voltage Min.: 0 V, Max.: 25.5 V 11 to 14 V - Fuel Input Fuel input Min.: 0 L, Max.: 127.5 L Fuel receiver gauge indicates F: 64.8 L
Fuel receiver gauge indicates 3/4: 54.0 L
Fuel receiver gauge indicates 1/2: 36.0 L
Fuel receiver gauge indicates 1/4: 18.0 L
Fuel receiver gauge indicates E: 7.2 LUnit: Liter Ambient Temperature Outside temperature Min.: -40°C (-40°F), Max.: 87.5°C (189.5°F) Almost the same as actual outside temperature The temperature displayed on the multi-information display is -40 to 50°C (-40 to 122°F) Multi Switch (Up) Steering pad switch (Up) OFF or ON OFF: Switch released
ON: Switch pushed- Multi Switch (Down) Steering pad switch (Down) OFF or ON OFF: Switch released
ON: Switch pushed- Multi Switch (Menu) Steering pad switch (Menu) OFF or ON OFF: Switch released
ON: Switch pushed- Multi Switch (Enter) Steering pad switch (Enter) OFF or ON OFF: Switch released
ON: Switch pushed- Multi Switch (Right) Steering pad switch (Right) OFF or ON OFF: Switch released
ON: Switch pushed- Multi Switch (Left) Steering pad switch (Left) OFF or ON OFF: Switch released
ON: Switch pushed- 2nd-Row Seatbelt Buckle (R) Rear seat belt buckle switch RH OFF or ON OFF: Rear seat belt RH fastened
ON: Rear seat belt RH unfastened- 2nd-Row Seatbelt Buckle (L) Rear seat belt buckle switch LH OFF or ON OFF: Rear seat belt LH fastened
ON: Rear seat belt LH unfastened- 2nd-Row Seatbelt Buckle (C) Rear seat belt buckle switch center OFF or ON OFF: Rear seat belt center fastened
ON: Rear seat belt center unfastened*1 3rd-Row Seatbelt Buckle (R) Rear No. 2 seat belt buckle switch RH OFF or ON OFF: Rear No. 2 seat belt RH fastened
ON: Rear No. 2 seat belt RH unfastened*2 3rd-Row Seatbelt Buckle (L) Rear No. 2 seat belt buckle switch LH OFF or ON OFF: Rear No. 2 seat belt LH fastened
ON: Rear No. 2 seat belt LH unfastened*2 Oil Pressure Switch Engine oil pressure switch OFF or ON OFF: Engine started
ON: Engine not started- Turn Signal Switch (Right) RH turn signal switch OFF or ON OFF: RH turn signal switch off
ON: RH turn signal switch on- Turn Signal Switch (Left) LH turn signal switch OFF or ON OFF: LH turn signal switch off
ON: LH turn signal switch on- Hazard Flasher Switch Hazard warning signal switch OFF or ON OFF: Hazard warning signal switch off
ON: Hazard warning signal switch on- Passenger Occupant Detection Switch Occupant detection sensor OFF or ON OFF: Front passenger seat not occupied
ON: Front passenger seat occupiedNot applicable to this vehicle Turn Switch Signal (Full Turn) Turn signal switch signal OFF or ON OFF: LH and RH turn signal switch off
ON: LH or RH turn signal switch on- Multi Switch (Back) Steering pad switch (Back) OFF or ON OFF: Switch released
ON: Switch pushed- Brake Fluid Amount Brake fluid level OK or Low OK: Brake fluid level normal
NG: Brake fluid level abnormal- Brake Negative Pressure Brake vacuum pressure OK or NG OK: Brake vacuum pressure normal
NG: Brake vacuum pressure abnormal- Driver Side Seatbelt Warning Buzzer Setting of the driver seat belt warning buzzer OFF or ON OFF: Seat belt warning buzzer does not sound at vehicle speed of 20 km/h (12 mph) or more when driver seat belt unfastened
ON: Seat belt warning buzzer sounds at vehicle speed of 20 km/h (12 mph) or more when driver seat belt unfastenedDisplays customize setting of Driver Side Seat Belt Warning Buzzer P-Seatbelt Warning Buzzer Setting of the front passenger seat belt warning buzzer OFF or ON OFF: Seat belt warning buzzer does not sound at vehicle speed of 20 km/h (12 mph) or more when front passenger seat belt unfastened
ON: Seat belt warning buzzer sounds at vehicle speed of 20 km/h (12 mph) or more when front passenger seat belt unfastenedDisplays customize setting of Front Passenger Side Seat Belt Warning Buzzer Rear Seatbelt Warning Buzzer Setting of the rear seat belt warning buzzer OFF or ON OFF: Seat belt warning buzzer does not sound at vehicle speed of 20 km/h (12 mph) or more when rear seat belt unfastened
ON: Seat belt warning buzzer sounds at vehicle speed of 20 km/h (12 mph) or more when rear seat belt unfastenedDisplays customize setting of Rear Seat Belt Warning Buzzer ODO Display Time After IG OFF Setting Setting of the ODO display time after the engine switch is turned off 30s, 60s, 600s or OFF Displays customize setting of ODO Display Time After the Engine Switch is Turned Off - Lane Change Flashing Times Setting Setting of the lane change flashing times OFF, 3, 4, 5, 6 or 7 Displays customize setting of Lane Change Flashing Times Setting - Flasher Sound Volume Adjustment Setting of the flasher sound volume adjustment Small, Medium or Large Displays customize setting of Flasher Sound Volume Adjustment - TPMS System Existence of function With or Without With: w/ Tire Pressure Warning System
Without: w/o Tire Pressure Warning System- LDA System Existence of function With or Without With: w/ Lane Control System
Without: w/o Lane Control System- PCS System Existence of function With or Without With: w/ Pre-collision System
Without: w/o Pre-collision System- AHS System Existence of function With or Without With: w/ Adaptive High Beam System
Without: w/o Adaptive High Beam System- ICS System Existence of function With or Without With: w/ Intelligent Clearance Sonar System
Without: w/o Intelligent Clearance Sonar System- Radar Cruise System Existence of function With or Without With: w/ Dynamic Radar Cruise Control System
Without: w/o Dynamic Radar Cruise Control System- Intuitive P/A System Existence of function With or Without With: w/ Intuitive Parking Assist System
Without: w/o Intuitive Parking Assist System- Back Door System Existence of function With or Without With: w/ Power Back Door System
Without: w/o Power Back Door System- Road Sign Assist System Existence of function With or Without With: w/ Road Sign Assist System
Without: w/o Road Sign Assist System- Number of Trouble Code The number of the DTC currently stored Min.: 0, Max.: 255 Number of stored DTCs displayed - - *1: w/ Rear No. 2 Seat (for 60/40 Split Type Rear No. 1 Seat) or without Rear No. 2 Seat
*2: w/ Rear No. 2 Seat
- *1: w/ Rear No. 2 Seat (for 60/40 Split Type Rear No. 1 Seat) or without Rear No. 2 Seat
- Brake/EPB
Chassis > Brake/EPB > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note Vehicle Speed Maximum wheel speed sensor reading Min.: 0 km/h (0 mph), Max.: 6553.5 km/h (4072 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations - Engine
Powertrain > Engine > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note Engine Speed Engine speed Min.: 0 rpm, Max.: 16383 rpm 650 to 750 rpm: Idling (shift lever in N, engine warmed up and A/C off) When the crankshaft position sensor is malfunctioning, "Engine Speed" is approximately 0 rpm or varies greatly from the actual engine speed. Coolant Temperature Engine coolant temperature Min.: -40°C (-40°F), Max.: 140°C (284°F) 75 to 100°C (167 to 212°F): After warming up This is the engine coolant temperature.
HINT:- After warming up the engine, the engine coolant temperature will be 75 to 100°C (167 to 212°F).
- After a long soak, the engine coolant temperature, intake air temperature and ambient air temperature will be approximately equal.
- If the value is -40°C (-40°F), or higher than 135°C (275°F), the sensor circuit is open or shorted.
- Check if the engine overheats if the value indicated is higher than 135°C (275°F).
- Combination Meter
- ACTIVE TEST
HINT:
Using the Techstream to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
- Connect the Techstream to the DLC3.
- Turn the engine switch on (IG).
- Turn the Techstream on.
- Enter the following menus: Body Electrical / Combination Meter / Active Test.
- Perform the Active Test according the display on the Techstream.
Body Electrical > Combination Meter > Active Test
Tester Display Measurement Item Control Range Diagnostic Note Speed Meter Operation Speedometer *1 - OFF, 0, 40, 80, 120 or 160 mph *5
- OFF, 0, 40, 80, 120, 160, 200 or 240 km/h *6
There is a deviation in the values displayed on the speedometer (Control range → Speedometer display)
for Optitron Meter Type (mph) *5:- 40 → 39.6 to 42.4
- 80 → 80.5 to 83.7
- 120 → 121.5 to 124.7
for Optitron Meter Type (km/h) *6:- 40 → 38.8 to 43.3
- 80 → 79.6 to 84.6
- 120 → 120.6 to 125.6
- 160 → 161.7 to 166.7
- 200 → 202.7 to 207.7
- 240 → 243.7 to 248.7
TachoMeter Operation Tachometer OFF, 0, 1000, 2000, 3000, 4000, 5000, 6000 or 7000 *1 Fuel Meter Operation Fuel receiver gauge OFF, Sender E, Empty, Warning, 1/4, 1/2, 3/4, Full or Sender F - A/T Indicator Operation 1 Shift indicator OFF, L, 2, 3, 4, D, N, R or P - A/T Indicator Operation 2 Shift indicator OFF, 8, 5, 6, 7, S or M - A/T Indicator Operation 3 Shift indicator OFF or D - Indicat. Lamp Airbag SRS warning light OFF or ON - Driver Side Seat Belt Driver or front passenger seat belt warning light OFF or ON - Indicat. Lamp ABS ABS warning light OFF or ON - Indicat. Lamp Charge Charge warning light OFF or ON *2 Indicat. Lamp Slip Slip indicator light OFF or ON - Indicat. Lamp Beam High beam indicator light OFF or ON - Indicat. Lamp Head Head indicator light OFF or ON *3 Indicat. Lamp Tail Tail indicator light OFF or ON *4 Indicat. Lamp Fr FOG Front fog indicator light OFF or ON - Indicat. Pre-Collision PCS warning light OFF or ON - Indicat. Lamp Fuel Fuel level warning light OFF or ON - Indicat. Tire Pressure Warning System Tire pressure warning light OFF or ON - Indicat. Lamp ECB Brake warning light / yellow (minor malfunction) OFF or ON - Indicat. ECONO Eco driving indicator light OFF or ON - Indicat. Lamp Brake Brake warning light / red (malfunction) OFF or ON - Indicat. EPS EPS warning light (red) OFF or ON - Master Warning Master warning light OFF or ON - Indicat. Brake Hold Brake hold indicator light OFF or ON - Indicat. Hold Brake hold warning light OFF or ON - Indicat. Park Parking brake warning light OFF or ON - Indicat. VSC OFF VSC OFF indicator light OFF or ON - Rear Seat Belt Rear seat belt warning light OFF or ON - Indicat. 4WD Lock AWD lock indicator light OFF or ON *9 Automatic High Beam Indicator Automatic high beam indicator light OFF or ON - PPS Indicator EPS warning light (yellow) OFF or ON - Turn Signal (Left) Indicator LH turn indicator light OFF or ON - Turn Signal (Right) Indicator RH turn indicator light OFF or ON - Check Engine Indicator MIL (Check engine warning light) OFF or ON - BSM Control Indicator BSM indicator light OFF or ON *7 ICS OFF Indicator ICS OFF indicator light OFF or ON *8 INTUITIVE P/A LCD OFF Indicator Clearance sonar OFF indicator light OFF or ON *8 RCTA OFF Indicator RCTA OFF indicator light OFF or ON - Water Temperature Meter Operation Engine coolant temperature receiver gauge OFF, LOW, NORMAL or HIGH - Meter Display 1 Multi-information display OFF or All - - *1: for Optitron Meter Type
- *2: for TFT Meter Type
- *3: w/ Head Indicator Light
- *4: w/ Tail Indicator Light
- *5: for Speedometer with Imperial Units Main Scale
- *6: for Speedometer with Metric Units Main Scale
- *7: w/ Blind Spot Monitor System
- *8: w/ Intelligent Clearance Sonar System
- *9: for AWD
HINT:
Active Test cannot be performed on the speedometer and tachometer for TFT meter type.