Brake Warning Light does not Come ON [03/2017 - ]: Procedure

1. Check if CAN communication system DTCs are output.

   Refer to DIAGNOSIS SYSTEM [03/2017 - 06/2019] , or refer to DIAGNOSIS SYSTEM [06/2019 - 04/2020] , or refer to DIAGNOSIS SYSTEM [04/2020 - 11/2021] , or refer to DIAGNOSIS SYSTEM [11/2021 - 10/2022] , or refer to DIAGNOSIS SYSTEM [10/2022 - 05/2023] , or refer to DIAGNOSIS SYSTEM [05/2023 - ]

   Result

   Result	Proceed to
   DTCs are not output.	A
   DTCs are output.	B

Result: 

B 

INSPECT CAN COMMUNICATION SYSTEM. Refer to  HOW TO PROCEED WITH TROUBLESHOOTING [03/2017 - 09/2018]  , or refer to  HOW TO PROCEED WITH TROUBLESHOOTING [09/2018 - 05/2023]  , or refer to  HOW TO PROCEED WITH TROUBLESHOOTING [05/2023 - ] 

Result: 

A 

See step  2

1. Connect the Techstream to the DLC3.
2. Turn the engine switch on (IG).
3. Select the Active Test on the Techstream.

   Refer to DATA LIST / ACTIVE TEST [03/2017 - 05/2023] , or refer to DATA LIST / ACTIVE TEST [05/2023 - ]

   Chassis > ABS/VSC/TRAC > Active Test 

   Tester Display	Measurement Item	Control Range	Diagnostic Note
   Brake Warning Light	Brake warning light / red (malfunction)	Warning light ON/OFF	Observe combination meter assembly

   Chassis > ABS/VSC/TRAC > Active Test 

   Tester Display
   Brake Warning Light

4. Select the Data List on the Techstream.

   Refer to DATA LIST / ACTIVE TEST [03/2017 - 05/2023] , or refer to DATA LIST / ACTIVE TEST [05/2023 - ]

   Chassis > ABS/VSC/TRAC > Data List 

   Tester Display	Measurement Item	Range	Normal Condition	Diagnostic Note
   Brake Warning Light	Brake warning light / red (malfunction)	ON or OFF	ON: Warning light on OFF: Warning light off	-

   Chassis > ABS/VSC/TRAC > Data List 

   Tester Display
   Brake Warning Light

5. Check the operating condition of the brake warning light / red (malfunction) when operating it using the Techstream.

   Result

   Result	Proceed to
   Brake warning light / red (malfunction) in the Data List does not change using the Active Test.	A
   Brake warning light / red (malfunction) in the Data List turns ON/OFF using the Active Test.	B

Result: 

A 

REPLACE SKID CONTROL ECU ASSEMBLY. Refer to  REMOVAL [03/2017 - 05/2023]  , or refer to  REMOVAL [05/2023 - ] 

Result: 

B 

See step  3

1. Turn the engine switch off.
2. Perform the Active Test of the combination meter assembly (meter CPU) using the Techstream.

   Refer to DATA LIST / ACTIVE TEST [03/2017 - ]

   Body Electrical > Combination Meter > Active Test 

   Tester Display
   Indicat. Lamp Brake

3. Check the combination meter assembly.

   OK

   The brake warning light / red (malfunction) turns on or off in accordance with Techstream operation.

   Result

   Proceed to
   OK
   NG

Result: 

OK 

REPLACE SKID CONTROL ECU ASSEMBLY. Refer to  REMOVAL [03/2017 - 05/2023]  , or refer to  REMOVAL [05/2023 - ] 

Result: 

NG 

INSPECT METER / GAUGE SYSTEM. Refer to  HOW TO PROCEED WITH TROUBLESHOOTING [03/2017 - ]