LEMON Manuals: Even more car manuals for everyone
Home >> Lexus >> 2019 >> IS 350 Base, RWD >> Repair and Diagnosis >> External Pages >> Different car >> Section 21 (Engine Control System (2GR-FSE) - Service Information) >> Camshaft Oil Control Valve >> Installation [04/2013 - 10/2017] >> Procedure

Installation [04/2013 - 10/2017]: Procedure

WARNING: This page does not describe the selected car, but rather 6 other vehicles, including the 2017 Lexus IS 350, 2017 Lexus IS 300, 2016 Lexus IS 350, 2016 Lexus IS 300, and 2015 Lexus IS 350. However, it is still accessible from the selected car via links, so may be relevant.
  1. INSTALL CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (for Intake Side of Bank 2) 
    1. Apply a light coat of engine oil to a new O-ring and install it to the camshaft timing oil control valve assembly.
    2. Install the camshaft timing oil control valve assembly to the cylinder head cover sub-assembly LH with the bolt.

      Torque: 10 N*m (102 kgf*cm, 7 ft.*lbf) 

      NOTE:
      • Do not allow foreign matter to contact the oil seal face of the camshaft timing oil control valve assembly (connecting surface with the cylinder head cover sub-assembly LH).
      • Make sure that the O-ring is not cracked or moved out of place when installing the camshaft timing oil control valve assembly.
    3. Connect the camshaft timing oil control valve assembly connector.
  2. INSTALL CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (for Exhaust Side of Bank 2) 
    1. Apply a light coat of engine oil to a new O-ring and install it to the camshaft timing oil control valve assembly.
    2. Install the camshaft timing oil control valve assembly to the cylinder head cover sub-assembly LH with the bolt.

      Torque: 10 N*m (102 kgf*cm, 7 ft.*lbf) 

      NOTE:
      • Do not allow foreign matter to contact the oil seal face of the camshaft timing oil control valve assembly (connecting surface with the cylinder head cover sub-assembly LH).
      • Make sure that the O-ring is not cracked or moved out of place when installing the camshaft timing oil control valve assembly.
    3. Connect the camshaft timing oil control valve assembly connector.
    4. Install the bracket to the cylinder head cover sub-assembly LH with the bolt.

      Torque: 21 N*m (214 kgf*cm, 15 ft.*lbf) 

    5. Connect the wire harness clamp to the bracket.
  3. INSTALL CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (for Intake Side of Bank 1) 
    1. Apply a light coat of engine oil to a new O-ring and install it to the camshaft timing oil control valve assembly.
    2. Install the camshaft timing oil control valve assembly to the cylinder head cover sub-assembly with the bolt.

      Torque: 10 N*m (102 kgf*cm, 7 ft.*lbf) 

      NOTE:
      • Do not allow foreign matter to contact the oil seal face of the camshaft timing oil control valve assembly (connecting surface with the cylinder head cover sub-assembly).
      • Make sure that the O-ring is not cracked or moved out of place when installing the camshaft timing oil control valve assembly.
    3. Connect the camshaft timing oil control valve assembly connector.
    4. Install the V-bank cover bracket sub-assembly to the cylinder head cover sub-assembly with the bolt.

      Torque: 10 N*m (102 kgf*cm, 7 ft.*lbf) 

  4. INSTALL CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (for Exhaust Side of Bank 1) 
    1. Apply a light coat of engine oil to a new O-ring and install it to the camshaft timing oil control valve assembly.
    2. Install the camshaft timing oil control valve assembly to the cylinder head cover sub-assembly with the bolt.

      Torque: 10 N*m (102 kgf*cm, 7 ft.*lbf) 

      NOTE:
      • Do not allow foreign matter to contact the oil seal face of the camshaft timing oil control valve assembly (connecting surface with the cylinder head cover sub-assembly).
      • Make sure that the O-ring is not cracked or moved out of place when installing the camshaft timing oil control valve assembly.
    3. Connect the camshaft timing oil control valve assembly connector.
  5. INSTALL INTAKE AIR SURGE TANK ASSEMBLY 

    Refer to INSTALLATION [04/2013 - 10/2017]

scientia non olet · About LEMON Manuals