LEMON Manuals: Even more car manuals for everyone
Home >> Lexus >> 2019 >> IS 350 Base, RWD >> Repair and Diagnosis >> External Pages >> Different car >> Section 140 (Charging System (2GR-FSE) - Service Information) >> Generator >> Installation [04/2013 - 10/2017] >> Procedure

Installation [04/2013 - 10/2017]: Procedure

WARNING: This page does not describe the selected car, but rather 6 other vehicles, including the 2017 Lexus IS 350, 2017 Lexus IS 300, 2016 Lexus IS 350, 2016 Lexus IS 300, and 2015 Lexus IS 350. However, it is still accessible from the selected car via links, so may be relevant.
  1. INSTALL GENERATOR ASSEMBLY 
    1. Using an E6 "TORX" socket wrench, install the stud bolt.

      Torque: 4.0 N*m (41 kgf*cm, 35 in.*lbf) 

    2. Install the wire harness bracket with the bolt (A).
      GTY460221Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Bolt A
      Bolt B

      Torque: 10 N*m (102 kgf*cm, 7 ft.*lbf) 

    3. Install the generator bracket with the bolt (B).

      Torque: 20 N*m (204 kgf*cm, 15 ft.*lbf) 

    4. Install the generator assembly with the 2 bolts.

      Torque: 43 N*m (438 kgf*cm, 32 ft.*lbf) 

    5. Install the generator bracket with the nut.

      Torque: 20 N*m (204 kgf*cm, 15 ft.*lbf) 

    6. Connect the engine wire with the nut.

      Torque: 9.8 N*m (100 kgf*cm, 87 in.*lbf) 

    7. Install the terminal cap.
    8. Install the engine wire bracket with the bolt.

      Torque: 10 N*m (102 kgf*cm, 7 ft.*lbf) 

    9. Attach the 2 clamps, and connect the generator assembly connector.
  2. CONNECT WIRE HARNESS 
    1. Connect the wire harness with the 3 nuts.

      Torque: 10 N*m (102 kgf*cm, 7 ft.*lbf) 

    2. Connect the VVT sensor connector and camshaft timing oil control valve assembly connector.
  3. INSTALL NO. 2 IDLER PULLEY SUB-ASSEMBLY 

    Refer to PROCEDURE - Step 2

  4. INSTALL COOLING FAN ECU 
    1. Install the cooling fan ECU with the 2 screws.

      Torque: 2.6 N*m (27 kgf*cm, 23 in.*lbf) 

    2. Connect the 3 cooling fan ECU connectors.
  5. INSTALL NO. 2 ENGINE COVER 

    Refer to PROCEDURE - Step 29

  6. INSTALL NO. 1 RADIATOR HOSE 
    1. Install the No. 1 radiator hose and slide the 2 clips to secure it.
  7. INSTALL V-RIBBED BELT 

    Refer to INSTALLATION [04/2013 - 10/2017]

  8. ADD ENGINE COOLANT 

    Refer to PROCEDURE - Step 5 [04/2013 - 08/2015] , or refer to PROCEDURE - Step 5 [08/2015 - 10/2017]

  9. INSPECT ENGINE COOLANT 

    Refer to PROCEDURE - Step 6 [04/2013 - 08/2015] , or refer to PROCEDURE - Step 6 [08/2015 - 10/2017]

  10. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL 
    NOTE:

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Refer to INITIALIZATION [04/2013 - 06/2014] , or refer to INITIALIZATION [06/2014 - 08/2015] , or refer to INITIALIZATION [08/2015 - 10/2016] , or refer to INITIALIZATION [10/2016 - 10/2017]

scientia non olet · About LEMON Manuals