LEMON Manuals: Even more car manuals for everyone
Home >> Lexus >> 2019 >> ES 350 Luxury >> Repair and Diagnosis >> External Pages >> Different car >> Section 73 (Airbag System (Hybrid) - Diagnostic Codes (1 Of 3)) >> AIRBAG SYSTEM (for HV Model) >> DTC B1630: Curtain Shield Airbag Sensor (RH); DTC B1632: Curtain Shield Airbag Sensor Lost Communication (RH) [06/2018 - 09/2022] >> Procedure

DTC B1630: Curtain Shield Airbag Sensor (RH); DTC B1632: Curtain Shield Airbag Sensor Lost Communication (RH) [06/2018 - 09/2022]: Procedure

WARNING: This page does not describe the selected car, but rather 6 other vehicles, including the 2024 Lexus ES 300h, 2023 Lexus ES 300h, 2022 Lexus ES 300h, 2021 Lexus ES 300h, and 2020 Lexus ES 300h. However, it is still accessible from the selected car via links, so may be relevant.
  1. CHECK SIDE NO. 2 AIRBAG SENSOR ASSEMBLY RH 
    1. Turn the power switch off.
      GTY436338Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *1 Side No. 2 Airbag Sensor Assembly LH
      *2 Airbag ECU Assembly
    2. Disconnect the cable from the negative (-) auxiliary battery terminal.
      WARNING:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

    3. Interchange the side No. 2 airbag sensor assembly RH with LH and connect the connectors.
    4. Connect the cable to the negative (-) auxiliary battery terminal.
    5. Turn the power switch on (IG), and wait for at least 60 seconds.
    6. Clear the DTCs stored in memory.

      Body Electrical > SRS Airbag > Clear DTCs 

    7. Turn the power switch off.
    8. Turn the power switch on (IG), and wait for at least 60 seconds.
    9. Check for DTCs.

      Body Electrical > SRS Airbag > Trouble Codes 

      HINT: 

      Codes other than DTCs B1630, B1632, B1635 and B1637 may be output at this time, but they are not related to this check.

      Result

      Result Proceed to
      DTC B1630 or B1632 is output. A
      DTC B1635 or B1637 is output. B
      DTCs B1630, B1632, B1635 and B1637 are not output. C
    10. Turn the power switch off.
    11. Disconnect the cable from the negative (-) auxiliary battery terminal.
      WARNING:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

    12. Return the side No. 2 airbag sensor assembly RH and LH to their original positions and connect the connectors.

    Result: 

    A 

    REPLACE AIRBAG ECU ASSEMBLY. Refer to  REMOVAL [06/2018 - 08/2020]  , or refer to  REMOVAL [08/2020 - 08/2021]  , or refer to  REMOVAL [08/2021 - 09/2022] 

    Result: 

    B 

    REPLACE SIDE NO. 2 AIRBAG SENSOR ASSEMBLY RH. Refer to  REMOVAL [06/2018 - 08/2020]  , or refer to  REMOVAL [08/2020 - 08/2021]  , or refer to  REMOVAL [08/2021 - 09/2022] 

    Result: 

    C 

    USE SIMULATION METHOD TO CHECK. Refer to  HOW TO PROCEED WITH TROUBLESHOOTING [06/2018 - ] 

scientia non olet · About LEMON Manuals