Installation [06/2018 - 01/2020]: Procedure

WARNING: This page does not describe the selected car, but rather 6 other vehicles, including the 2024 Lexus ES 300h, 2023 Lexus ES 300h, 2022 Lexus ES 300h, 2021 Lexus ES 300h, and 2020 Lexus ES 300h. However, it is still accessible from the selected car via links, so may be relevant.

INSTALL TRANSMISSION FLOOR SHIFT ASSEMBLY
1. Engage the clamp to connect the wire harness to the transmission floor shift assembly.
2. Connect the shift lock control ECU connector.
3. Engage the clamp to connect the wire harness to the transmission floor shift assembly.
4. Connect the transmission control switch connector.
5. Install the clip to the No. 1 console box duct.
6. Temporarily install the transmission floor shift assembly to the vehicle body with the 4 bolts.
  
  Fig 1: Transmission Floor Shift Assembly Bolt Tightening Sequence [06/2018 - 01/2020]
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
7. Tighten the 4 bolts in the order shown in the illustration.
  Torque: 12 N.m (122 kgf/cm, 9 ft.lbf)

CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY

NOTE:

Before connecting the transmission control cable assembly, check that the shift lever is in N.

Slide the slider of the transmission control cable assembly in the direction indicated by the arrow in the illustration and pull the lock piece outward.

GTY440136

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

*a	Slider
*b	Lock Piece
*c	Slide
*d	Pull

Turn the lock nut of the transmission control cable assembly counterclockwise. While holding the lock nut, push in the stopper.

GTY837803

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

*a	Lock Nut
*b	Push in
*c	Stopper

Connect the transmission control cable assembly to the transmission floor shift assembly.

GTY816188

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

*a

Stopper

NOTE:

After installation, check that the outer part of the stopper is as shown in the illustration.

Connect the transmission control cable assembly to the transmission floor shift assembly.

GTY784274

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

*a	Lock Piece
*b	Adjuster Case

NOTE:

Check that the lock piece is pulled out.
Push the end of the transmission control cable assembly all the way to the base of the transmission floor shift assembly pin.
Connect the transmission control cable assembly so that the lock piece faces the driver side.

Push the lock piece into the adjuster case.

GTY615783

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

*a	Lock Piece
*b	Push in
*c	Adjuster Case

NOTE:

Check that the shift lever is in N.
Securely push in the lock piece until the slider lock is engaged.

When pushing in the lock piece of the adjuster case to lock it, remove your hand from the lever shaft.

GTY928110

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

*1	Transmission Control Cable Assembly
*a	Lever Shaft

When pushing in the lock piece of the adjuster case to lock it, do not move the lever shaft or transmission control cable assembly forward or backward.

After adjusting the shift lever position, check the position and operation of the shift lever. If there is a problem, adjust the shift lever position again.

INSTALL CONSOLE BOX ASSEMBLY
Refer to INSTALLATION [06/2018 - 08/2020]
INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY
See step 1

INSTALL SHIFT LOCK RELEASE BUTTON COVER

Engage the 2 claws to install the shift lock release button cover to the upper console panel sub-assembly.

GTY809619

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

INSPECT SHIFT LEVER POSITION
See step 2
ADJUST SHIFT LEVER POSITION
Refer to ADJUSTMENT [06/2018 - 01/2020]