LEMON Manuals: Even more car manuals for everyone
Home >> Lexus >> 2019 >> ES 350 Luxury >> Repair and Diagnosis >> External Pages >> Different car >> Section 71 (Hybrid Transaxle System (P710) - Service Information) >> Shift Lever Position Sensor >> Installation [06/2018 - ] >> Procedure

Installation [06/2018 - ]: Procedure

WARNING: This page does not describe the selected car, but rather 6 other vehicles, including the 2024 Lexus ES 300h, 2023 Lexus ES 300h, 2022 Lexus ES 300h, 2021 Lexus ES 300h, and 2020 Lexus ES 300h. However, it is still accessible from the selected car via links, so may be relevant.
  1. INSTALL SHIFT LEVER POSITION SENSOR 
    1. Move the shift lever to N.
    2. Temporarily install the shift lever position sensor to the hybrid vehicle transaxle assembly with the 2 bolts.
      NOTE:
      • Do not reuse the shift lever position sensor if it has been dropped or subjected to a severe impact.
      • Do not allow moisture to adhere to the connector terminal.
    3. Install the lock plate to the shift lever position sensor with the lock nut.

      Torque: 6.9 N.m (70 kgf/cm, 61 in.lbf) 

    4. Temporarily install the control shaft lever to the shift lever position sensor.
    5. Turn the control shaft lever clockwise until it stops, then turn it counterclockwise 2 notches.
      GTY741264Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    6. Remove the control shaft lever from the shift lever position sensor.
    7. Align the indicator with the neutral basic line.
      GTY741927Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Neutral Basic Line
      *b Indicator
      *c Range of Play
      NOTE:

      The indicator of the lock plate has a certain amount of play. Align the center point of the range of play with the neutral basic line.

    8. Tighten the 2 bolts.

      Torque: 11 N.m (112 kgf/cm, 8 ft.lbf) 

    9. Using a screwdriver with its tip wrapped with protective tape, secure the lock nut with the lock plate.
    10. Install the control shaft lever and washer to the shift lever position sensor with the nut.

      Torque: 12.7 N.m (130 kgf/cm, 9 ft.lbf) 

    11. Connect the shift lever position sensor connector.
  2. CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY 
    1. Engage the 2 claws to install a new clip to the transmission control cable assembly.
    2. Using a screwdriver, engage the 4 claws and install the transmission control cable assembly to the No. 1 transmission control cable bracket.
      GTY746243Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *1 Transmission Control Cable Assembly
      *2 No. 1 Transmission Control Cable Bracket
      *a Claw (A)
      *b Claw (B)
      NOTE:
      • Make sure that the claws (A) of the clip are securely engaged in the grooves of the bracket.
      • Make sure that the transmission control cable assembly is securely installed inside of the claws (B) of the clip.
    3. Connect the transmission control cable assembly to the control shaft lever with the nut.

      Torque: 12 N.m (122 kgf/cm, 9 ft.lbf) 

  3. INSTALL AIR CLEANER ASSEMBLY WITH AIR CLEANER HOSE 

    Refer to PROCEDURE - Step 17

  4. INSTALL NO. 1 ENGINE COVER SUB-ASSEMBLY 

    Refer to PROCEDURE - Step 46 [06/2018 - 08/2021] , or refer to PROCEDURE - Step 47 [08/2021 - ]

  5. INSTALL INLET AIR CLEANER ASSEMBLY 

    Refer to PROCEDURE - Step 18

  6. INSTALL COOL AIR INTAKE DUCT SEAL 

    Refer to PROCEDURE - Step 2 [06/2018 - 08/2021] , or refer to PROCEDURE - Step 2 [08/2021 - 09/2022] , or refer to PROCEDURE - Step 2 [09/2022 - ]

  7. INSPECT SHIFT LEVER POSITION SENSOR POSITION 

    See step  2

  8. ADJUST SHIFT LEVER POSITION SENSOR POSITION 

    See step  3

  9. INSPECT SHIFT LEVER POSITION 

    See step  2 [06/2018 - 09/2022], or see step  2 [09/2022 - ]

  10. ADJUST SHIFT LEVER POSITION 

    See step  3 [06/2018 - 09/2022], or see step  3 [09/2022 - ]

  11. INSTALL NO. 2 ENGINE UNDER COVER ASSEMBLY 

    Refer to PROCEDURE - Step 42 [06/2018 - 08/2021] , or refer to PROCEDURE - Step 43 [08/2021 - ]

  12. INSTALL NO. 1 ENGINE UNDER COVER 

    Refer to PROCEDURE - Step 43 [06/2018 - 08/2021] , or refer to PROCEDURE - Step 44 [08/2021 - ]

  13. INSTALL FRONT WHEEL OPENING EXTENSION PAD LH 

    Refer to PROCEDURE - Step 44 [06/2018 - 08/2021] , or refer to PROCEDURE - Step 45 [08/2021 - ]

  14. INSTALL FRONT WHEEL OPENING EXTENSION PAD RH 

    Refer to PROCEDURE - Step 45 [06/2018 - 08/2021] , or refer to PROCEDURE - Step 46 [08/2021 - ]

scientia non olet · About LEMON Manuals