LEMON Manuals: Even more car manuals for everyone
Home >> Lexus >> 2019 >> ES 350 Luxury >> Repair and Diagnosis >> External Pages >> Different car >> Section 64 (Fuel System (A25A-FXS) - Service Information) >> FUEL INJECTOR (for Port Injection) >> Removal [09/2022 - ] >> Procedure

Removal [09/2022 - ]: Procedure

WARNING: This page does not describe the selected car, but rather 6 other vehicles, including the 2024 Lexus ES 300h, 2023 Lexus ES 300h, 2022 Lexus ES 300h, 2021 Lexus ES 300h, and 2020 Lexus ES 300h. However, it is still accessible from the selected car via links, so may be relevant.
  1. PRECAUTION 
    NOTE:

    After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

  2. DISCHARGE FUEL SYSTEM PRESSURE 

    Refer to PRECAUTION [08/2020 - ]

  3. DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL 

    Refer to PROCEDURE - Step 1

  4. REMOVE THROTTLE BODY WITH MOTOR ASSEMBLY 

    Refer to REMOVAL [06/2018 - ]

  5. REMOVE EGR VALVE ASSEMBLY 

    Refer to REMOVAL [09/2022 - ]

  6. REMOVE NO. 2 WATER BY-PASS PIPE 

    Refer to PROCEDURE - Step 8

  7. DISCONNECT FUEL TUBE SUB-ASSEMBLY 
    1. Remove the fuel pipe clamp from the fuel tube connector.
      GTY760014Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Disconnect the fuel tube sub-assembly from the fuel pump assembly and fuel delivery pipe sub-assembly.
      GTY836018Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      Refer to PRECAUTION [08/2020 - ]

  8. REMOVE NO. 1 FUEL PIPE SUB-ASSEMBLY 
    WARNING:

    To prevent serious injury due to fuel spray from the high-pressure fuel lines, always discharge fuel system pressure before removing any fuel system components.

    1. Disconnect the ignition coil connector.
      GTY814962Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. for EGR Valve Bracket Connection Type:
      1. Using a 17 mm union nut wrench, loosen the 2 union nuts of the No. 1 fuel pipe sub-assembly.
        GTY814961Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. for Cylinder Head Cover Sub-assembly Connection Type:
      1. Using a 17 mm union nut wrench, loosen the 2 union nuts of the No. 1 fuel pipe sub-assembly.
        GTY948110Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
        Union Nut
        Bolt
      2. Using an 8 mm socket wrench, remove the bolt.
    4. Loosen the 2 bolts of the fuel pump assembly.
      GTY763239Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    5. Remove the No. 1 fuel pipe sub-assembly from the fuel delivery pipe and fuel pump assembly.
  9. REMOVE FUEL (ENGINE ROOM SIDE) PUMP ASSEMBLY 

    See step  8

  10. REMOVE FUEL DELIVERY PIPE SUB-ASSEMBLY 
    1. Disconnect the No. 5 engine wire connector.
      GTY760009Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Remove the 2 bolts and fuel delivery pipe sub-assembly with the 4 port fuel injector assemblies from the cylinder head sub-assembly.
      GTY773619Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      NOTE:
      • If fuel intrudes into the combustion chamber, there may be adverse affects to the engine main body.
      • Be careful not to drop the port fuel injector assemblies when removing the fuel delivery pipe sub-assembly.
  11. REMOVE NO. 1 DELIVERY PIPE SPACER 
    1. Remove the 2 No. 1 delivery pipe spacers from the cylinder head sub-assembly.
      GTY760008Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  12. REMOVE INJECTOR VIBRATION INSULATOR 
    1. Remove the 4 injector vibration insulators from the cylinder head sub-assembly.
      GTY760011Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  13. REMOVE NO. 5 ENGINE WIRE 
    1. Disconnect the 4 port fuel injector assembly connectors and No. 2 fuel pressure sensor connector.
      GTY771589Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Disengage the 2 clamps to remove the No. 5 engine wire from the fuel delivery pipe sub-assembly.
  14. REMOVE PORT FUEL INJECTOR ASSEMBLY 
    1. Pull the 4 port fuel injector assemblies out of the fuel delivery pipe sub-assembly.
      GTY754430Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Remove the O-ring from each port fuel injector assembly.
      GTY754415Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. Attach a tag or label with the corresponding cylinder number to each port fuel injector assembly so that they can be installed to their original locations.
      NOTE:

      Cover the port fuel injector assemblies with plastic bags to prevent damage and contamination.

      GTY766507Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
scientia non olet · About LEMON Manuals