LEMON Manuals: Even more car manuals for everyone
Home >> Lexus >> 2019 >> ES 350 Luxury >> Repair and Diagnosis >> External Pages >> Different car >> Section 33 (Hybrid Battery Control System - Service Information (3 Of 3)) >> HV BATTERY STACK (for LITHIUM-ION BATTERY) >> Removal [09/2022 - ] >> Procedure

Removal [09/2022 - ]: Procedure

WARNING: This page does not describe the selected car, but rather 6 other vehicles, including the 2024 Lexus ES 300h, 2023 Lexus ES 300h, 2022 Lexus ES 300h, 2021 Lexus ES 300h, and 2020 Lexus ES 300h. However, it is still accessible from the selected car via links, so may be relevant.
  1. READ VALUE USING TECHSTREAM 
    1. Connect the Techstream to the DLC3.
    2. Turn the power switch on (IG).
    3. Enter the following menus: Powertrain / HV Battery / Data List / Hybrid Battery Temperature 1 to 6.

      Powertrain > HV Battery > Data List 

      Tester Display
      Hybrid Battery Temperature 1
      Hybrid Battery Temperature 2
      Hybrid Battery Temperature 3
      Hybrid Battery Temperature 4
      Hybrid Battery Temperature 5
      Hybrid Battery Temperature 6
    4. Read the Data List.
      NOTE:

      If any of the temperatures listed in "Hybrid Battery Temperature 1 to 6" are 50°C or more, leave the vehicle until the temperature drops to less than 50°C.

  2. REMOVE HV BATTERY 

    Refer to REMOVAL [09/2022 - ]

  3. REMOVE UPPER HV BATTERY COVER SUB-ASSEMBLY 

    Refer to PROCEDURE - Step 20

  4. REMOVE NO. 1 HV BATTERY HOSE 

    Refer to PROCEDURE - Step 21

  5. REMOVE HV BATTERY JUNCTION BLOCK ASSEMBLY 

    See step  18

  6. REMOVE HYBRID BATTERY TERMINAL BLOCK 

    See step  19

  7. REMOVE NO. 2 HYBRID BATTERY SHIELD SUB-ASSEMBLY 
    WARNING:

    Be sure to wear insulated gloves and protective goggles.

    1. Remove the bolt, 3 nuts and No. 2 hybrid battery shield sub-assembly from the HV battery.
      GTY764148Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  8. REMOVE NO. 1 HV BATTERY INTAKE DUCT LH 
    WARNING:

    Be sure to wear insulated gloves and protective goggles.

    1. Remove the clip to disconnect the No. 1 hybrid battery intake duct LH from the HV battery.
      GTY764137Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Disengage the claw of hybrid battery thermistor (sensor portion) and remove the No. 1 hybrid battery intake duct LH.
  9. REMOVE BATTERY ECU ASSEMBLY 

    Refer to PROCEDURE - Step 22

  10. REMOVE NO. 1 HV SUPPLY STACK SUB-ASSEMBLY 
    WARNING:

    Be sure to wear insulated gloves and protective goggles.

    1. Disconnect the connector.
      NOTE:

      Insulate each disconnected high-voltage connector with insulating tape. Wrap the connector from the wire harness side to the end of the connector.

      GTY773735Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Disconnect the connector.
      GTY764143Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. Disengage the claw.
      GTY764141Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    4. Remove the 4 nuts and No. 1 HV supply stack sub-assembly.
      GTY764142Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  11. REMOVE NO. 2 HV SUPPLY STACK SUB-ASSEMBLY 
    WARNING:

    Be sure to wear insulated gloves and protective goggles.

    1. Remove the nut and disconnect the earth terminal.
      GTY764139Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Disengage the clamp.
      GTY764140Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. Disengage the claw.
      GTY764138Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    4. Remove the 4 nuts and No. 2 HV supply stack sub-assembly.
      GTY773734Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  12. PERFORM RECOVERY INSPECTION 
    1. Before returning the HV supply stack sub-assembly, make sure to perform a recovery inspection.

      Refer to RECOVERY INSPECTION [08/2020 - ] 

scientia non olet · About LEMON Manuals