LEMON Manuals: Even more car manuals for everyone
Home >> Lexus >> 2019 >> ES 350 Luxury >> Repair and Diagnosis >> External Pages >> Different car >> Section 231 (Parking Support Alert System - Diagnostic Codes & Circuit Tests) >> Parking Support Alert System >> DTC C1AE8-87: Ultrasonic Sensor (Rear Right Center) Missing Message [09/2022 - ] >> Procedure

DTC C1AE8-87: Ultrasonic Sensor (Rear Right Center) Missing Message [09/2022 - ]: Procedure

WARNING: This page does not describe the selected car, but rather 6 other vehicles, including the 2024 Lexus ES 350, 2024 Lexus ES 300h, 2024 Lexus ES 250, 2023 Lexus ES 350, and 2023 Lexus ES 300h. However, it is still accessible from the selected car via links, so may be relevant.
  1. VEHICLE CONDITION AND WORK DETAILS CHECK 
    1. Check the vehicle condition and work details.

      Result

      Result Proceed to
      The clearance warning ECU assembly or ultrasonic sensor has not been replaced A
      The clearance warning ECU assembly or ultrasonic sensor has been replaced B

    Result: 

    B 

    GO TO CALIBRATION. Refer to  CALIBRATION [09/2022 - ] 

    Result: 

    A 

    See step  2

  2. CHECK CONNECTOR CONNECTION CONDITION (ULTRASONIC SENSOR) 
    1. Check that the connector is properly connected to the rear corner ultrasonic sensor and rear center ultrasonic sensor.

      Result

      Proceed to
      NEXT

    Result: 

    NEXT 

    See step  3

  3. CHECK FOR DTC 
    1. According to the display on the GTS, check for DTCs.

      Body Electrical > Clearance Warning > Trouble Codes 

    2. According to the display on the GTS, clear the DTCs.

      Body Electrical > Clearance Warning > Clear DTCs 

    3. Recheck for DTCs.

      Body Electrical > Clearance Warning > Trouble Codes 

      Result

      Result Proceed to
      C1AE8-87 is not output A
      C1AE8-87 is output B

    Result: 

    A 

    END (CONNECTOR CONNECTION MALFUNCTION) 

    Result: 

    B 

    See step  4

  4. CHECK CONNECTOR CONNECTION CONDITION (CLEARANCE WARNING ECU ASSEMBLY) 
    1. Check that the connector is properly connected to the clearance warning ECU assembly.

      Result

      Proceed to
      NEXT

    Result: 

    NEXT 

    See step  5

  5. CHECK FOR DTC 
    1. According to the display on the GTS, check for DTCs.

      Body Electrical > Clearance Warning > Trouble Codes 

    2. According to the display on the GTS, clear the DTCs.

      Body Electrical > Clearance Warning > Clear DTCs 

    3. Recheck for DTCs.

      Body Electrical > Clearance Warning > Trouble Codes 

      DTC OUTPUT COMBINATION:

      Symptoms DTC Detection
      C1AE9-87 C1AE8-87 C1AE7-87 C1AE6-87
      Symptom 1 Not output Not output Not output Not output
      Symptom 2 Output Output Output Output
      Symptom 3 Not output Output Output Output
      Symptom 4 Not output Not output Output Output
      Symptom 5 Not output Not output Not output Output
      Symptom 6 Not output Output Not output Not output

      Result

      Result Proceed to
      Listed under symptom 1 in combination table A
      Listed under symptom 2 in combination table B
      Listed under symptom 3 in combination table C
      Listed under symptom 4 in combination table D
      Listed under symptom 5 in combination table E
      Listed under symptom 6 in combination table F

    Result: 

    A 

    USE SIMULATION METHOD TO CHECK. Refer to  HOW TO PROCEED WITH TROUBLESHOOTING [06/2018 - ] 

    Result: 

    B 

    GO TO CORRESPONDING FLOWCHART (PARKING SUPPORT ALERT SYSTEM (C1AE9-87)). Refer to  DTC C1AE9-87: Ultrasonic Sensor (Rear Right Corner) Missing Message [09/2022 - ]  

    Result: 

    D 

    GO TO CORRESPONDING FLOWCHART (PARKING SUPPORT ALERT SYSTEM (C1AE7-87)). Refer to  DTC C1AE7-87: Ultrasonic Sensor (Rear Left Center) Missing Message [09/2022 - ]  

    Result: 

    E 

    GO TO CORRESPONDING FLOWCHART (PARKING SUPPORT ALERT SYSTEM (C1AE6-87)). Refer to  DTC C1AE6-87: Ultrasonic Sensor (Rear Left Corner) Missing Message [09/2022 - ]  

    Result: 

    F 

    See step  7

    Result: 

    C 

    See step  6

  6. CHECK WIRE HARNESS AND CONNECTOR (REAR CORNER ULTRASONIC SENSOR RH - REAR CENTER ULTRASONIC SENSOR RH) 
    1. Disconnect the S1 rear corner ultrasonic sensor RH connector.
    2. Disconnect the S2 rear center ultrasonic sensor RH connector.
    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      S1-1 (BO) - S2-4 (BI) Always Below 1 Ω
      S1-2 (SO) - S2-5 (SI) Always Below 1 Ω
      S1-3 (EO) - S2-6 (EI) Always Below 1 Ω
      S1-1 (BO) or S2-4 (BI) - Body ground Always 10 kΩ or higher
      S1-2 (SO) or S2-5 (SI) - Body ground Always 10 kΩ or higher
      S1-3 (EO) or S2-6 (EI) - Body ground Always 10 kΩ or higher

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPAIR OR REPLACE WIRE HARNESS OR CONNECTOR 

    Result: 

    OK 

    See step  7

  7. REPLACE REAR CENTER ULTRASONIC SENSOR RH 
    1. Replace the rear center ultrasonic sensor RH with a new or normally functioning one.

      Refer to REMOVAL [09/2022 - ]

      HINT: 

      To check if the ultrasonic sensor is functioning correctly, replace it with another ultrasonic sensor.

      Result

      Proceed to
      NEXT

    Result: 

    NEXT 

    See step  8

  8. CHECK FOR DTC 
    1. According to the display on the GTS, check for DTCs.

      Body Electrical > Clearance Warning > Trouble Codes 

    2. According to the display on the GTS, clear the DTCs.

      Body Electrical > Clearance Warning > Clear DTCs 

    3. Recheck for DTCs.

      Body Electrical > Clearance Warning > Trouble Codes 

      Result

      Result Proceed to
      No DTC is output A
      "C1AE8-87" is output B

    Result: 

    A 

    END (REAR CENTER ULTRASONIC SENSOR RH WAS DEFECTIVE) 

    Result: 

    B 

    REPLACE CLEARANCE WARNING ECU ASSEMBLY. Refer to  REMOVAL [09/2022 - ] 

scientia non olet · About LEMON Manuals