DTC P0340-31: Camshaft Position Sensor "A" Bank 1 or Single Sensor No Signal [06/2018 - 08/2020]: Procedure

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

HINT: 

Make sure that the connector is properly connected. If it is not, securely connect it and check for DTCs again.

1. Disconnect the camshaft position sensor (for intake camshaft) connector.
2. Turn the power switch on (IG).
3. Measure the voltage according to the value(s) in the table below.

   Standard Voltage

   Tester Connection	Condition	Specified Condition
   C51-3 (VC) - Body ground	Power switch on (IG)	4.5 to 5.5 V
   C51-1 (VVI+) - Body ground	Power switch on (IG)	3.0 to 5.0 V

4. Turn the power switch off and wait for at least 30 seconds.
5. Measure the resistance according to the value(s) in the table below.

   Standard Resistance

   Tester Connection	Condition	Specified Condition
   C51-3 (VC) - C51-1 (VVI+)	Power switch off	1.425 to 1.575 kΩ
   C51-2 (VVI-) - Body ground	Always	Below 1 Ω

   Result

   Proceed to
   OK
   NG

Result: 

NG 

See step  4

Result: 

OK 

See step  2

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Visually check the camshaft position sensor (for intake camshaft) for damage.
2. Check the camshaft position sensor (for intake camshaft) installation condition.

   OK

   The camshaft position sensor (for intake camshaft) does not have any damage and is installed properly.

   Result

   Proceed to
   OK
   NG

Result: 

NG 

SECURELY REINSTALL CAMSHAFT POSITION SENSOR (FOR INTAKE CAMSHAFT). Refer to  INSTALLATION [06/2018 - ] 

Result: 

OK 

See step  3

1. Check the timing rotor of the intake camshaft.

   OK

   Camshaft timing rotor does not have any cracks or deformation.

   HINT: 

   Perform "Inspection After Repair" after replacing the intake camshaft.

   Refer to INITIALIZATION [06/2018 - 07/2019] , or refer to INITIALIZATION [07/2019 - 08/2020]

   Result

   Proceed to
   OK
   NG

Result: 

OK 

REPLACE CAMSHAFT POSITION SENSOR (FOR INTAKE CAMSHAFT). Refer to  REMOVAL [06/2018 - ] 

Result: 

NG 

REPLACE INTAKE CAMSHAFT. Refer to  REMOVAL [06/2018 - 08/2021] 

1. Disconnect the camshaft position sensor (for intake camshaft) connector.
2. Disconnect the ECM connector.
3. Measure the resistance according to the value(s) in the table below.

   Standard Resistance

   Tester Connection	Condition	Specified Condition
   C51-1 (VVI+) - C88-90 (VV1+)	Always	Below 1 Ω
   C51-2 (VVI-) - C88-89 (VV1-)	Always	Below 1 Ω
   C51-3 (VC) - C88-88 (VCV1)	Always	Below 1 Ω
   C51-1 (VVI+) or C88-90 (VV1+) - Body ground and other terminals	Always	10 kΩ or higher
   C51-2 (VVI-) or C88-89 (VV1-) - Body ground and other terminals	Always	10 kΩ or higher
   C51-3 (VC) or C88-88 (VCV1) - Body ground and other terminals	Always	10 kΩ or higher

   Result

   Proceed to
   OK
   NG

Result: 

OK 

REPLACE ECM. Refer to  REMOVAL [06/2018 - 08/2020] 

Result: 

NG 

REPAIR OR REPLACE HARNESS OR CONNECTOR