Luggage Compartment Door Closer does not Operate [08/2021 - ]: Procedure

1. Read the customize setting according to the display on the Techstream.

   PSD & PBD operation 

   Tester Display	Description	Default	Setting	ECU
   PBD Power Closer Operation Setting	Status of the power trunk lid and luggage compartment door closer setting	Power Operation OFF/Closer Operation OFF	$00:Power Operation OFF/Closer Operation OFF,$01:Power Operation OFF/Closer Operation ON,$03:Power Operation ON/Closer Operation ON	Luggage closer motor assembly

   Result

   Result	Proceed to
   The customize setting is not set to Power Operation OFF/Closer Operation OFF	A
   The customize setting is set to Power Operation OFF/Closer Operation OFF	B

Result: 

B 

PERFORM CUSTOMIZE SETTING 

Result: 

A 

See step  2

1. Clear the DTCs.

   Body Electrical > Back Door > Clear DTCs 

   Result

   Proceed to
   NEXT

Result: 

NEXT 

See step  3

1. Wait for approximately 10 seconds.

   Result

   Proceed to
   NEXT

Result: 

NEXT 

See step  4

1. Check for DTCs.

   Body Electrical > Back Door > Trouble Codes 

   Result

   Result	Proceed to
   B2250-01 and B2251-01 are not output	A
   B2250-01 or B2251-01 is output	B

Result: 

B 

GO TO DIAGNOSTIC TROUBLE CODE CHART. Refer to  DIAGNOSTIC TROUBLE CODE CHART [08/2021 - ] 

Result: 

A 

See step  5

1. Read the Data List according to the display on the Techstream.

   Body Electrical > Back Door > Data List 

   Tester Display	Measurement Item	Range	Normal Condition	Diagnostic Note
   Pawl Switch	Luggage door closer assembly (pawl switch) signal	OFF or ON	OFF: Luggage door closer assembly except half-latched ON: Luggage door closer assembly half-latched	-

   Body Electrical > Back Door > Data List 

   Tester Display
   Pawl Switch

   OK

   The Data List display changes according to luggage compartment door operation.

   Result

   Proceed to
   OK
   NG

Result: 

NG 

See step  8

Result: 

OK 

See step  6

1. Remove the luggage door closer assembly.

   Refer to REMOVAL [06/2018 - ]

2. Inspect the luggage door closer assembly.

   Refer to INSPECTION [06/2018 - ]

   Result

   Proceed to
   OK
   NG

Result: 

NG 

REPLACE LUGGAGE DOOR CLOSER ASSEMBLY. Refer to  REMOVAL [06/2018 - ] 

Result: 

OK 

See step  7

1. Disconnect the R24 luggage closer motor assembly connector.
2. Measure the resistance according to the value(s) in the table below.

   Standard Resistance

   Tester Connection	Condition	Specified Condition
   R24-2 (LCM+) - R18-8 (M+)	Always	Below 1 Ω
   R24-1 (LCM-) - R18-1 (M-)	Always	Below 1 Ω
   R24-2 (LCM+) or R18-8 (M+) - Body ground	Always	10 kΩ or higher
   R24-1 (LCM-) or R18-1 (M-) - Body ground	Always	10 kΩ or higher

   Result

   Proceed to
   OK
   NG

Result: 

OK 

REPLACE LUGGAGE CLOSER MOTOR ASSEMBLY. Refer to  REMOVAL [08/2021 - ] 

Result: 

NG 

REPAIR OR REPLACE HARNESS OR CONNECTOR 

1. Remove the luggage door closer assembly.

   Refer to REMOVAL [06/2018 - ]

2. Inspect the luggage door closer assembly.

   Refer to INSPECTION [06/2018 - ]

   Result

   Proceed to
   OK
   NG

Result: 

NG 

REPLACE LUGGAGE DOOR CLOSER ASSEMBLY. Refer to  REMOVAL [06/2018 - ] 

Result: 

OK 

See step  9

1. Disconnect the R24 luggage closer motor assembly connector.
2. Disconnect the R18 luggage door closer assembly connector.
3. Measure the resistance according to the value(s) in the table below.

   Standard Resistance

   Tester Connection	Condition	Specified Condition
   R24-6 (SWG) - R18-12 (CSWE)	Always	Below 1 Ω
   R24-14 (PAWL) - R18-11 (CLS)	Always	Below 1 Ω
   R24-6 (SWG) or R18-12 (CSWE) - Body ground	Always	10 kΩ or higher
   R24-14 (PAWL) or R18-11 (CLS) - Body ground	Always	10 kΩ or higher

   Result

   Proceed to
   OK
   NG

Result: 

OK 

REPLACE LUGGAGE CLOSER MOTOR ASSEMBLY. Refer to  REMOVAL [08/2021 - ] 

Result: 

NG 

REPAIR OR REPLACE HARNESS OR CONNECTOR