LEMON Manuals: Even more car manuals for everyone
Home >> Lexus >> 2019 >> ES 350 Luxury >> Repair and Diagnosis >> External Pages >> Different car >> Section 11 (Front Camera System - Diagnostic Codes) >> Front Camera System >> DTC C1AAE-00: Front Recognition Camera Heater Malfunction [08/2021 - ] >> Procedure

DTC C1AAE-00: Front Recognition Camera Heater Malfunction [08/2021 - ]: Procedure

WARNING: This page does not describe the selected car, but rather 9 other vehicles, including the 2024 Lexus ES 350, 2024 Lexus ES 300h, 2024 Lexus ES 250, 2023 Lexus ES 350, and 2023 Lexus ES 300h. However, it is still accessible from the selected car via links, so may be relevant.
  1. CHECK FOR DTCs 
    1. Clear the DTCs.

      Chassis > Front Recognition Camera > Clear DTCs 

    2. Make sure that the DTC detection conditions are met.

      HINT: 

      If the detection conditions are not met, the system cannot detect the malfunction.

    3. Check for DTCs.

      Chassis > Front Recognition Camera > Trouble Codes 

      Result

      Result Proceed to
      DTC is not output A
      DTC is output B

    Result: 

    A 

    USE SIMULATION METHOD TO CHECK. Refer to  HOW TO PROCEED WITH TROUBLESHOOTING [06/2018 - ] 

    Result: 

    B 

    See step  2

  2. INSPECT FORWARD RECOGNITION WITH HEATER HOOD SUB-ASSEMBLY 
    1. Turn the ignition switch off.
    2. Disconnect the forward recognition with heater hood sub-assembly connector.
      GTY830995Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Component without harness connected
      (Forward Recognition with Heater Hood Sub-assembly)
    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      P14-1 (IG1) - P14-2 (HTR) Always 28.5 to 31.5 Ω

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPLACE FORWARD RECOGNITION WITH HEATER HOOD SUB-ASSEMBLY. Refer to  REMOVAL [06/2018 - ] 

    Result: 

    OK 

    See step  3

  3. CHECK HARNESS AND CONNECTOR (POWER SOURCE VOLTAGE) 
    GTY797433Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    *a Front view of wire harness connector
    (to Forward Recognition with Heater Hood Sub-assembly)
    1. Measure the voltage according to the value(s) in the table below.

      Standard Voltage

      Tester Connection Condition Specified Condition
      P14-1 (IG1) - Body ground Ignition switch ON 8 to 16 V
      Ignition switch off Below 1.5 V

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

    Result: 

    OK 

    See step  4

  4. CHECK HARNESS AND CONNECTOR (FORWARD RECOGNITION WITH HEATER HOOD SUB-ASSEMBLY - FORWARD RECOGNITION CAMERA) 
    1. Disconnect the P5 forward recognition camera connector.
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      P14-2 (HTR) - P5-1 (HTR) Always Below 1 Ω
      P14-2 (HTR) or P5-1 (HTR) - Body ground Always 10 kΩ or higher

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE FORWARD RECOGNITION CAMERA. Refer to  REMOVAL [08/2021 - ] 

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

scientia non olet · About LEMON Manuals