DTC U1000: CAN Communication Failure (Message Registry) [06/2018 - ]: Procedure

1. Choose the model to be inspected.

   Result

   Result	Proceed to
   For LED Type Turn Signal Light	A
   For Bulb Type Turn Signal Light	B

Result: 

B 

See step  4

Result: 

A 

See step  2

1. Connect the Techstream to the DLC3.
2. Turn the power switch on (IG).
3. Turn the Techstream on.
4. Enter the following menus: Body Electrical / AFS or AFS (Sub) / Trouble Codes.
5. Clear the DTCs.

   Body Electrical > AFS > Clear DTCs 

   Body Electrical > AFS (Sub) > Clear DTCs 

   Result

   Proceed to
   NEXT

Result: 

NEXT 

See step  3

1. Connect the Techstream to the DLC3.
2. Turn the power switch on (IG).
3. Turn the Techstream on.
4. Enter the following menus: Body Electrical / AFS or AFS (Sub) / Trouble Codes.
5. Check for DTCs.

   Body Electrical > AFS > Trouble Codes 

   Body Electrical > AFS (Sub) > Trouble Codes 

   OK

   DTC U1000 is not output.

   Result

   Result	Proceed to
   OK	A
   NG (DTC output from headlight ECU sub-assembly LH)	B
   NG (DTC output from headlight ECU sub-assembly RH)	C

Result: 

A 

USE SIMULATION METHOD TO CHECK. Refer to  HOW TO PROCEED WITH TROUBLESHOOTING [06/2018 - ] 

Result: 

B 

REPLACE HEADLIGHT ECU SUB-ASSEMBLY LH. Refer to  REMOVAL [06/2018 - 09/2022]  , or refer to  REMOVAL [09/2022 - ] 

Result: 

C 

REPLACE HEADLIGHT ECU SUB-ASSEMBLY RH. Refer to  REMOVAL [06/2018 - 09/2022]  , or refer to  REMOVAL [09/2022 - ] 

1. Connect the Techstream to the DLC3.
2. Turn the power switch on (IG).
3. Turn the Techstream on.
4. Enter the following menus: Body Electrical / HL AutoLeveling or HL AutoLeveling (Sub) / Trouble Codes.
5. Clear the DTCs.

   Body Electrical > HL AutoLeveling > Clear DTCs 

   Body Electrical > HL AutoLeveling (Sub) > Clear DTCs 

   Result

   Proceed to
   NEXT

Result: 

NEXT 

See step  5

1. Connect the Techstream to the DLC3.
2. Turn the power switch on (IG).
3. Turn the Techstream on.
4. Enter the following menus: Body Electrical / HL AutoLeveling or HL AutoLeveling (Sub) / Trouble Codes.
5. Check for DTCs.

   Body Electrical > HL AutoLeveling > Trouble Codes 

   Body Electrical > HL AutoLeveling (Sub) > Trouble Codes 

   OK

   DTC U1000 is not output.

   Result

   Result	Proceed to
   OK	A
   NG (DTC output from headlight ECU sub-assembly LH)	B
   NG (DTC output from headlight ECU sub-assembly RH)	C

Result: 

A 

USE SIMULATION METHOD TO CHECK. Refer to  HOW TO PROCEED WITH TROUBLESHOOTING [06/2018 - ] 

Result: 

B 

REPLACE HEADLIGHT ECU SUB-ASSEMBLY LH. Refer to  REMOVAL [06/2018 - 09/2022]  , or refer to  REMOVAL [09/2022 - ] 

Result: 

C 

REPLACE HEADLIGHT ECU SUB-ASSEMBLY RH. Refer to  REMOVAL [06/2018 - 09/2022]  , or refer to  REMOVAL [09/2022 - ]