LEMON Manuals: Even more car manuals for everyone
Home >> Lexus >> 2018 >> RX 450h Base >> Repair and Diagnosis >> Restraints >> Seat Belts >> Seat Belt (Service Information) >> Front Seat Outer Belt Assembly With Pre-TENSIONER >> Removal [08/2019 - ] >> Procedure

Removal [08/2019 - ]: Procedure

  1. PRECAUTION 
    NOTE:

    After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

    Refer to PRECAUTION [08/2019 - ]

  2. REMOVE DECK BOARD ASSEMBLY (w/o Rear No. 2 Seat) 

    Refer to PROCEDURE - Step 2

  3. REMOVE REAR DECK FLOOR BOX (w/o Rear No. 2 Seat) 

    Refer to PROCEDURE - Step 4

  4. REMOVE REAR NO. 4 FLOOR BOARD (w/ Rear No. 2 Seat) 

    Refer to PROCEDURE - Step 3

  5. REMOVE BATTERY SERVICE HOLE COVER (w/ Rear No. 2 Seat) 

    Refer to PROCEDURE - Step 4

  6. DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL 

    w/o Rear No. 2 Seat:

    Refer to PROCEDURE - Step 4

    w/ Rear No. 2 Seat:

    Refer to PROCEDURE - Step 5

    WARNING:
    • Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
    • If an SRS part is accidentally deployed, it may cause a serious injury.
    GTY684647Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  7. REMOVE FRONT DOOR SCUFF PLATE 

    Refer to PROCEDURE - Step 9

  8. REMOVE REAR DOOR SCUFF PLATE (w/o Rear No. 2 Seat) 

    Refer to PROCEDURE - Step 11

  9. REMOVE REAR DOOR SCUFF PLATE (w/ Rear No. 2 Seat) 

    Refer to PROCEDURE - Step 13

  10. REMOVE REAR DOOR INSIDE SCUFF PLATE (w/ Rear No. 2 Seat) 

    Refer to PROCEDURE - Step 14

  11. REMOVE LOWER CENTER PILLAR GARNISH 

    Refer to PROCEDURE - Step 12

  12. DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY 
    1. Remove the bolt and disconnect the floor anchor of the front seat outer belt assembly.
      GTY637898Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  13. REMOVE CENTER PILLAR GARNISH ASSEMBLY 

    Refer to PROCEDURE - Step 14

  14. REMOVE FRONT SEAT OUTER BELT ASSEMBLY 
    1. Remove the nut and disconnect the shoulder anchor of the front seat outer belt assembly.
      GTY621803Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Using a screwdriver, pull out the locking button as shown in the illustration to release the lock and disconnect the pretensioner connector.
      GTY624576Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Protective Tape
      *b Locking Button
      *c Release

      HINT: 

      Tape the screwdriver tip before use.

    3. Disconnect the connector.
    4. Remove the 2 bolts.
      GTY674544Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    5. Disengage the 2 guides to remove the front seat outer belt assembly.
  15. REMOVE FRONT SHOULDER BELT ANCHOR ADJUSTER ASSEMBLY 
    1. Remove the 2 bolts.
      GTY621804Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Disengage the guide to remove the front shoulder belt anchor adjuster assembly.
scientia non olet · About LEMON Manuals