LEMON Manuals: Even more car manuals for everyone
Home >> Lexus >> 2018 >> RX 450h Base >> Repair and Diagnosis (Single Page) >> Accessories & Equipment >> Infotainment >> Navigation System (Diagnostic Codes) (2 Of 2) & Symptom Tests (1 Of 2) >> Navigation System >> DTC B15C3: Speaker Output Short [08/2019 - ] >> Procedure

DTC B15C3: Speaker Output Short [08/2019 - ]: Procedure

  1. CHECK MODEL 
    1. Choose the model to be inspected.

      Result

      Result Proceed to
      for 9 Speakers A
      for 12 Speakers B
      for 15 Speakers C

    Result: 

    B 

    See step  11

    Result: 

    C 

    See step  21

    Result: 

    A 

    See step  2

  2. CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY, DCM (TELEMATICS TRANSCEIVER) OR SPEAKERS- BODY GROUND) 
    1. Disconnect the J66 stereo component amplifier assembly connector.
    2. Disconnect the J155 DCM (telematics transceiver) connector.
    3. Disconnect the K6 and K8 front No. 2 speaker assembly connectors.
    4. Disconnect the M3 and N3 front No. 1 speaker assembly connectors.
    5. Disconnect the O5 and P5 rear No. 2 speaker assembly connectors.
    6. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      J66-7 (CTR+) or J155-1 (SPI+) - Body ground Always 10 kΩ or higher
      J66-22 (CTR-) or J155-2 (SPI-) - Body ground Always 10 kΩ or higher
      J66-13 (FR+) or K6-4 - Body ground Always 10 kΩ or higher
      J66-28 (FR-) or K6-2 - Body ground Always 10 kΩ or higher
      J66-12 (FL+) or K8-4 - Body ground Always 10 kΩ or higher
      J66-27 (FL-) or K8-2 - Body ground Always 10 kΩ or higher
      J66-5 (WFR+) or M3-1 - Body ground Always 10 kΩ or higher
      J66-20 (WFR-) or M3-2 - Body ground Always 10 kΩ or higher
      J66-4 (WFL+) or N3-1 - Body ground Always 10 kΩ or higher
      J66-19 (WFL-) or N3-2 - Body ground Always 10 kΩ or higher
      J66-9 (RR+) or O5-4 (+TW) - Body ground Always 10 kΩ or higher
      J66-24 (RR-) or O5-2 (-TW) - Body ground Always 10 kΩ or higher
      J66-8 (RL+) or P5-4 (+TW) - Body ground Always 10 kΩ or higher
      J66-23 (RL-) or P5-2 (-TW) - Body ground Always 10 kΩ or higher

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

    Result: 

    OK 

    See step  3

  3. CHECK HARNESS AND CONNECTOR (DCM (TELEMATICS TRANSCEIVER) OR NO. 3 FRONT SPEAKER ASSEMBLY- BODY GROUND) 
    1. Disconnect the J155 DCM (telematics transceiver) connector.
    2. Disconnect the K2 front No. 3 speaker assembly connector.
    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      K2-2 or J155-3 (SPO+) - Body ground Always 10 kΩ or higher
      K2-1 or J155-4 (SPO-) - Body ground Always 10 kΩ or higher

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

    Result: 

    OK 

    See step  4

  4. INSPECT DCM (TELEMATICS TRANSCEIVER) 
    1. Remove the DCM (telematics transceiver).

      Refer to REMOVAL [08/2019 - ]

    2. Measure the resistance according to the value(s) in the table below.
      GTY843487Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Component without harness connected
      (DCM (Telematics Transceiver))

      Standard Resistance

      Tester Connection Condition Specified Condition
      1 (SPI+) - 3 (SPO+) Always Below 1 Ω
      2 (SPI-) - 4 (SPO-) Always Below 1 Ω
      1 (SPI+) - 2 (SPI-) Always 10 kΩ or higher
      3 (SPO+) - 4 (SPO-) Always 10 kΩ or higher
      1 (SPI+) or 3 (SPO+) - Body ground Always 10 kΩ or higher
      2 (SPI-) or 4 (SPO-) - Body ground Always 10 kΩ or higher

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPLACE DCM (TELEMATICS TRANSCEIVER). Refer to  REMOVAL [08/2019 - ] 

    Result: 

    OK 

    See step  5

  5. CHECK HARNESS AND CONNECTOR (REAR SPEAKER ASSEMBLY OR REAR NO. 2 SPEAKER ASSEMBLY - BODY GROUND) 
    1. Disconnect the O2 and P2 rear speaker assembly connectors.
    2. Disconnect the O5 and P5 rear No. 2 speaker assembly connectors.
    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      O2-1 or O5-3 (+) - Body ground Always 10 kΩ or higher
      O2-2 or O5-1 (-) - Body ground Always 10 kΩ or higher
      P2-1 or P5-3 (+) - Body ground Always 10 kΩ or higher
      P2-2 or P5-1 (-) - Body ground Always 10 kΩ or higher

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

    Result: 

    OK 

    See step  6

  6. INSPECT FRONT NO. 3 SPEAKER ASSEMBLY 
    1. Remove the front No. 3 speaker assembly.

      Refer to REMOVAL [10/2015 - ]

    2. Inspect the front No. 3 speaker assembly.

      Refer to INSPECTION [10/2015 - ]

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPLACE FRONT NO. 3 SPEAKER ASSEMBLY. Refer to  REMOVAL [10/2015 - ] 

    Result: 

    OK 

    See step  7

  7. INSPECT FRONT NO. 1 SPEAKER ASSEMBLY 
    1. Remove the front No. 1 speaker assembly.

      Refer to REMOVAL [10/2015 - ]

    2. Inspect the front No. 1 speaker assembly.

      Refer to INSPECTION [10/2015 - ]

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPLACE FRONT NO. 1 SPEAKER ASSEMBLY. Refer to  REMOVAL [10/2015 - ] 

    Result: 

    OK 

    See step  8

  8. INSPECT REAR SPEAKER ASSEMBLY 
    1. Remove the rear speaker assembly.

      Refer to REMOVAL [10/2015 - ]

    2. Inspect the rear speaker assembly.

      Refer to INSPECTION [10/2015 - ]

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPLACE REAR SPEAKER ASSEMBLY. Refer to  REMOVAL [10/2015 - ] 

    Result: 

    OK 

    See step  9

  9. INSPECT FRONT NO. 2 SPEAKER ASSEMBLY 
    1. Remove the front No. 2 speaker assembly.

      Refer to REMOVAL [10/2015 - ]

    2. Inspect the front No. 2 speaker assembly.

      Refer to INSPECTION [10/2015 - ]

    3. Clear the DTCs.

      Body Electrical > Navigation System > Clear DTCs 

    4. Recheck for DTCs and check that no DTCs are output.

      Body Electrical > Navigation System > Trouble Codes 

      OK

      No DTCs are output.

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    END 

    Result: 

    NG 

    See step  10

  10. REPLACE REAR NO. 2 SPEAKER ASSEMBLY 
    1. Remove the rear No. 2 speaker assembly.

      Refer to REMOVAL [10/2015 - ]

    2. Inspect the rear No. 2 speaker assembly.

      Refer to INSPECTION [10/2015 - ]

    3. Clear the DTCs.

      Body Electrical > Navigation System > Clear DTCs 

    4. Recheck for DTCs and check that no DTCs are output.

      Body Electrical > Navigation System > Trouble Codes 

      OK

      No DTCs are output.

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    END 

    Result: 

    NG 

    REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY. Refer to  REMOVAL [08/2019 - ] 

  11. CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY, DCM (TELEMATICS TRANSCEIVER) OR SPEAKERS - BODY GROUND) 
    1. Disconnect the J66 stereo component amplifier assembly connector.
    2. Disconnect the J155 DCM (telematics transceiver) connector.
    3. Disconnect the K5 and K7 front No. 2 speaker assembly connectors.
    4. Disconnect the M3 and N3 front No. 1 speaker assembly connectors.
    5. Disconnect the O5 and P5 rear No. 2 speaker assembly connectors.
    6. Disconnect the S53 rear No. 3 speaker assembly connector.
    7. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      J66-7 (CTR+) or J155-1 (SPI+) - Body ground Always 10 kΩ or higher
      J66-22 (CTR-) or J155-2 (SPI-) - Body ground Always 10 kΩ or higher
      J66-13 (FR+) or K5-2 - Body ground Always 10 kΩ or higher
      J66-28 (FR-) or K5-1 - Body ground Always 10 kΩ or higher
      J66-12 (FL+) or K7-2 - Body ground Always 10 kΩ or higher
      J66-27 (FL-) or K7-1 - Body ground Always 10 kΩ or higher
      J66-5 (WFR+) or M3-1 - Body ground Always 10 kΩ or higher
      J66-20 (WFR-) or M3-2 - Body ground Always 10 kΩ or higher
      J66-4 (WFL+) or N3-1 - Body ground Always 10 kΩ or higher
      J66-19 (WFL-) or N3-2 - Body ground Always 10 kΩ or higher
      J66-9 (RR+) or O5-4 (+TW) - Body ground Always 10 kΩ or higher
      J66-24 (RR-) or O5-2 (-TW) - Body ground Always 10 kΩ or higher
      J66-8 (RL+) or P5-4 (+TW) - Body ground Always 10 kΩ or higher
      J66-23 (RL-) or P5-2 (-TW) - Body ground Always 10 kΩ or higher
      J66-6 (WF1+) or S53-1 - Body ground Always 10 kΩ or higher
      J66-21 (WF1-) or S53-2 - Body ground Always 10 kΩ or higher

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

    Result: 

    OK 

    See step  12

  12. CHECK HARNESS AND CONNECTOR (DCM (TELEMATICS TRANSCEIVER) OR FRONT NO. 3 SPEAKER ASSEMBLY- BODY GROUND) 
    1. Disconnect the J155 DCM (telematics transceiver) connector.
    2. Disconnect the K2 front No. 3 speaker assembly connector.
    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      K2-2 or J155-3 (SPO+) - Body ground Always 10 kΩ or higher
      K2-1 or J155-4 (SPO-) - Body ground Always 10 kΩ or higher

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

    Result: 

    OK 

    See step  13

  13. INSPECT DCM (TELEMATICS TRANSCEIVER) 
    1. Remove the DCM (telematics transceiver).

      Refer to REMOVAL [08/2019 - ]

    2. Measure the resistance according to the value(s) in the table below.
      GTY843487Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Component without harness connected
      (DCM (Telematics Transceiver))

      Standard Resistance

      Tester Connection Condition Specified Condition
      1 (SPI+) - 3 (SPO+) Always Below 1 Ω
      2 (SPI-) - 4 (SPO-) Always Below 1 Ω
      1 (SPI+) - 2 (SPI-) Always 10 kΩ or higher
      3 (SPO+) - 4 (SPO-) Always 10 kΩ or higher
      1 (SPI+) or 3 (SPO+) - Body ground Always 10 kΩ or higher
      2 (SPI-) or 4 (SPO-) - Body ground Always 10 kΩ or higher

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPLACE DCM (TELEMATICS TRANSCEIVER). Refer to  REMOVAL [08/2019 - ] 

    Result: 

    OK 

    See step  14

  14. CHECK HARNESS AND CONNECTOR (REAR SPEAKER ASSEMBLY OR REAR NO. 2 SPEAKER ASSEMBLY - BODY GROUND) 
    1. Disconnect the O2 and P2 rear speaker assembly connectors.
    2. Disconnect the O5 and P5 rear No. 2 speaker assembly connectors.
    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      O2-1 or O5-3 (+) - Body ground Always 10 kΩ or higher
      O2-2 or O5-1 (-) - Body ground Always 10 kΩ or higher
      P2-1 or P5-3 (+) - Body ground Always 10 kΩ or higher
      P2-2 or P5-1 (-) - Body ground Always 10 kΩ or higher

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

    Result: 

    OK 

    See step  15

  15. INSPECT FRONT NO. 3 SPEAKER ASSEMBLY 
    1. Remove the front No. 3 speaker assembly.

      Refer to REMOVAL [10/2015 - ]

    2. Inspect the front No. 3 speaker assembly.

      Refer to INSPECTION [10/2015 - ]

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPLACE FRONT NO. 3 SPEAKER ASSEMBLY. Refer to  REMOVAL [10/2015 - ] 

    Result: 

    OK 

    See step  16

  16. INSPECT FRONT NO. 1 SPEAKER ASSEMBLY 
    1. Remove the front No. 1 speaker assembly.

      Refer to REMOVAL [10/2015 - ]

    2. Inspect the front No. 1 speaker assembly.

      Refer to INSPECTION [10/2015 - ]

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPLACE FRONT NO. 1 SPEAKER ASSEMBLY. Refer to  REMOVAL [10/2015 - ] 

    Result: 

    OK 

    See step  17

  17. INSPECT REAR SPEAKER ASSEMBLY 
    1. Remove the rear speaker assembly.

      Refer to REMOVAL [10/2015 - ]

    2. Inspect the rear speaker assembly.

      Refer to INSPECTION [10/2015 - ]

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPLACE REAR SPEAKER ASSEMBLY. Refer to  REMOVAL [10/2015 - ] 

    Result: 

    OK 

    See step  18

  18. INSPECT REAR NO. 3 SPEAKER ASSEMBLY 
    1. Remove the rear No. 3 speaker assembly.

      w/o Rear No. 2 Seat: Refer to REMOVAL [08/2019 - ]

      w/ Rear No. 2 Seat: Refer to REMOVAL [03/2018 - ]

    2. Inspect the rear No. 3 speaker assembly.

      w/o Rear No. 2 Seat: Refer to INSPECTION [10/2015 - ]

      w/ Rear No. 2 Seat: Refer to INSPECTION [03/2018 - ]

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPLACE REAR NO. 3 SPEAKER ASSEMBLY 

    w/o Rear No. 2 Seat: Refer to REMOVAL [08/2019 - ]

    w/ Rear No. 2 Seat: Refer to REMOVAL [03/2018 - ]

    Result: 

    OK 

    See step  19

  19. INSPECT REAR NO. 2 SPEAKER ASSEMBLY 
    1. Remove the rear No. 2 speaker assembly.

      Refer to REMOVAL [10/2015 - ]

    2. Inspect the rear No. 2 speaker assembly.

      Refer to INSPECTION [10/2015 - ]

    3. Clear the DTCs.

      Body Electrical > Navigation System > Clear DTCs 

    4. Recheck for DTCs and check that no DTCs are output.

      Body Electrical > Navigation System > Trouble Codes 

      OK

      No DTCs are output.

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    END 

    Result: 

    NG 

    See step  20

  20. REPLACE FRONT NO. 2 SPEAKER ASSEMBLY 
    1. Remove the front No. 2 speaker assembly.

      Refer to REMOVAL [10/2015 - ]

    2. Inspect the front No. 2 speaker assembly.

      Refer to INSPECTION [10/2015 - ]

    3. Clear the DTCs.

      Body Electrical > Navigation System > Clear DTCs 

    4. Recheck for DTCs and check that no DTCs are output.

      Body Electrical > Navigation System > Trouble Codes 

      OK

      No DTCs are output.

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    END 

    Result: 

    NG 

    REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY. Refer to  REMOVAL [08/2019 - ] 

  21. CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY, DCM (TELEMATICS TRANSCEIVER) OR SPEAKERS - BODY GROUND) 
    1. Disconnect the J66 stereo component amplifier assembly connector.
    2. Disconnect the J155 DCM (telematics transceiver) connector.
    3. Disconnect the K5 and K7 front No. 2 speaker assembly connectors.
    4. Disconnect the M3 and N3 front No. 1 speaker assembly connectors.
    5. Disconnect the O5 and P5 rear No. 2 speaker assembly connectors.
    6. Disconnect the S53 rear No. 3 speaker assembly connector.
    7. Disconnect the R25 and S38 quarter side speaker assembly connectors.
    8. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      J66-7 (CTR+) or J155-1 (SPI+) - Body ground Always 10 kΩ or higher
      J66-22 (CTR-) or J155-2 (SPI-) - Body ground Always 10 kΩ or higher
      J66-13 (FR+) or K5-2 - Body ground Always 10 kΩ or higher
      J66-28 (FR-) or K5-1 - Body ground Always 10 kΩ or higher
      J66-12 (FL+) or K7-2 - Body ground Always 10 kΩ or higher
      J66-27 (FL-) or K7-1 - Body ground Always 10 kΩ or higher
      J66-5 (WFR+) or M3-1 - Body ground Always 10 kΩ or higher
      J66-20 (WFR-) or M3-2 - Body ground Always 10 kΩ or higher
      J66-4 (WFL+) or N3-1 - Body ground Always 10 kΩ or higher
      J66-19 (WFL-) or N3-2 - Body ground Always 10 kΩ or higher
      J66-9 (RR+) or O5-4 (+TW) - Body ground Always 10 kΩ or higher
      J66-24 (RR-) or O5-2 (-TW) - Body ground Always 10 kΩ or higher
      J66-8 (RL+) or P5-4 (+TW) - Body ground Always 10 kΩ or higher
      J66-23 (RL-) or P5-2 (-TW) - Body ground Always 10 kΩ or higher
      J66-6 (WF1+) or S53-1 - Body ground Always 10 kΩ or higher
      J66-21 (WF1-) or S53-2 - Body ground Always 10 kΩ or higher
      J66-11 (SR+) or R25-2 - Body ground Always 10 kΩ or higher
      J66-26 (SR-) or R25-1 - Body ground Always 10 kΩ or higher
      J66-10 (SL+) or S38-2 - Body ground Always 10 kΩ or higher
      J66-25 (SL-) or S38-1 - Body ground Always 10 kΩ or higher

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

    Result: 

    OK 

    See step  22

  22. CHECK HARNESS AND CONNECTOR (DCM (TELEMATICS TRANSCEIVER) OR FRONT NO. 3 SPEAKER ASSEMBLY- BODY GROUND) 
    1. Disconnect the J155 DCM (telematics transceiver) connector.
    2. Disconnect the K2 front No. 3 speaker assembly connector.
    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      K2-2 or J155-3 (SPO+) - Body ground Always 10 kΩ or higher
      K2-1 or J155-4 (SPO-) - Body ground Always 10 kΩ or higher

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

    Result: 

    OK 

    See step  23

  23. INSPECT DCM (TELEMATICS TRANSCEIVER) 
    1. Remove the DCM (telematics transceiver).

      Refer to REMOVAL [08/2019 - ]

    2. Measure the resistance according to the value(s) in the table below.
      GTY843487Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Component without harness connected
      (DCM (Telematics Transceiver))

      Standard Resistance

      Tester Connection Condition Specified Condition
      1 (SPI+) - 3 (SPO+) Always Below 1 Ω
      2 (SPI-) - 4 (SPO-) Always Below 1 Ω
      1 (SPI+) - 2 (SPI-) Always 10 kΩ or higher
      3 (SPO+) - 4 (SPO-) Always 10 kΩ or higher
      1 (SPI+) or 3 (SPO+) - Body ground Always 10 kΩ or higher
      2 (SPI-) or 4 (SPO-) - Body ground Always 10 kΩ or higher

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPLACE DCM (TELEMATICS TRANSCEIVER). Refer to  REMOVAL [08/2019 - ] 

    Result: 

    OK 

    See step  24

  24. CHECK HARNESS AND CONNECTOR (REAR SPEAKER ASSEMBLY OR REAR NO. 2 SPEAKER ASSEMBLY - BODY GROUND) 
    1. Disconnect the O2 and P2 rear speaker assembly connectors.
    2. Disconnect the O5 and P5 rear No. 2 speaker assembly connectors.
    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      O2-1 or O5-3 (+) - Body ground Always 10 kΩ or higher
      O2-2 or O5-1 (-) - Body ground Always 10 kΩ or higher
      P2-1 or P5-3 (+) - Body ground Always 10 kΩ or higher
      P2-2 or P5-1 (-) - Body ground Always 10 kΩ or higher

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

    Result: 

    OK 

    See step  25

  25. INSPECT FRONT NO. 1 SPEAKER ASSEMBLY 
    1. Remove the front No. 1 speaker assembly.

      Refer to REMOVAL [10/2015 - ]

    2. Inspect the front No. 1 speaker assembly.

      Refer to INSPECTION [10/2015 - ]

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPLACE FRONT NO. 1 SPEAKER ASSEMBLY. Refer to  REMOVAL [10/2015 - ] 

    Result: 

    OK 

    See step  26

  26. INSPECT REAR SPEAKER ASSEMBLY 
    1. Remove the rear speaker assembly.

      Refer to REMOVAL [10/2015 - ]

    2. Inspect the rear speaker assembly.

      Refer to INSPECTION [10/2015 - ]

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPLACE REAR SPEAKER ASSEMBLY. Refer to  REMOVAL [10/2015 - ] 

    Result: 

    OK 

    See step  27

  27. INSPECT REAR NO. 3 SPEAKER ASSEMBLY 
    1. Remove the rear No. 3 speaker assembly.

      w/o Rear No. 2 Seat: Refer to REMOVAL [08/2019 - ]

      w/ Rear No. 2 Seat: Refer to REMOVAL [03/2018 - ]

    2. Inspect the rear No. 3 speaker assembly.

      w/o Rear No. 2 Seat: Refer to INSPECTION [10/2015 - ]

      w/ Rear No. 2 Seat: Refer to INSPECTION [03/2018 - ]

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPLACE REAR NO. 3 SPEAKER ASSEMBLY 

    w/o Rear No. 2 Seat: Refer to REMOVAL [08/2019 - ]

    w/ Rear No. 2 Seat: Refer to REMOVAL [03/2018 - ]

    Result: 

    OK 

    See step  28

  28. INSPECT QUARTER SIDE SPEAKER ASSEMBLY 
    1. Remove the quarter side speaker assembly.

      w/o Rear No. 2 Seat: Refer to REMOVAL [08/2019 - ]

      w/ Rear No. 2 Seat: Refer to REMOVAL [03/2018 - ]

    2. Inspect the quarter side speaker assembly.

      w/o Rear No. 2 Seat: Refer to INSPECTION [10/2015 - ]

      w/ Rear No. 2 Seat: Refer to INSPECTION [03/2018 - ]

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPLACE QUARTER SIDE SPEAKER ASSEMBLY 

    w/o Rear No. 2 Seat: Refer to REMOVAL [08/2019 - ]

    w/ Rear No. 2 Seat: Refer to REMOVAL [03/2018 - ]

    Result: 

    OK 

    See step  29

  29. INSPECT REAR NO. 2 SPEAKER ASSEMBLY 
    1. Remove the rear No. 2 speaker assembly.

      Refer to REMOVAL [10/2015 - ]

    2. Inspect the rear No. 2 speaker assembly.

      Refer to INSPECTION [10/2015 - ]

    3. Clear the DTCs.

      Body Electrical > Navigation System > Clear DTCs 

    4. Recheck for DTCs and check that no DTCs are output.

      Body Electrical > Navigation System > Trouble Codes 

      OK

      No DTCs are output.

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    END 

    Result: 

    NG 

    See step  30

  30. REPLACE FRONT NO. 2 SPEAKER ASSEMBLY 
    1. Remove the front No. 2 speaker assembly.

      Refer to REMOVAL [10/2015 - ]

    2. Inspect the front No. 2 speaker assembly.

      Refer to INSPECTION [10/2015 - ]

    3. Clear the DTCs.

      Body Electrical > Navigation System > Clear DTCs 

    4. Recheck for DTCs and check that no DTCs are output.

      Body Electrical > Navigation System > Trouble Codes 

      OK

      No DTCs are output.

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    END 

    Result: 

    NG 

    See step  31

  31. REPLACE FRONT NO. 3 SPEAKER ASSEMBLY 
    1. Remove the front No. 3 speaker assembly.

      Refer to REMOVAL [10/2015 - ]

    2. Inspect the front No. 3 speaker assembly.

      Refer to INSPECTION [10/2015 - ]

    3. Clear the DTCs.

      Body Electrical > Navigation System > Clear DTCs 

    4. Recheck for DTCs and check that no DTCs are output.

      Body Electrical > Navigation System > Trouble Codes 

      OK

      No DTCs are output.

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    END 

    Result: 

    NG 

    REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY. Refer to  REMOVAL [08/2019 - ] 

scientia non olet · About LEMON Manuals