Slip Indicator Light does not Come ON [03/2017 - ]: Procedure

1. Check if CAN communication system DTCs are output.

   Refer to DIAGNOSIS SYSTEM [03/2017 - 06/2019] , or refer to DIAGNOSIS SYSTEM [06/2019 - 04/2020] , or refer to DIAGNOSIS SYSTEM [04/2020 - 11/2021] , or refer to DIAGNOSIS SYSTEM [11/2021 - 10/2022] , or refer to DIAGNOSIS SYSTEM [10/2022 - 05/2023] , or refer to DIAGNOSIS SYSTEM [05/2023 - ]

   Result

   Result	Proceed to
   DTCs are not output.	A
   DTCs are output.	B

Result: 

B 

INSPECT CAN COMMUNICATION SYSTEM. Refer to  HOW TO PROCEED WITH TROUBLESHOOTING [03/2017 - 09/2018]  , or refer to  HOW TO PROCEED WITH TROUBLESHOOTING [09/2018 - 05/2023]  , or refer to  HOW TO PROCEED WITH TROUBLESHOOTING [05/2023 - ] 

Result: 

A 

See step  2

1. Connect the Techstream to the DLC3.
2. Turn the engine switch on (IG).
3. Select the Active Test on the Techstream.

   Refer to DATA LIST / ACTIVE TEST [03/2017 - 05/2023] , or refer to DATA LIST / ACTIVE TEST [05/2023 - ]

   Chassis > ABS/VSC/TRAC > Active Test 

   Tester Display	Measurement Item	Control Range	Diagnostic Note
   Slip Indicator Light	Slip indicator light	Indicator light ON/OFF	Observe combination meter assembly

   Chassis > ABS/VSC/TRAC > Active Test 

   Tester Display
   Slip Indicator Light

4. Select the Data List on the Techstream.

   Refer to DATA LIST / ACTIVE TEST [03/2017 - 05/2023] , or refer to DATA LIST / ACTIVE TEST [05/2023 - ]

   Chassis > ABS/VSC/TRAC > Data List 

   Tester Display	Measurement Item	Range	Normal Condition	Diagnostic Note
   Slip Indicator Light	Slip indicator light	ON or OFF	ON: Indicator light on OFF: Indicator light off	-

   Chassis > ABS/VSC/TRAC > Data List 

   Tester Display
   Slip Indicator Light

5. Check the operating condition of the slip indicator light when operating it using the Techstream.

   Result

   Result	Proceed to
   Slip indicator light in the Data List does not change using the Active Test.	A
   Slip indicator light in the Data List turns ON/OFF using the Active Test.	B

Result: 

A 

REPLACE SKID CONTROL ECU ASSEMBLY. Refer to  REMOVAL [03/2017 - 05/2023]  , or refer to  REMOVAL [05/2023 - ] 

Result: 

B 

See step  3

1. Turn the engine switch off.
2. Perform the Active Test of the combination meter assembly (meter CPU) using the Techstream.

   Refer to DATA LIST / ACTIVE TEST [03/2017 - ]

   Body Electrical > Combination Meter > Active Test 

   Tester Display
   Indicat. Lamp Slip

3. Check that the slip indicator light turns on or off in accordance with the Active Test.

   OK

   The slip indicator light turns on or off in accordance with the Techstream operation.

   Result

   Proceed to
   OK
   NG

Result: 

OK 

REPLACE SKID CONTROL ECU ASSEMBLY. Refer to  REMOVAL [03/2017 - 05/2023]  , or refer to  REMOVAL [05/2023 - ] 

Result: 

NG 

INSPECT METER / GAUGE SYSTEM. Refer to  HOW TO PROCEED WITH TROUBLESHOOTING [03/2017 - ]