DTC B15FE: XM Tuner Antenna Disconnected; DTC B15FF: XM Tuner Antenna Short [03/2017 - 05/2023]: Procedure

1. Check if the satellite radio antenna assembly cable is securely connected to the radio receiver assembly.

   OK

   Satellite radio antenna assembly cable is securely connected.

   Result

   Proceed to
   OK
   NG

Result: 

NG 

SECURELY CONNECT SATELLITE RADIO ANTENNA CABLE 

Result: 

OK 

See step  2

1. Clear the DTCs.

   Refer to DTC CHECK / CLEAR [03/2017 - 06/2019] , or refer to DTC CHECK / CLEAR [06/2019 - 04/2020] , or refer to DTC CHECK / CLEAR [04/2020 - 10/2022] , or refer to DTC CHECK / CLEAR [10/2022 - 05/2023]

   Body Electrical > Navigation System > Clear DTCs 

2. Recheck for DTCs and check that no DTCs are output.

   Refer to DTC CHECK / CLEAR [03/2017 - 06/2019] , or refer to DTC CHECK / CLEAR [06/2019 - 04/2020] , or refer to DTC CHECK / CLEAR [04/2020 - 10/2022] , or refer to DTC CHECK / CLEAR [10/2022 - 05/2023]

   Body Electrical > Navigation System > Trouble Codes 

   OK

   No DTCs are output.

   Result

   Proceed to
   OK
   NG

Result: 

OK 

USE SIMULATION METHOD TO CHECK. Refer to  HOW TO PROCEED WITH TROUBLESHOOTING [03/2017 - 04/2020]  , or refer to  HOW TO PROCEED WITH TROUBLESHOOTING [04/2020 - 05/2023] 

Result: 

NG 

See step  3

1. Disconnect the antenna connector from the No. 2 antenna cord sub-assembly.

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   *a	Front view of wire harness connector (to No. 2 Antenna Cord Sub-assembly)
   *b	Front view of wire harness connector (to Radio Receiver Assembly)

2. Disconnect the antenna connector from the radio receiver assembly.
3. Measure the resistance according to the value(s) in the table below.

   Standard Resistance

   Tester Connection	Condition	Specified Condition
   B-2 - C-1 (SXM)	Always	Below 1 Ω
   B-2a - C-1a	Always	Below 1 Ω
   B-2 or C-1 (SXM) - Body ground	Always	10 kΩ or higher
   B-2a or C-1a - Body ground	Always	10 kΩ or higher

   Result

   Proceed to
   OK
   NG

Result: 

NG 

REPLACE ANTENNA CORD SUB-ASSEMBLY. Refer to  REMOVAL [03/2017 - 06/2019]  , or refer to  REMOVAL [06/2019 - 05/2023] 

Result: 

OK 

See step  4

1. Disconnect the antenna connector from the wire harness.

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   *a	Front view of wire harness connector (to Wire Harness)
   *b	Front view of wire harness connector (to Antenna Cord Sub-assembly)

2. Disconnect the antenna connector from the antenna cord sub-assembly.
3. Measure the resistance according to the value(s) in the table below.

   Standard Resistance

   Tester Connection	Condition	Specified Condition
   X116-1 (SDARS) - B-2	Always	Below 1 Ω
   X116-1a - B-2a	Always	Below 1 Ω
   X116-1 (SDARS) or B-2 - Body ground	Always	10 kΩ or higher
   X116-1a or B-2a - Body ground	Always	10 kΩ or higher

   Result

   Proceed to
   OK
   NG

Result: 

NG 

REPLACE NO. 2 ANTENNA CORD SUB-ASSEMBLY. Refer to  REMOVAL [03/2017 - 06/2019]  , or refer to  REMOVAL [06/2019 - 05/2023] 

Result: 

OK 

See step  5

1. Disconnect the X116 No. 2 antenna cord sub-assembly connector.
2. Disconnect the X117 No. 6 antenna cord sub-assembly connector.
3. Measure the resistance according to the value(s) in the table below.

   Standard Resistance

   Tester Connection	Condition	Specified Condition
   X116-1 (SDARS) - X117-1 (SDARS)	Always	Below 1 Ω
   X116-1a - X117-1a	Always	Below 1 Ω
   X116-1 (SDARS) or X117-1 (SDARS) - Body ground	Always	10 kΩ or higher
   X116-1a or X117-1a - Body ground	Always	10 kΩ or higher

   Result

   Proceed to
   OK
   NG

Result: 

NG 

REPAIR OR REPLACE HARNESS OR CONNECTOR 

Result: 

OK 

See step  6

1. Disconnect the antenna connector from the satellite radio antenna assembly.

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   *a	Front view of wire harness connector (to Satellite Radio Antenna Assembly)
   *b	Front view of wire harness connector (to Wire Harness)

2. Disconnect the antenna connector from the wire harness.
3. Measure the resistance according to the value(s) in the table below.

   Standard Resistance

   Tester Connection	Condition	Specified Condition
   A-1 - X117-1 (SDARS)	Always	Below 1 Ω
   A-1a - X117-1a	Always	Below 1 Ω
   A-1 or X117-1 (SDARS) - Body ground	Always	10 kΩ or higher
   A-1a or X117-1a - Body ground	Always	10 kΩ or higher

   Result

   Proceed to
   OK
   NG

Result: 

NG 

REPLACE NO. 6 ANTENNA CORD SUB-ASSEMBLY. Refer to  REMOVAL [03/2017 - ] 

Result: 

OK 

See step  7

1. Replace the satellite radio antenna assembly with a new or known good one.

   Refer to REMOVAL [03/2017 - ]

2. Clear the DTCs.

   Refer to DTC CHECK / CLEAR [03/2017 - 06/2019] , or refer to DTC CHECK / CLEAR [06/2019 - 04/2020] , or refer to DTC CHECK / CLEAR [04/2020 - 10/2022] , or refer to DTC CHECK / CLEAR [10/2022 - 05/2023]

   Body Electrical > Navigation System > Clear DTCs 

3. Recheck for DTCs and check that no DTCs are output.

   Refer to DTC CHECK / CLEAR [03/2017 - 06/2019] , or refer to DTC CHECK / CLEAR [06/2019 - 04/2020] , or refer to DTC CHECK / CLEAR [04/2020 - 10/2022] , or refer to DTC CHECK / CLEAR [10/2022 - 05/2023]

   Body Electrical > Navigation System > Trouble Codes 

   OK

   No DTCs are output.

   Result

   Proceed to
   OK
   NG

Result: 

OK 

END (SATELLITE RADIO ANTENNA ASSEMBLY IS DEFECTIVE) 

Result: 

NG 

REPLACE RADIO RECEIVER ASSEMBLY. Refer to  REMOVAL [03/2017 - 05/2023]