LEMON Manuals: Even more car manuals for everyone
Home >> Lexus >> 2017 >> RC 300 F Sport >> Repair and Diagnosis >> External Pages >> Different car >> Section 57 (Automatic Transmission System (2GR-FKS,Aa81E) - Diagnostic Codes (4 Of 4) & Circuit Tests) >> AUTOMATIC TRANSMISSION SYSTEM (for 2GR-FKS) >> Transmission Control Switch Circuit [11/2017 - ] >> Procedure

Transmission Control Switch Circuit [11/2017 - ]: Procedure

WARNING: This page does not describe the selected car, but rather 7 other vehicles, including the 2024 Lexus RC 350, 2023 Lexus RC 350, 2022 Lexus RC 350, 2021 Lexus RC 350, and 2020 Lexus RC 350. However, it is still accessible from the selected car via links, so may be relevant.
  1. INSPECT TRANSMISSION CONTROL SWITCH (TRANSMISSION FLOOR SHIFT ASSEMBLY) 
    1. Disconnect the O77 transmission control switch (transmission floor shift assembly) connector.
    2. Measure the resistance according to the value(s) in the table below.
      GTY497942Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Component without harness connected
      (Transmission Control Switch (Transmission Floor Shift Assembly))

      Standard Resistance

      Tester Connection Condition Specified Condition
      4 (IG) - 5 (S) Shift lever in M, "+" and "-" Below 1 Ω
      Shift lever not in M, "+" and "-" 10 kΩ or higher
      3 (SFTU) - 2 (E) Shift lever held in "+" (Up-shift) Below 1 Ω
      Shift lever in M 10 kΩ or higher
      1 (SFTD) - 2 (E) Shift lever held in "-" (Down-shift) Below 1 Ω
      Shift lever in M 10 kΩ or higher

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPLACE TRANSMISSION CONTROL SWITCH (TRANSMISSION FLOOR SHIFT ASSEMBLY). Refer to  COMPONENTS [09/2014 - ] 

    Result: 

    OK 

    See step  2

  2. CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH - BATTERY, BODY GROUND) 
    1. Turn the engine switch on (IG).
    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage

      Tester Connection Condition Specified Condition
      O77-4 (IG) - Body ground Engine switch on (IG) 11 to 14 V
      Engine switch off Below 1 V
    3. Turn the engine switch off.
    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      O77-2 (E) - Body ground Always Below 1 Ω

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR (TRANSMISSION CONTROL SWITCH - BATTERY, BODY GROUND) 

    Result: 

    OK 

    See step  3

  3. CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH - ECM) 
    1. Connect the O77 transmission control switch (transmission floor shift assembly) connector.
    2. Disconnect the A91 ECM connector.
    3. Turn the engine switch on (IG).
    4. Measure the voltage according to the value(s) in the table below.

      Standard Voltage

      Tester Connection Condition Specified Condition
      A91-17 (S) - Body ground Shift lever in M, "+" and "-" 11 to 14 V
      Shift lever not in M, "+" and "-" Below 1 V
    5. Turn the engine switch off.
    6. Disconnect the spiral cable sub-assembly connector.
    7. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      A91-38 (SFTU) - Body ground Shift lever held in "+" (Up-shift) Below 1 Ω
      Shift lever in M 10 kΩ or higher
      A91-37 (SFTD) - Body ground Shift lever held in "-" (Down-shift) Below 1 Ω
      Shift lever in M 10 kΩ or higher

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE. Refer to  PROBLEM SYMPTOMS TABLE [11/2017 - ] 

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR (TRANSMISSION CONTROL SWITCH - ECM) 

scientia non olet · About LEMON Manuals