LEMON Manuals: Even more car manuals for everyone
Home >> Lexus >> 2017 >> RC 300 F Sport >> Repair and Diagnosis >> External Pages >> Different car >> Section 14 (Lighting System (Ext) - Diagnostic Codes & Circuit Tests) >> Lighting System >> DTC B243D: Left Low Beam Fan Malfunction; DTC B243E: Right Low Beam Fan Malfunction [10/2018 - ] >> Procedure

DTC B243D: Left Low Beam Fan Malfunction; DTC B243E: Right Low Beam Fan Malfunction [10/2018 - ]: Procedure

WARNING: This page does not describe the selected car, but rather 12 other vehicles, including the 2024 Lexus RC 350, 2024 Lexus RC 300, 2023 Lexus RC 350, 2023 Lexus RC 300, and 2022 Lexus RC 350. However, it is still accessible from the selected car via links, so may be relevant.
  1. CLEAR DTC 
    1. Connect the Techstream to the DLC3.
    2. Turn the engine switch on (IG).
    3. Turn the Techstream on.
    4. Enter the following menus: Body Electrical / HL AutoLeveling / Trouble Codes.
    5. Clear the DTCs.

      Body Electrical > HL AutoLeveling > Clear DTCs 

      Result

      Proceed to
      NEXT

    Result: 

    NEXT 

    See step  2

  2. CHECK FOR DTC 
    1. Connect the Techstream to the DLC3.
    2. Turn the engine switch on (IG).
    3. Operate the light control switch to turn on the low beam headlights and wait 120 seconds or more.
    4. Turn the Techstream on.
    5. Enter the following menus: Body Electrical / HL AutoLeveling / Trouble Codes.
    6. Check for DTCs.

      Body Electrical > HL AutoLeveling > Trouble Codes 

      OK

      DTC B243D and B243E are not output.

      Result

      Result Proceed to
      OK A
      NG (DTC B243D is output) B
      NG (DTC B243E is output) C

    Result: 

    A 

    USE SIMULATION METHOD TO CHECK. Refer to  HOW TO PROCEED WITH TROUBLESHOOTING [10/2018 - 11/2019]  , or refer to  HOW TO PROCEED WITH TROUBLESHOOTING [11/2019 - 09/2020]  , or refer to  HOW TO PROCEED WITH TROUBLESHOOTING [09/2020 - 10/2022]  , or refer to  HOW TO PROCEED WITH TROUBLESHOOTING [10/2022 - ] 

    Result: 

    C 

    See step  6

    Result: 

    B 

    See step  3

  3. CHECK HEADLIGHT UNIT LH 
    1. Interchange the headlight unit LH with RH and connect the connectors.

      Refer to DISASSEMBLY [10/2018 - ]

      Result

      Proceed to
      NEXT

    Result: 

    NEXT 

    See step  4

  4. CLEAR DTC 
    1. Connect the Techstream to the DLC3.
    2. Turn the engine switch on (IG).
    3. Turn the Techstream on.
    4. Enter the following menus: Body Electrical / HL AutoLeveling / Trouble Codes.
    5. Clear the DTCs.

      Body Electrical > HL AutoLeveling > Clear DTCs 

      Result

      Proceed to
      NEXT

    Result: 

    NEXT 

    See step  5

  5. CHECK FOR DTC 
    1. Connect the Techstream to the DLC3.
    2. Turn the engine switch on (IG).
    3. Operate the light control switch to turn on the low beam headlights and wait 120 seconds or more.
    4. Turn the Techstream on.
    5. Enter the following menus: Body Electrical / HL AutoLeveling / Trouble Codes.
    6. Check for DTCs.

      Body Electrical > HL AutoLeveling > Trouble Codes 

      Result

      Result Proceed to
      DTC B243D is output A
      DTC B243E is output B

    Result: 

    A 

    REPLACE NO. 1 HEADLIGHT ECU SUB-ASSEMBLY LH. Refer to  REMOVAL [10/2018 - ] 

    Result: 

    B 

    REPLACE HEADLIGHT UNIT LH. Refer to  DISASSEMBLY [10/2018 - ] 

  6. CHECK HEADLIGHT UNIT RH 
    1. Interchange the headlight unit RH with LH and connect the connectors.

      Refer to DISASSEMBLY [10/2018 - ]

      Result

      Proceed to
      NEXT

    Result: 

    NEXT 

    See step  7

  7. CLEAR DTC 
    1. Connect the Techstream to the DLC3.
    2. Turn the engine switch on (IG).
    3. Turn the Techstream on.
    4. Enter the following menus: Body Electrical / HL AutoLeveling / Trouble Codes.
    5. Clear the DTCs.

      Body Electrical > HL AutoLeveling > Clear DTCs 

      Result

      Proceed to
      NEXT

    Result: 

    NEXT 

    See step  8

  8. CHECK FOR DTC 
    1. Connect the Techstream to the DLC3.
    2. Turn the engine switch on (IG).
    3. Operate the light control switch to turn on the low beam headlights and wait 120 seconds or more.
    4. Turn the Techstream on.
    5. Enter the following menus: Body Electrical / HL AutoLeveling / Trouble Codes.
    6. Check for DTCs.

      Body Electrical > HL AutoLeveling > Trouble Codes 

      Result

      Result Proceed to
      DTC B243E is output A
      DTC B243D is output B

    Result: 

    A 

    REPLACE NO. 1 HEADLIGHT ECU SUB-ASSEMBLY RH. Refer to  REMOVAL [10/2018 - ] 

    Result: 

    B 

    REPLACE HEADLIGHT UNIT RH. Refer to  DISASSEMBLY [10/2018 - ] 

scientia non olet · About LEMON Manuals