LEMON Manuals: Even more car manuals for everyone
Home >> Lexus >> 2017 >> RC 300 F Sport >> Repair and Diagnosis >> External Pages >> Different car >> Section 1 (Automatic Transmission System (Aa81E) - Service Information (1 Of 2)) >> VALVE BODY ASSEMBLY (for 8AR-FTS) >> Inspection [10/2015 - ] >> Procedure

Inspection [10/2015 - ]: Procedure

WARNING: This page does not describe the selected car, but rather 19 other vehicles, including the 2024 Lexus RC 350, 2024 Lexus RC 300, 2023 Lexus RC 350, 2023 Lexus RC 300, and 2022 Lexus RC 350. However, it is still accessible from the selected car via links, so may be relevant.
  1. INSPECT SOLENOID (SL1) VALVE 
    GTY464575Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    *a Component without harness connected
    (Solenoid (SL1) Valve)
    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      1 - 2 20°C (68°F) 5.0 to 5.6 Ω
    2. Connect a positive (+) lead with a 21 W bulb from the battery to terminal 1 and a negative (-) lead to terminal 2 of the solenoid (SL1) valve connector and check the operation of the valve.

      OK

      The valve moves and makes an operating sound.

      If the result is not as specified, replace the solenoid (SL1) valve.

  2. INSPECT SOLENOID (SL2) VALVE 

    HINT: 

    Use the same procedure as for the solenoid (SL1) valve.

  3. INSPECT SOLENOID (SL3) VALVE 

    HINT: 

    Use the same procedure as for the solenoid (SL1) valve.

  4. INSPECT SOLENOID (SL4) VALVE 

    HINT: 

    Use the same procedure as for the solenoid (SL1) valve.

  5. INSPECT SOLENOID (SL5) VALVE 

    HINT: 

    Use the same procedure as for the solenoid (SL1) valve.

  6. INSPECT SOLENOID (SLU) VALVE 

    HINT: 

    Use the same procedure as for the solenoid (SL1) valve.

  7. INSPECT SOLENOID (SLT) VALVE 

    HINT: 

    Use the same procedure as for the solenoid (SL1) valve.

  8. INSPECT SOLENOID (SC1) VALVE 
    1. Measure the resistance according to the value(s) in the table below.
      GTY667245Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Component without harness connected
      (Solenoid (SC1) Valve)

      Standard Resistance

      Tester Connection Condition Specified Condition
      Solenoid (SC1) valve connector terminal - Solenoid (SC1) valve body 20°C (68°F) 11 to 15 Ω
    2. Connect a positive (+) lead from the battery to the terminal of the solenoid (SC1) valve connector, and a negative (-) lead to the solenoid (SC1) valve body, and check the operation of the valve.

      OK

      The valve moves and makes an operating sound.

      If the result is not as specified, replace the solenoid (SC1) valve.

  9. INSPECT SOLENOID (SC2) VALVE 

    HINT: 

    Use the same procedure as for the solenoid (SC1) valve.

  10. INSPECT ELECTROMAGNETIC OIL PUMP (w/ Stop And Start System) 
    1. Measure the resistance according to the value(s) in the table below.
      GTY635233Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Component without harness connected
      (Electromagnetic Oil Pump)

      Standard Resistance

      Tester Connection Condition Specified Condition
      1 - 2 20°C (68°F) 5.0 to 5.6 Ω

      If the result is not as specified, replace the electromagnetic oil pump.

scientia non olet · About LEMON Manuals