LEMON Manuals: Even more car manuals for everyone
Home >> Lexus >> 2017 >> RC 300 F Sport >> Repair and Diagnosis >> External Pages >> Different car >> Section 1 (Automatic Transmission System (Aa81E) - Service Information (1 Of 2)) >> Combination Switch >> Inspection [11/2017 - 09/2020] >> Procedure

Inspection [11/2017 - 09/2020]: Procedure

WARNING: This page does not describe the selected car, but rather 19 other vehicles, including the 2024 Lexus RC 350, 2024 Lexus RC 300, 2023 Lexus RC 350, 2023 Lexus RC 300, and 2022 Lexus RC 350. However, it is still accessible from the selected car via links, so may be relevant.
  1. INSPECT COMBINATION SWITCH ASSEMBLY 
    1. Inspect the ECO drive mode switch:
      1. Measure the resistance according to the value(s) in the table below.
        GTY513704Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
        *a Component without harness connected
        (Combination Switch Assembly)

        Standard Resistance

        Tester Connection Condition Specified Condition
        11 (ECO) - 16 (E) Combination switch assembly knob turned and held at ECO position Below 50 Ω
        Combination switch assembly knob not turned to ECO position 1 MΩ or higher

        If the result is not as specified, replace the combination switch assembly.

    2. Inspect NORMAL mode switch (w/o AVS):
      1. Measure the resistance according to the value(s) in the table below.

        Standard Resistance

        Tester Connection Condition Specified Condition
        9 (NORM) - 16 (E) Combination switch assembly knob pushed and held Below 50 Ω
        Combination switch assembly knob not pushed 1 MΩ or higher

        If the result is not as specified, replace the combination switch assembly.

        GTY513701Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
        *a Component without harness connected
        (Combination Switch Assembly)
    3. Inspect NORMAL or CUSTOMIZE mode switch (w/ AVS):
      1. Measure the resistance according to the value(s) in the table below.

        Standard Resistance

        Tester Connection Condition Specified Condition
        9 (NORM) - 16 (E) Combination switch assembly knob pushed and held Below 50 Ω
        Combination switch assembly knob not pushed 10 kΩ or higher

        If the result is not as specified, replace the combination switch assembly.

        GTY624148Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
        *a Component without harness connected
        (Combination Switch Assembly)
    4. Inspect the SPORT or SPORT S/S+ mode switch:
      1. Measure the resistance according to the value(s) in the table below.

        Standard Resistance

        Tester Connection Condition Specified Condition
        10 (PWR) - 16 (E) Combination switch assembly knob turned and held at SPORT or SPORT S/S+ position Below 50 Ω
        Combination switch assembly knob not turned to SPORT or SPORT S/S+ position 1 MΩ or higher

        If the result is not as specified, replace the combination switch assembly.

        GTY513700Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
        *a Component without harness connected
        (Combination Switch Assembly)
    5. Inspect the SNOW mode switch:
      1. Measure the resistance according to the value(s) in the table below.

        Standard Resistance

        Tester Connection Condition Specified Condition
        3 (SNSW) - 16 (E) SNOW mode switch pushed and held Below 50 Ω
        SNOW mode switch not pushed 1 MΩ or higher

        If the result is not as specified, replace the combination switch assembly.

        GTY513698Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
        *a Component without harness connected
        (Combination Switch Assembly)
    6. Inspect the VSC off mode switch:
      1. Measure the resistance according to the value(s) in the table below.

        Standard Resistance

        Tester Connection Condition Specified Condition
        1 (+) - 16 (E) VSC OFF mode switch pushed and held Below 50 Ω
        VSC OFF mode switch not pushed 1 MΩ or higher

        If the result is not as specified, replace the combination switch assembly.

        GTY513699Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
        *a Component without harness connected
        (Combination Switch Assembly)
    7. Check the illumination:
      1. Apply battery voltage to the combination switch assembly and check that the combination switch assembly illuminates.

        Standard

        Measurement Condition Specified Condition
        Battery positive (+) → 5 (ILL+) Battery negative (-) → 8 (ILL-) Illuminates

        If the result is not as specified, replace the combination switch assembly.

        GTY830517Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
        *a Component without harness connected
        (Combination Switch Assembly)
        *b Combination Switch Assembly Illumination
scientia non olet · About LEMON Manuals