LEMON Manuals: Even more car manuals for everyone
Home >> Lexus >> 2017 >> RC 300 F Sport >> Repair and Diagnosis >> External Pages >> Different car >> Section 1 (Automatic Transmission System (Aa81E) - Service Information (1 Of 2)) >> AUTOMATIC TRANSMISSION ASSEMBLY (for 2GR) >> Removal [11/2017 - ] >> Procedure

Removal [11/2017 - ]: Procedure

WARNING: This page does not describe the selected car, but rather 19 other vehicles, including the 2024 Lexus RC 350, 2024 Lexus RC 300, 2023 Lexus RC 350, 2023 Lexus RC 300, and 2022 Lexus RC 350. However, it is still accessible from the selected car via links, so may be relevant.
  1. PRECAUTION 
    NOTE:

    After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

    Refer to PRECAUTION [11/2017 - 09/2020] , or refer to PRECAUTION [09/2020 - ]

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL 
    NOTE:

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Refer to INITIALIZATION [11/2017 - 10/2018] , or refer to INITIALIZATION [10/2018 - 09/2020] , or refer to INITIALIZATION [09/2020 - 10/2022] , or refer to INITIALIZATION [10/2022 - 10/2023] , or refer to INITIALIZATION [10/2023 - ]

  3. REMOVE INTAKE AIR SURGE TANK ASSEMBLY 

    Refer to REMOVAL [11/2017 - ]

  4. REMOVE NO. 1 ENGINE UNDER COVER ASSEMBLY 

    Refer to PROCEDURE - Step 11

  5. REMOVE FRONT SUSPENSION MEMBER BRACE 

    Refer to PROCEDURE - Step 14

  6. DRAIN ENGINE COOLANT 

    Refer to PROCEDURE - Step 2

  7. DRAIN AUTOMATIC TRANSMISSION FLUID 

    See step  2

  8. REMOVE PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY 

    Refer to REMOVAL [09/2014 - ]

  9. REMOVE EXHAUST MANIFOLD 

    Refer to REMOVAL [11/2017 - ]

  10. REMOVE STARTER COVER 

    Refer to PROCEDURE - Step 4

  11. REMOVE STARTER ASSEMBLY 

    Refer to PROCEDURE - Step 5

  12. REMOVE FLYWHEEL HOUSING SIDE COVER 
    1. Remove the flywheel housing side cover from the engine assembly.
      GTY294267Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  13. REMOVE DRIVE PLATE AND TORQUE CONVERTER ASSEMBLY SETTING BOLT 
    1. Using SST, hold the crankshaft pulley.
      • SST: 09213-7001109330-00021 
        1. 09213-70020
      GTY464035Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Remove the 6 drive plate and torque converter assembly setting bolts.
      GTY291116Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      HINT: 

      There will be one black colored bolt.

  14. REMOVE FLOOR SHIFT GEAR SHIFTING ROD SUB-ASSEMBLY 
    1. Move the shift lever to N.
    2. Remove the nut and disconnect the floor shift gear shifting rod sub-assembly from the lever of the transmission floor shift assembly.
      GTY462357Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Lever
    3. Remove the clip, pin and floor shift gear shifting rod sub-assembly from the transmission control shaft lever RH.
      GTY508299Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Pin
  15. SUPPORT AUTOMATIC TRANSMISSION ASSEMBLY 
    1. Support the automatic transmission assembly with a transmission jack.
      NOTE:
      • In order to protect the automatic transmission oil pan sub-assembly, place attachments on the transmission jack.
      • Make sure that the attachments and automatic transmission oil pan sub-assembly are centered on the transmission jack.
      • To prevent the automatic transmission oil pan sub-assembly from being deformed, do not place any attachments under the automatic transmission oil pan sub-assembly.
      GTY469011Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  16. REMOVE REAR ENGINE MOUNTING MEMBER 
    1. Remove the 4 bolts and disconnect the rear engine mounting member from the vehicle body.
      GTY502781Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Remove the 4 nuts and rear engine mounting member from the rear No. 1 engine mounting insulator.
      GTY518663Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  17. DISCONNECT NO. 2 EARTH WIRE 
    1. Remove the bolt and disconnect the No. 2 earth wire from the automatic transmission assembly.
      GTY457370Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  18. DISCONNECT WIRE HARNESS 
    1. Tilt down the automatic transmission assembly.
      NOTE:

      Make sure that the engine assembly does not contact the vehicle body when tilting the automatic transmission assembly.

      GTY458347Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Disconnect the park/neutral position switch assembly connector.
      GTY512382Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Park/Neutral Position Switch Assembly Connector *b Transmission Wire Connector
      *c Nut *d Breather Plug Hose
    3. Disconnect the transmission wire connector.

      HINT: 

      Disengage the claw, pull down the lever, and then disconnect the transmission wire connector.

    4. Disengage the 4 clamps.
    5. Disconnect the breather plug hose from the wire harness.
    6. Remove the nut and wire harness from the automatic transmission assembly.
  19. DISCONNECT WATER BY-PASS HOSE 
    1. Remove the bolt to disconnect the hose clamp from the automatic transmission assembly.
      GTY508631Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *1 Hose Clamp
    2. Slide the 2 clips and disconnect the water by-pass hose and No. 2 water by-pass hose from the transmission oil cooler.

      HINT: 

      Use a container to catch any coolant that flows out of the water by-pass hose and No. 2 water by-pass hose.

  20. REMOVE AUTOMATIC TRANSMISSION ASSEMBLY 
    1. Remove the 9 bolts and automatic transmission assembly from the engine assembly.
      NOTE:
      • Secure the automatic transmission assembly to the transmission jack using a belt, etc. to prevent it from falling.
      • To prevent damage to the 2 knock pins, do not pry between the automatic transmission assembly and engine assembly.
      GTY460717Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  21. REMOVE REAR ENGINE MOUNTING INSULATOR ASSEMBLY 
    1. Remove the 4 bolts and rear engine mounting insulator assembly from the automatic transmission assembly.
      GTY457372Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  22. REMOVE TORQUE CONVERTER ASSEMBLY 
    1. Put matchmarks on the automatic transmission case sub-assembly and the torque converter assembly.
      GTY458099Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Matchmark
    2. Remove the torque converter assembly from the automatic transmission assembly.
  23. INSPECT TORQUE CONVERTER ASSEMBLY 

    Refer to INSPECTION [11/2017 - ]

scientia non olet · About LEMON Manuals