Engine Oil Level Sensor Circuit [11/2021 - ]: Procedure

1. Connect the Techstream to the DLC3.
2. Turn the engine switch on (IG).
3. Turn the Techstream on.
4. Enter the following menus: Body Electrical / Combination Meter / Data List.
5. Read the Data List according to the display on the Techstream.

   Body Electrical > Combination Meter > Data List 

   Tester Display	Measurement Item	Range	Normal Condition	Diagnostic Note
   Oil Level SW	Engine oil level sensor	OFF or ON	OFF: Engine oil level not low ON: Engine oil level low	-

   Body Electrical > Combination Meter > Data List 

   Tester Display
   Oil Level SW

   Result

   Result	Proceed to
   The Data List item changes correctly	A
   The Data List item do not change correctly	B

Result: 

A 

REPLACE COMBINATION METER ASSEMBLY. Refer to  REMOVAL [09/2020 - ] 

Result: 

B 

See step  2

1. Confirm the vehicle type.

   Result

   Result	Proceed to
   for 2GR-FKS	A
   for 8AR-FTS	B
   for 2UR-GSE	C

Result: 

B 

See step  5

Result: 

C 

See step  6

Result: 

A 

See step  3

1. Remove the engine oil level sensor.

   for 2GR-FKS: Refer to REMOVAL [10/2017 - ]

2. Inspect the engine oil level sensor.

   for 2GR-FKS: Refer to INSPECTION [10/2017 - ]

   Result

   Proceed to
   OK
   NG

Result: 

NG 

REPLACE ENGINE OIL LEVEL SENSOR 

for 2GR-FKS: Refer to REMOVAL [10/2017 - ]

Result: 

OK 

See step  4

1. Disconnect the K3 combination meter assembly connector.
2. Measure the resistance according to the value(s) in the table below.

   Standard Resistance

   Tester Connection	Condition	Specified Condition
   F117-1 (LOIL) - K3-15 (OILW)	Always	Below 1 Ω
   F117-1 (LOIL) or K3-15 (OILW) - Body ground	Always	10 kΩ or higher

   Result

   Proceed to
   OK
   NG

Result: 

OK 

REPLACE COMBINATION METER ASSEMBLY. Refer to  REMOVAL [09/2020 - ] 

Result: 

NG 

REPAIR OR REPLACE HARNESS OR CONNECTOR 

1. Remove the engine oil level sensor.

   for 8AR-FTS: Refer to REMOVAL [10/2016 - ]

2. Inspect the engine oil level sensor.

   for 8AR-FTS: Refer to INSPECTION [08/2015 - ]

   Result

   Proceed to
   OK
   NG

Result: 

OK 

See step  7

Result: 

NG 

REPLACE ENGINE OIL LEVEL SENSOR 

for 8AR-FTS: Refer to REMOVAL [10/2016 - ]

1. Remove the engine oil level sensor.

   for 2GR-FKS: Refer to REMOVAL [11/2021 - ]

2. Inspect the engine oil level sensor.

   for 2GR-FKS: Refer to INSPECTION [11/2021 - ]

   Result

   Proceed to
   OK
   NG

Result: 

NG 

REPLACE ENGINE OIL LEVEL SENSOR 

for 2GR-FKS: Refer to REMOVAL [11/2021 - ]

Result: 

OK 

See step  7

1. Disconnect the K3 combination meter assembly connector.
2. Measure the resistance according to the value(s) in the table below.

   Standard Resistance

   Tester Connection	Condition	Specified Condition
   F64-1 (LOIL) - K3-15 (OILW)	Always	Below 1 Ω
   F64-1 (LOIL) or K3-15 (OILW) - Body ground	Always	10 kΩ or higher
   F64-2 (GND) - Body ground	Always	Below 1 Ω

   Result

   Proceed to
   OK
   NG

Result: 

OK 

REPLACE COMBINATION METER ASSEMBLY. Refer to  REMOVAL [09/2020 - ] 

Result: 

NG 

REPAIR OR REPLACE HARNESS OR CONNECTOR