LEMON Manuals: Even more car manuals for everyone
Home >> Lexus >> 2017 >> IS 300 F Sport >> Repair and Diagnosis >> External Pages >> Different car >> Section 6 (Automatic Transmission System (Aa81E) - Service Information (1 Of 2)) >> Combination Switch >> Inspection [09/2020 - ] >> Procedure

Inspection [09/2020 - ]: Procedure

WARNING: This page does not describe the selected car, but rather 20 other vehicles, including the 2024 Lexus IS 350, 2024 Lexus IS 300, 2023 Lexus IS 350, 2023 Lexus IS 300, and 2022 Lexus IS 350. However, it is still accessible from the selected car via links, so may be relevant.
  1. INSPECT COMBINATION SWITCH ASSEMBLY 
    1. Inspect the Eco mode switch:
      1. Measure the resistance according to the value(s) in the table below.
        GTY466580Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
        *a Component without harness connected
        (Combination Switch Assembly)

        Standard Resistance

        Tester Connection Condition Specified Condition
        11 (ECO) - 16 (E) Combination switch assembly knob turned and held at Eco position Below 50 Ω
        Combination switch assembly knob not turned to Eco position 1 MΩ or higher

        If the result is not as specified, replace the combination switch assembly.

    2. Inspect the Normal or Normal/Custom mode switch:
      1. Measure the resistance according to the value(s) in the table below.
        GTY624148Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
        *a Component without harness connected
        (Combination Switch Assembly)

        Standard Resistance

        Tester Connection Condition Specified Condition
        9 (NORM) - 16 (E) Combination switch assembly knob pushed and held Below 50 Ω
        Combination switch assembly knob not pushed 1 MΩ or higher

        If the result is not as specified, replace the combination switch assembly.

    3. Inspect the Sport or Sport S/S+ mode switch:
      1. Measure the resistance according to the value(s) in the table below.
        GTY470806Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
        *a Component without harness connected
        (Combination Switch Assembly)

        Standard Resistance

        Tester Connection Condition Specified Condition
        10 (PWR) - 16 (E) Combination switch assembly knob turned and held at Sport or Sport S/S+ position Below 50 Ω
        Combination switch assembly knob not turned to Sport or Sport S/S+ position 1 MΩ or higher

        If the result is not as specified, replace the combination switch assembly.

    4. Inspect the SNOW mode switch:
      1. Measure the resistance according to the value(s) in the table below.
        GTY466582Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
        *a Component without harness connected
        (Combination Switch Assembly)

        Standard Resistance

        Tester Connection Condition Specified Condition
        3 (SNSW) - 16 (E) SNOW mode switch pushed and held Below 50 Ω
        SNOW mode switch not pushed 1 MΩ or higher

        If the result is not as specified, replace the combination switch assembly.

    5. Inspect the VSC OFF switch:
      1. Measure the resistance according to the value(s) in the table below.
        GTY466583Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
        *a Component without harness connected
        (Combination Switch Assembly)

        Standard Resistance

        Tester Connection Condition Specified Condition
        1 (+) - 16 (E) VSC OFF switch pushed and held Below 50 Ω
        VSC OFF switch not pushed 1 MΩ or higher

        If the result is not as specified, replace the combination switch assembly.

    6. Inspect the BRAKE HOLD switch:
      1. Measure the resistance according to the value(s) in the table below.
        GTY954377Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
        *a Component without harness connected
        (Combination Switch Assembly)

        Standard Resistance

        Tester Connection Condition Specified Condition
        14 (+B) - 16 (E) BRAKE HOLD switch pushed and held Below 50 Ω
        BRAKE HOLD switch not pushed 1 MΩ or higher

        If the result is not as specified, replace the combination switch assembly.

    7. Check the illumination:
      1. Apply battery voltage between the terminals of the switch, and check the illumination condition of the combination switch assembly.
        GTY958568Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
        *a Component without harness connected
        (Combination Switch Assembly)
        *b Illumination

        Standard

        Measurement Condition Specified Condition
        Battery positive (+) → 5 (ILL+)
        Battery negative (-) → 8 (ILL-)        		 Illuminates

        If the result is not as specified, replace the combination switch assembly.

scientia non olet · About LEMON Manuals