LEMON Manuals: Even more car manuals for everyone
Home >> Lexus >> 2017 >> IS 300 F Sport >> Repair and Diagnosis >> External Pages >> Different car >> Section 46 (Engine Control System (8AR-FTS) - Diagnostic Codes (14 Of 14) & Symptom Tests (1 Of 4)) >> SFI System >> DTC P2A00-26: O2 Sensor Circuit Range/Performance Bank 1 Sensor 1 Signal Rate of Change Below Threshold [09/2022 - ] >> Confirmation Driving Pattern

Confirmation Driving Pattern

WARNING: This page does not describe the selected car, but rather 9 other vehicles, including the 2024 Lexus IS 300, 2023 Lexus IS 300, 2022 Lexus IS 300, 2021 Lexus IS 300, and 2020 Lexus IS 300. However, it is still accessible from the selected car via links, so may be relevant.

HINT: 

Performing this confirmation driving pattern will activate the air fuel ratio sensor response monitor.

GTY1138291Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  1. Connect the GTS to the DLC3.
  2. Turn the engine switch on (IG).
  3. Turn the GTS on.
  4. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
  5. Turn the engine switch off and wait for at least 30 seconds.
  6. Turn the engine switch on (IG) and turn the GTS on.
  7. Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) or higher [A].
  8. Drive the vehicle at a speed of approximately 60 km/h (37 mph) for 10 minutes or more in a city area [B].
    WARNING:

    When performing the confirmation driving pattern, obey all speed limits and traffic laws.

  9. Enter the following menus: Powertrain / Engine / Trouble Codes [C].
  10. Read the pending DTCs.

    HINT: 

    • If a pending DTC is output, the system is malfunctioning.
    • If a pending DTC is not output, perform the following procedure.
  11. Enter the following menus: Powertrain / Engine / Utility / All Readiness.
  12. Input the DTC: P2A00-26.
  13. Check the DTC judgment result.
    GTS Display Description
    NORMAL
    • DTC judgment completed
    • System normal
    ABNORMAL
    • DTC judgment completed
    • System abnormal
    INCOMPLETE
    • DTC judgment not completed
    • Perform driving pattern after confirming DTC enabling conditions
    N/A
    • Unable to perform DTC judgment
    • Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    HINT: 

    • If the judgment result shows NORMAL, the system is normal.
    • If the judgment result shows ABNORMAL, the system has a malfunction.
    • If the judgment result shows INCOMPLETE or N/A and no pending DTC is output, perform the following procedure.
  14. Drive the vehicle at a speed between 75 and 100 km/h (47 and 62 mph) for 10 minutes [D].
    WARNING:

    When performing the confirmation driving pattern, obey all speed limits and traffic laws.

  15. Enter the following menus: Powertrain / Engine / Trouble Codes [E].
  16. Read the pending DTCs.

    HINT: 

    • If a pending DTC is output, the system is malfunctioning.
    • If a pending DTC is not output, perform the following procedure.
  17. Enter the following menus: Powertrain / Engine / Utility / All Readiness.
  18. Input the DTC: P2A00-26.
  19. Check the DTC judgment result.
    GTS Display Description
    NORMAL
    • DTC judgment completed
    • System normal
    ABNORMAL
    • DTC judgment completed
    • System abnormal
    INCOMPLETE
    • DTC judgment not completed
    • Perform driving pattern after confirming DTC enabling conditions
    N/A
    • Unable to perform DTC judgment
    • Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    HINT: 

    • If the judgment result shows NORMAL, the system is normal.
    • If the judgment result shows ABNORMAL, the system has a malfunction.
    • If the judgment result shows INCOMPLETE or N/A, drive the vehicle again under an increased load and then recheck the judgment result.
scientia non olet · About LEMON Manuals