Turn Signal Switch Circuit [09/2020 - ]: Procedure

1. Connect the Techstream to the DLC3.
2. Turn the engine switch on (IG).
3. Turn the Techstream on.
4. Enter the following menus: Body Electrical / Combination Meter / Data List.
5. Read the Data List according to the display on the Techstream.

   Body Electrical > Combination Meter > Data List 

   Tester Display	Measurement Item	Range	Normal Condition	Diagnostic Note
   Turn Signal Switch (Right)	Turn signal switch (right) signal	OFF or ON	OFF: Turn signal switch not in right turn position ON: Turn signal switch in right turn position	-
   Turn Signal Switch (Left)	Turn signal switch (left) signal	OFF or ON	OFF: Turn signal switch not in left turn position ON: Turn signal switch in left turn position	-

   Body Electrical > Combination Meter > Data List 

   Tester Display
   Turn Signal Switch (Right)
   Turn Signal Switch (Left)

   OK

   Normal conditions listed above are displayed.

   Result

   Proceed to
   OK
   NG

Result: 

OK 

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE. Refer to  PROBLEM SYMPTOMS TABLE [09/2020 - 11/2021]  , or refer to  PROBLEM SYMPTOMS TABLE [11/2021 - ] 

Result: 

NG 

See step  2

1. Remove the headlight dimmer switch assembly.

   Refer to REMOVAL [04/2013 - ]

2. Inspect the headlight dimmer switch assembly.

   Refer to INSPECTION [09/2020 - ]

   Result

   Proceed to
   OK
   NG

Result: 

NG 

REPLACE HEADLIGHT DIMMER SWITCH ASSEMBLY. Refer to  REMOVAL [04/2013 - ] 

Result: 

OK 

See step  3

1. Disconnect the K24 windshield wiper switch assembly connector.
2. Measure the resistance according to the value(s) in the table below.

   Standard Resistance

   Tester Connection	Condition	Specified Condition
   K23-16 (E) - K24-6 (GND1)	Always	Below 1 Ω
   K23-14 (TL) - K24-13 (TL1)	Always	Below 1 Ω
   K23-15 (TR) - K24-14 (TR1)	Always	Below 1 Ω
   K23-17 (CR) - K24-12 (CR1)	Always	Below 1 Ω
   K23-16 (E) or K24-6 (GND1) - Body ground)	Always	10 kΩ or higher
   K23-14 (TL) or K24-13 (TL1) - Body ground	Always	10 kΩ or higher
   K23-15 (TR) or K24-14 (TR1) - Body ground)	Always	10 kΩ or higher
   K23-17 (CR) or K24-12 (CR1) - Body ground	Always	10 kΩ or higher

   Result

   Proceed to
   OK
   NG

Result: 

NG 

REPAIR OR REPLACE HARNESS OR CONNECTOR 

Result: 

OK 

See step  4

1. Disconnect the K4 combination meter assembly connector.
2. Measure the resistance according to the value(s) in the table below.

   Standard Resistance

   Tester Connection	Condition	Specified Condition
   K24-16 (TR2) - K4-3 (ER)	Always	Below 1 Ω
   K24-17 (TL2) - K4-4 (EL)	Always	Below 1 Ω
   K24-16 (TR2) or K4-3 (ER) - Body ground	Always	10 kΩ or higher
   K24-17 (TL2) or K4-4 (EL) - Body ground	Always	10 kΩ or higher

   Result

   Proceed to
   OK
   NG

Result: 

OK 

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE. Refer to  PROBLEM SYMPTOMS TABLE [09/2020 - 11/2021]  , or refer to  PROBLEM SYMPTOMS TABLE [11/2021 - ] 

Result: 

NG 

REPAIR OR REPLACE HARNESS OR CONNECTOR