DTC P2807-7F: Pressure Control Solenoid "G" Actuator Stuck Off [10/2017 - 09/2019]: Description

WARNING: This page does not describe the selected car, but rather 7 other vehicles, including the 2024 Lexus IS 350, 2023 Lexus IS 350, 2022 Lexus IS 350, 2021 Lexus IS 350, and 2020 Lexus IS 350. However, it is still accessible from the selected car via links, so may be relevant.

Based on signals from the transmission revolution sensors (NT, SP2 and NC3), the actual gear is detected.

If the detected gear is different than the commanded gear, the ECM detects related mechanical problems in the shift solenoid valves, transmission valve body assembly and automatic transmission assembly.

HINT:

ACTUAL GEAR WHEN A PROBLEM OCCURS IN SHIFT SOLENOID VALVE SL4:

ECM commanded gear	1st	2nd	3rd	4th	5th	6th	7th	8th
Actual gear during SL4 stuck ON malfunction	4th	4th	3rd	4th	6th	6th	7th	6th
Actual gear during SL4 stuck OFF malfunction	1st	2nd	3rd	N (1st)*	5th	N*	7th	8th

*: Neutral

DTC No.	Detection Item	DTC Detection Condition	Trouble Area	MIL	Memory	Note
P2807-7F	Pressure Control Solenoid "G" Actuator Stuck Off	All of the following conditions are met (2-trip detection logic): Engine coolant temperature is 40°C (104°F) or higher. ATF temperature is -10°C (14°F) or higher. The vehicle is driven with the shift lever in D. No malfunctions are detected in the shift solenoid valve SL1, SL2, SL3, SL4, SL5 and SR, transmission revolution sensors (NT, NC3 and SP2), oil pressure switch, engine coolant temperature sensor, ATF temperature sensor, knock control sensor, electronic throttle and CAN communication system. Either of the following conditions is met: Any of the following conditions are met 2 times: When gear shifts to 1st are requested by the ECM, actual gear changes to 4th gear. When gear shifts to 2nd are requested by the ECM, actual gear changes to 4th gear. When gear shifts to 5th are requested by the ECM, actual gear changes to 6th gear. When gear shifts to 8th are requested by the ECM, actual gear changes to 6th gear. When gear shifts to 4th or 6th are requested by the ECM, the engine speed overruns (neutral status) for 0.5 seconds or more.	DTC Detection Condition 1, 2, 3, 4 and 5 (a): Shift solenoid valve SL4 Transmission valve body assembly Torque converter assembly Automatic transmission assembly DTC Detection Condition 1, 2, 3, 4 and 5 (b): Shift solenoid valve SL4 Shift solenoid valve SLT Transmission valve body assembly Torque converter assembly Automatic transmission assembly	Comes on	DTC stored	SAE Code: P2808

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

MIL

Memory

Note

P2807-7F

Pressure Control Solenoid "G" Actuator Stuck Off

All of the following conditions are met (2-trip detection logic):

Engine coolant temperature is 40°C (104°F) or higher.
ATF temperature is -10°C (14°F) or higher.
The vehicle is driven with the shift lever in D.
No malfunctions are detected in the shift solenoid valve SL1, SL2, SL3, SL4, SL5 and SR, transmission revolution sensors (NT, NC3 and SP2), oil pressure switch, engine coolant temperature sensor, ATF temperature sensor, knock control sensor, electronic throttle and CAN communication system.
Either of the following conditions is met:
1. Any of the following conditions are met 2 times:
  1. When gear shifts to 1st are requested by the ECM, actual gear changes to 4th gear.
  2. When gear shifts to 2nd are requested by the ECM, actual gear changes to 4th gear.
  3. When gear shifts to 5th are requested by the ECM, actual gear changes to 6th gear.
  4. When gear shifts to 8th are requested by the ECM, actual gear changes to 6th gear.
2. When gear shifts to 4th or 6th are requested by the ECM, the engine speed overruns (neutral status) for 0.5 seconds or more.

DTC Detection Condition 1, 2, 3, 4 and 5 (a):

Shift solenoid valve SL4
Transmission valve body assembly
Torque converter assembly
Automatic transmission assembly

DTC Detection Condition 1, 2, 3, 4 and 5 (b):

Shift solenoid valve SL4
Shift solenoid valve SLT
Transmission valve body assembly
Torque converter assembly
Automatic transmission assembly

Comes on

DTC stored

SAE Code: P2808

DTC DETECTION CONDITION PATTERNS:

		Vehicle Condition
		Pattern 1	Pattern 2	Pattern 3	Pattern 4	Pattern 5	Pattern 6
Diagnostic Condition	Engine coolant temperature is 40°C (104°F) or higher.	◦	◦	◦	◦	◦	◦
	ATF temperature is -10°C (14°F) or more.	◦	◦	◦	◦	◦	◦
	The vehicle is driven with the shift lever in D.	◦	◦	◦	◦	◦	◦
	No malfunctions are detected in the shift solenoid valve SL1, SL2, SL3, SL4, SL5 and SR, transmission revolution sensors (NT, NC3 and SP2), oil pressure switch, engine coolant temperature sensor, ATF temperature sensor, knock control sensor, electronic throttle and CAN communication system.	◦	◦	◦	◦	◦	◦
Malfunction Condition	When gear shifts to 1st are requested by the ECM, actual gear changes to 4th gear.	◦	-	-	-	-	-
	When gear shifts to 2nd are requested by the ECM, actual gear changes to 4th gear.	-	◦	-	-	-	-
	When gear shifts to 5th are requested by the ECM, actual gear changes to 6th gear.	-	-	◦	-	-	-
	When gear shifts to 8th are requested by the ECM, actual gear changes to 6th gear.	-	-	-	◦	-	-
	When gear shifts to 4th are requested by the ECM, the engine speed overruns (neutral status).	-	-	-	-	◦	-
	When gear shifts to 6th are requested by the ECM, the engine speed overruns (neutral status).	-	-	-	-	-	◦
Duration		2 times	2 times	2 times	2 times	0.5 seconds or more	0.5 seconds or more
Detection Logic		2-trip detection logic	2-trip detection logic	2-trip detection logic	2-trip detection logic	2-trip detection logic	2-trip detection logic

HINT:

This DTC is stored when any of the above detection patterns are met.