DTC P2713-7F: Pressure Control Solenoid "D" Actuator Stuck Off [10/2017 - 09/2019]: Procedure

1. Connect the Techstream to the DLC3.
2. Turn the engine switch on (IG).
3. Turn the Techstream on.
4. Enter the following menus: Powertrain / Transmission / Trouble Codes.

   Powertrain > Transmission > Trouble Codes 

5. Read the DTCs using the Techstream.

   Result

   Result	Proceed to
   Only DTC P2713-7F is output	A
   P2713-7F and one or more of the following DTCs are output: P0745-7F, P0770-7F, P0775-7F, P0795-7F, P2807-7F, P2816-7F	B
   P0745-7F, P0770-7F, P0775-7F, P0795-7F, P2713-7F, P2807-7F or P2816-7F and other DTCs are output	C

   HINT: 

   If any DTCs other than P0745-7F, P0770-7F, P0775-7F, P0795-7F, P2713-7F, P2807-7F and P2816-7F are output, perform troubleshooting for those DTCs first.

Result: 

B 

See step  5

Result: 

C 

GO TO DTC CHART. Refer to  DIAGNOSTIC TROUBLE CODE CHART [10/2017 - 09/2018]  , or refer to  DIAGNOSTIC TROUBLE CODE CHART [09/2018 - 09/2019] 

Result: 

A 

See step  2

1. Remove the shift solenoid valve SLT.

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   *1	Shift Solenoid Valve SLT

   Refer to DISASSEMBLY [04/2013 - ]

2. Measure the resistance according to the value(s) in the table below.

   Standard Resistance

   Tester Connection	Condition	Specified Condition
   Terminal 1 of the shift solenoid valve SLT - terminal 2	20°C (68°F)	5.0 to 5.6 Ω

3. Connect a positive (+) lead from the battery with a 21 W bulb to terminal 1 and a negative (-) lead to terminal 2 of the shift solenoid valve connector. Check that the valve moves and makes an operating sound.

   OK

   Valve moves and makes an operating sound.

   Result

   Proceed to
   OK
   NG

Result: 

NG 

REPLACE SHIFT SOLENOID VALVE SLT. Refer to  COMPONENTS [10/2016 - ] 

Result: 

OK 

See step  3

1. Check the transmission valve body assembly.

   Refer to REMOVAL [10/2016 - ]

   OK

   There is no foreign matter on each valve and they operate smoothly.

   Result

   Proceed to
   OK
   NG

Result: 

NG 

REPAIR OR REPLACE TRANSMISSION VALVE BODY ASSEMBLY. Refer to  COMPONENTS [10/2016 - ] 

Result: 

OK 

See step  4

1. Check the torque converter assembly.

   Refer to INSPECTION [10/2017 - ]

   OK

   The torque converter assembly operates normally.

   Result

   Proceed to
   OK
   NG

Result: 

OK 

REPAIR OR REPLACE AUTOMATIC TRANSMISSION ASSEMBLY. Refer to  COMPONENTS [10/2016 - ] 

Result: 

NG 

REPLACE TORQUE CONVERTER ASSEMBLY. Refer to  COMPONENTS [10/2016 - ] 

1. Connect the Techstream to the DLC3.
2. Turn the engine switch on (IG).
3. Turn the Techstream on.
4. Enter the following menus: Powertrain / Transmission / Trouble Codes.

   Powertrain > Transmission > Trouble Codes 

5. Check if DTCs other than P2713-7F are output.

   Result

   Result	Proceed to
   Only DTCs P2713-7F and P0745-7F are output	A
   Only DTCs P2713-7F, P0770-7F and P0775-7F are output Only DTCs P2713-7F and P0775-7F are output	B
   Only DTCs P2713-7F, P0770-7F and P0795-7F are output Only DTCs P2713-7F and P0795-7F are output Only DTCs P2713-7F, P0795-7F and P2807-7F are output	C
   Only DTCs P2713-7F and P2807-7F are output	D
   Only DTCs P2713-7F and P2816-7F are output	E

Result: 

A 

GO TO DTC P0745-7F FLOWCHART. Refer to  DTC P0745-7F: Pressure Control Solenoid "A" Actuator Stuck Off [10/2017 - 09/2019] 

Result: 

B 

GO TO DTC P0775-7F FLOWCHART. Refer to  DTC P0775-7F: Pressure Control Solenoid "B" Actuator Stuck Off [10/2017 - 09/2019] 

Result: 

C 

GO TO DTC P0795-7F FLOWCHART. Refer to  DTC P0795-7F: Pressure Control Solenoid "C" Actuator Stuck Off [10/2017 - 09/2019]  

Result: 

D 

GO TO DTC P2807-7F FLOWCHART. Refer to  DTC P2807-7F: Pressure Control Solenoid "G" Actuator Stuck Off [10/2017 - 09/2019] 

Result: 

E 

GO TO DTC P2816-7F FLOWCHART. Refer to  DTC P2816-7F: Pressure Control Solenoid "H" Actuator Stuck Off [10/2017 - 09/2019]