LEMON Manuals: Even more car manuals for everyone
Home >> Lexus >> 2017 >> IS 300 F Sport >> Repair and Diagnosis >> Accessories & Equipment >> Headlights >> Lighting System (Ext) - Service Information >> Rear Combination Light Assembly >> Removal [08/2015 - 10/2016] >> Procedure

Removal [08/2015 - 10/2016]: Procedure

  1. REMOVE REAR LIGHT COVER 
    1. Using a screwdriver with its tip wrapped with protective tape, disengage the 6 claws to remove the 2 rear light covers.
      GTY459709Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Protective Tape
  2. REMOVE REAR COMBINATION LIGHT ASSEMBLY 
    1. Apply protective tape around the rear combination light assembly as shown in the illustration.
      GTY464220Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Protective Tape
    2. Remove the 2 screws.
      GTY459208Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Pin
      *b Guide
    3. Push the rear combination light assembly toward the rear of the vehicle to disengage the pin.
      NOTE:

      To prevent the rear combination light assembly from springing out and falling when it is disengaged, place your hand on the rear combination light assembly and press down gently.

      HINT: 

      Pushing on the portion A in the illustration toward the rear of the vehicle will make disengagement of the pin easier.

    4. Disengage the 3 guides to disconnect the rear combination light assembly as shown in the illustration.
    5. Turn the rear combination light socket and wire sub-assembly with the rear turn signal light bulb as shown in the illustration to disconnect them as a unit.
      GTY461357Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    6. Turn the cap as shown in the illustration to disconnect it.
      GTY462013Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Cap
    7. Disconnect the connector to remove the rear combination light assembly.
  3. REMOVE REAR TURN SIGNAL LIGHT BULB 
    1. Remove the rear turn signal light bulb from the rear combination light socket and wire sub-assembly.
  4. REMOVE REAR BUMPER ASSEMBLY 

    Refer to REMOVAL [04/2013 - 10/2016]

  5. REMOVE REAR BUMPER UPPER RETAINER 
    1. Disengage the clamp.
      GTY459375Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Guide
      *b Clamp
    2. Remove the screw.
    3. Disengage the guide to remove the rear bumper upper retainer.
  6. REMOVE LUGGAGE COMPARTMENT FLOOR MAT 

    Refer to PROCEDURE - Step 4

  7. REMOVE SPARE WHEEL COVER TRAY LH 

    Refer to PROCEDURE - Step 5

  8. REMOVE SPARE WHEEL COVER TRAY RH 

    Refer to PROCEDURE - Step 6

  9. REMOVE DECK SIDE TRIM BOX LH 

    Refer to PROCEDURE - Step 7

  10. REMOVE DECK SIDE TRIM BOX RH 

    Refer to PROCEDURE - Step 8

  11. REMOVE REAR LUGGAGE COMPARTMENT TRIM COVER 

    Refer to PROCEDURE - Step 9

  12. REMOVE FRONT LUGGAGE COMPARTMENT TRIM COVER 

    Refer to PROCEDURE - Step 10

  13. REMOVE REAR SEAT ASSEMBLY 

    Refer to REMOVAL [04/2013 - 10/2016]

  14. REMOVE REAR SEAT SUB FLOOR PANEL 

    Refer to PROCEDURE - Step 10

  15. REMOVE NO. 2 ROOM PARTITION COVER 

    Refer to PROCEDURE - Step 11

  16. REMOVE NO. 1 LUGGAGE COMPARTMENT LIGHT ASSEMBLY 

    Refer to PROCEDURE - Step 1

  17. REMOVE FRONT UPPER LUGGAGE COMPARTMENT TRIM COVER 

    Refer to PROCEDURE - Step 16

  18. REMOVE LUGGAGE COMPARTMENT TRIM COVER LH 

    Refer to PROCEDURE - Step 17

  19. REMOVE LUGGAGE COMPARTMENT TRIM COVER RH (for RH Side) 

    Refer to PROCEDURE - Step 18

  20. REMOVE REAR COMBINATION LIGHT SOCKET AND WIRE SUB-ASSEMBLY 
    1. Disconnect the connector.
      GTY461353Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Disengage the grommet to remove the rear combination light socket and wire sub-assembly.
scientia non olet · About LEMON Manuals