LEMON Manuals: Even more car manuals for everyone
Home >> Lexus >> 2017 >> IS 300 Base >> Repair and Diagnosis >> Accessories & Equipment >> Gauges & Instrument Panels >> Meter / Gauge System - Diagnostics - Introduction (2 Of 6) >> Meter / Gauge System >> Customize Parameters [09/2020 - 11/2021] >> Customize Parameters [09/2020 - 11/2021]

Customize Parameters [09/2020 - 11/2021]

  1. CUSTOMIZE METER / GAUGE SYSTEM 
    1. Customizing with the Techstream
      1. Connect the Techstream to the DLC3.
      2. Turn the engine switch on (IG).
      3. Turn the Techstream on.
      4. Enter the following menus: Customize Setting / Warning or Display.
      5. Select the setting by referring to the table below.
        NOTE:

        Be sure to record the current value before customizing.

        Warning 

        Tester Display Description Default Setting ECU
        Flasher Sound Volume Adjustment Function to change the flasher sound volume Medium 10:Large, 00:Medium, 01:Small Combination meter assembly

        Display 

        Tester Display Description Default Setting ECU
        ODO Display Time After IG OFF Setting Function to change the ODO display time after the engine switch is turned off 30s 00:30s, 01:60s, 10:600s, 11:OFF Combination meter assembly
    2. Customizing with the multi-information display
      NOTE:
      • When the cable is disconnected from the negative (-) battery terminal, some of the settings will be reset. Therefore, it is necessary to make a note of each set value before disconnecting the cable.
      • As some values cannot be selected when the vehicle is being driven, perform the procedure with the vehicle stopped.

      HINT: 

      Depending on the specifications of the vehicle, some items may not be displayed.

      1. except F SPORT Models
        1. Select the settings tab on the multi-information display.
        2. Select the setting by referring to the table below.
          1. LTA

            Display Description Setting ECU
            "Lane Center" Lane centering function setting ON/OFF Forward recognition camera
            "Alert" Lane departure alert method setting Steering vibration/buzzer
            "Sensitivity" Lane departure alert timing level setting 2 levels
            "Sway Warning" Vehicle sway warning function setting ON/OFF
            "Sway Sensitivity" Sway warning sensitivity level setting 3 levels
          2. "CURVE SPEED REDUCTION"

            Display Description Setting ECU
            - Curve speed reduction level setting 2 levels/OFF Forward recognition camera
          3. PCS

            Display Description Setting ECU
            - Pre-collision system setting ON/OFF Forward recognition camera
            "Sensitivity" Pre-collision system sensitivity level setting 3 levels
          4. BSM

            Display Description Setting ECU
            - Blind spot monitor system setting ON/OFF Blind spot monitor sensor LH (B)
            "Brightness" Outer rear view mirror indicator brightness level setting 2 levels
            "Sensitivity" Blind spot monitor system sensitivity level setting 4 levels
          5. PKSA

            Display Description Setting ECU
            - Parking support alert system setting ON/OFF Clearance warning ECU assembly
            RCTA  Rear crossing traffic alert function setting ON/OFF Blind spot monitor sensor LH (B)
            Volume Clearance warning buzzer (RCTA buzzer) volume setting 3 levels Clearance warning ECU assembly
          6. RCTA

            Display Description Setting ECU
            RCTA  Rear crossing traffic alert function setting ON/OFF Blind spot monitor sensor LH (B)
            Volume RCTA buzzer volume setting 3 levels
          7. PKSB

            Display Description Setting ECU
            - Parking support brake system setting ON/OFF Clearance warning ECU assembly
          8. RSA

            Display Description Setting ECU
            RSA Road sign assist system setting ON/OFF Forward recognition camera
            "Excess Speed" Excess speed notification method setting "No Notification/Only Visual/Visual & Audible"
            "Notification Level" Excess speed notification level setting -5 to 10
            "No Overtaking" No overtaking notification method setting "No Notification/Only Visual/Visual and Haptic"
            "Other Signs" Others traffic sign notification method setting "No Notification/Only Visual/Visual & Audible"
          9. "CLOCK"

            Display Description Setting ECU
            - 24H/12H setting 24H/12H Combination meter assembly
          10. "VEHICLE SETTINGS"

            Display Description Setting ECU
            "Scheduled Maintenance" Scheduled maintenance required reminder data reset Yes/No Combination meter assembly
            "Oil Maintenance" Engine oil maintenance required reminder data reset Yes/No Combination meter assembly
          11. "METER SETTINGS"

            Display Description Setting ECU
            "Language" Display language setting *1 Related ECUs
            "Units" Display units setting *1
            Eco driving indicator light Eco driving indicator light display setting ON/OFF Combination meter assembly
            "Drive Info 1" Displayed drive information display item setting *2
            "Drive Info 2" Displayed drive information display item setting *2
            "Drive Info 3" Displayed drive information display item setting *2
            "Pop-Up Display" "TbT Navigation" Interrupt display setting for navigation system-linked ON/OFF
            "Telephone" Interrupt display setting for phone-linked ON/OFF
            "Audio Operation" Interrupt display setting for audio system-linked ON/OFF
            "Volume Operation" Interrupt display setting for volume operation ON/OFF
            "Brightness" Interrupt display setting for illumination level ON/OFF
            "Color" Accent color setting 2 colors
            "Tachometer Settings" Displayed tachometer display setting "On (Self-Changing)/Tachometer (Always)"
            "Default Settings" Reset the combination meter settings to the default setting Yes/No Related ECUs
            1. *1: Varies according to the vehicle specification.
            2. *2: Any combination can be selected for the following items.
              Item 1 Item 2
              "Current" "Bar Type"
              "AVG. Fuel Economy" "After Reset"
              "After Start"
              "After Refuel"
              "Average Speed" "After Reset"
              "After Start"
              "Elapsed Time" "After Reset"
              "After Start"
              "Distance" "Range"
              "After Start"
              "Other" "Blank"
      2. for F SPORT Models
        1. Move the movable meter ring to the side.
        2. Select the settings tab on the multi-information display.
        3. Select the setting by referring to the table below.
          1. LTA "LANE CENTER"

            Display Description Setting ECU
            - Lane centering function setting ON/OFF Forward recognition camera
          2. LTA "ALERT"

            Display Description Setting ECU
            - Lane departure alert method setting Steering vibration/buzzer Forward recognition camera
          3. LTA "SENSITIVITY"

            Display Description Setting ECU
            - Lane departure alert timing level setting 2 levels Forward recognition camera
          4. "CURVE SPEED REDUCTION"

            Display Description Setting ECU
            - Curve speed reduction level setting 2 levels/OFF Forward recognition camera
          5. PCS

            Display Description Setting ECU
            - Pre-collision system setting ON/OFF Forward recognition camera
          6. PCS "SENSITIVITY"

            Display Description Setting ECU
            "Sensitivity" Pre-collision system sensitivity level setting 3 levels Forward recognition camera
          7. BSM

            Display Description Setting ECU
            - Blind spot monitor system setting ON/OFF Blind spot monitor sensor LH (B)
          8. PKSA

            Display Description Setting ECU
            PKSA  Parking support alert system setting ON/OFF Clearance warning ECU assembly
            RCTA  Rear crossing traffic alert function setting ON/OFF Blind spot monitor sensor LH (B)
            Volume Clearance warning buzzer (RCTA buzzer) volume setting 3 levels Clearance warning ECU assembly
          9. RCTA

            Display Description Setting ECU
            RCTA  Rear crossing traffic alert function setting ON/OFF Blind spot monitor sensor LH (B)
            Volume RCTA buzzer volume setting 3 levels
          10. PKSB

            Display Description Setting ECU
            - Parking support brake system setting ON/OFF Clearance warning ECU assembly
          11. "VEHICLE SETTINGS"

            Display Description Setting ECU
            LTA "Sway Warning" Vehicle sway warning function setting ON/OFF Forward recognition camera
            "Sway Sensitivity" Sway warning sensitivity level setting 3 levels
            BSM "Brightness" Outer rear view mirror indicator brightness level setting 2 levels Blind spot monitor sensor LH (B)
            "Sensitivity" Blind spot monitor system sensitivity level setting 4 levels
            RSA RSA Road sign assist system setting ON/OFF Forward recognition camera
            "Excess Speed" Excess speed notification method setting "No Notification/Only Visual/Visual & Audible"
            "Notification Level" Excess speed notification level setting -5 to 10
            "No Overtaking" No overtaking notification method setting "No Notification/Only Visual/Visual and Haptic"
            "Other Signs" Others traffic sign notification method setting "No Notification/Only Visual/Visual & Audible"
            "Scheduled Maintenance" Scheduled maintenance required reminder data reset Yes/No Combination meter assembly
            "Oil Maintenance" Engine oil maintenance required reminder data reset Yes/No ECM
          12. "METER SETTINGS"

            Display Description Setting ECU
            "Language" Display language setting *1 Related ECUs
            "Units" Display units setting *1
            "Drive Info 1" Displayed drive information display item setting *2 Combination meter assembly
            "Drive Info 2" Displayed drive information display item setting *2
            "Clock" 24H/12H setting 24H/12H
            "Pop-Up Display" "TbT Navigation" Interrupt display setting for navigation system-linked ON/OFF
            "Telephone" Interrupt display setting for phone-linked ON/OFF
            "Audio Operation" Interrupt display setting for audio system-linked ON/OFF
            "Volume Operation" Interrupt display setting for volume operation ON/OFF
            "Brightness" Interrupt display setting for illumination level ON/OFF
            "Color" Accent color setting 2 colors
            "Tachometer Settings" Displayed tachometer display setting "On (Self-Changing)/Tachometer (Always)"
            "REV Indicator" "REV Indicator" REV indicator display setting ON/OFF
            "Rev Setting" REV indicator displayed engine speed setting 2000 to 6000
            "REV Peak" REV peak hold display setting ON/OFF
            Eco driving indicator light Eco driving indicator light display setting ON/OFF
            "Default Settings" Reset the combination meter settings to the default setting Yes/No Related ECUs
            1. *1: Varies according to the vehicle specification.
            2. *2: Any combination can be selected for the following items.
              Item 1 Item 2
              "Current" "Bar Type"
              "AVG. Fuel Economy" "After Reset"
              "After Start"
              "After Refuel"
              "Average Speed" "After Reset"
              "After Start"
              "Elapsed Time" "After Reset"
              "After Start"
              "Distance" "Range"
              "After Start"
              "Other" "Blank"
scientia non olet · About LEMON Manuals