Problem Symptoms Table [09/2014 - 10/2015]
NOTE:
- Recognition code registration is necessary when replacing the main body ECU (multiplex network body ECU) and certification ECU (smart key ECU assembly).
- Before replacing the certification ECU (smart key ECU assembly), refer to Registration (Refer to REGISTRATION [09/2014 - 10/2015] ).
- If the main body ECU (multiplex network body ECU) is replaced, refer to Registration (Refer to REGISTRATION [09/2014 - 10/2015] ).
HINT:
- Use the table below to help determine the cause of problem symptoms. If multiple suspected areas are listed, the potential causes of the symptoms are listed in order of probability in the "Suspected Area" column of the table. Check each symptom by checking the suspected areas in the order they are listed. Replace parts as necessary.
- Inspect the fuses and relays related to this system before inspecting the suspected areas below.
METER GAUGE
| Symptom | Suspected Area | Reference |
|---|---|---|
| Speedometer malfunction | Speedometer circuit | Refer to Speedometer Malfunction [09/2014 - 10/2015] |
| Tachometer malfunction | Tachometer circuit | Refer to Tachometer Malfunction [09/2014 - 10/2015] |
| Fuel receiver gauge malfunction | Fuel receiver gauge circuit | Refer to Fuel Gauge Malfunction [09/2014 - 10/2015] |
| Engine coolant temperature receiver gauge malfunction | Engine coolant temperature receiver gauge circuit | Refer to Engine Coolant Temperature Gauge Malfunction [09/2014 - 10/2015] |
WARNING LIGHT OR INDICATOR LIGHT
| Symptom | Suspected Area | Reference |
|---|---|---|
| Turn indicator light does not come on (Turn signal light operates normally) | Perform Active Test (Turn Signal [Left] Indicator, Turn Signal [Right] Indicator) | Refer to DATA LIST / ACTIVE TEST [09/2014 - 10/2015] |
| Combination meter assembly | Refer to REMOVAL [09/2014 - ] | |
| Front fog indicator light does not come on (Front fog light operates normally) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2014 - 10/2015] |
| Perform Active Test (Indicat. Lamp Fr FOG) | Refer to DATA LIST / ACTIVE TEST [09/2014 - 10/2015] | |
| Combination meter assembly | Refer to REMOVAL [09/2014 - ] | |
| Main body ECU (Multiplex network body ECU) | Refer to REMOVAL [09/2014 - ] | |
| High beam indicator light does not come on (High beam headlight operates normally) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2014 - 10/2015] |
| Perform Active Test (Indicat. Lamp Beam) | Refer to DATA LIST / ACTIVE TEST [09/2014 - 10/2015] | |
| Combination meter assembly | Refer to REMOVAL [09/2014 - ] | |
| Main body ECU (Multiplex network body ECU) | Refer to REMOVAL [09/2014 - ] | |
| Headlight indicator light does not come on (Headlight operates normally) (for U.S.A.) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2014 - 10/2015] |
| Perform Active Test (Indicat. Lamp Tail) | Refer to DATA LIST / ACTIVE TEST [09/2014 - 10/2015] | |
| Combination meter assembly | Refer to REMOVAL [09/2014 - ] | |
| Main body ECU (Multiplex network body ECU) | Refer to REMOVAL [09/2014 - ] | |
| Taillight indicator light does not come on (Taillight operates normally) (for Canada.) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2014 - 10/2015] |
| Perform Active Test (Indicat. Lamp Tail) | Refer to DATA LIST / ACTIVE TEST [09/2014 - 10/2015] | |
| Combination meter assembly | Refer to REMOVAL [09/2014 - ] | |
| Main body ECU (Multiplex network body ECU) | Refer to REMOVAL [09/2014 - ] | |
| Open door warning light does not come on (Courtesy light switch operates normally) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2014 - 10/2015] |
| Perform Active Test (Indicat. Lamp Doors All Open) | Refer to DATA LIST / ACTIVE TEST [09/2014 - 10/2015] | |
| Combination meter assembly | Refer to REMOVAL [09/2014 - ] | |
| Main body ECU (Multiplex network body ECU) | Refer to REMOVAL [09/2014 - ] | |
| Front seat belt warning light does not come on | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2014 - 10/2015] |
| Perform Active Test (Driver Side Seat Belt) | Refer to DATA LIST / ACTIVE TEST [09/2014 - 10/2015] | |
| Combination meter assembly | Refer to REMOVAL [09/2014 - ] | |
| Main body ECU (Multiplex network body ECU) | Refer to REMOVAL [09/2014 - ] | |
| SRS warning light does not come on | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2014 - 10/2015] |
| Check indicator/warning light | Refer to OPERATION CHECK [09/2014 - 10/2015] | |
| Perform Active Test (Indicat. Lamp Airbag) | Refer to DATA LIST / ACTIVE TEST [09/2014 - 10/2015] | |
| Airbag system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2014 - ] | |
| Master warning light (Others system operates normally) | Check indicator/warning light | Refer to OPERATION CHECK [09/2014 - 10/2015] |
| Perform Active Test (Master Warning) | Refer to DATA LIST / ACTIVE TEST [09/2014 - 10/2015] | |
| Combination meter assembly | Refer to REMOVAL [09/2014 - ] | |
| MIL does not come on | Check indicator/warning light | Refer to OPERATION CHECK [09/2014 - 10/2015] |
| SFI system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2014 - 10/2015] | |
| Combination meter assembly | Refer to REMOVAL [09/2014 - ] | |
| Charge warning light does not come on | Check indicator/warning light | Refer to OPERATION CHECK [09/2014 - 10/2015] |
| Perform Active Test (Indicat. Lamp Charge) | Refer to DATA LIST / ACTIVE TEST [09/2014 - 10/2015] | |
| Harness or connector | - | |
| Generator assembly | Refer to INSPECTION [09/2014 - 10/2015] | |
| Combination meter assembly | Refer to REMOVAL [09/2014 - ] | |
| ECM | Refer to REMOVAL [09/2014 - 10/2015] | |
| EPS warning light does not come on | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2014 - 10/2015] |
| Check indicator/warning light | Refer to OPERATION CHECK [09/2014 - 10/2015] | |
| Perform Active Test (Indicat. EPS) | Refer to DATA LIST / ACTIVE TEST [09/2014 - 10/2015] | |
| Power steering system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2014 - ] | |
| AFS OFF indicator light does not come on | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2014 - 10/2015] |
| Check indicator/warning light | Refer to OPERATION CHECK [09/2014 - 10/2015] | |
| Perform Active Test (Indicat. AFS) | Refer to DATA LIST / ACTIVE TEST [09/2014 - 10/2015] | |
| Combination meter assembly | Refer to REMOVAL [09/2014 - ] | |
| Headlight swivel ECU assembly | Refer to REMOVAL [09/2014 - 10/2015] | |
| Brake warning light does not come on (Brake fluid level normally) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2014 - 10/2015] |
| Check indicator/warning light | Refer to OPERATION CHECK [09/2014 - 10/2015] | |
| Perform Active Test (Indicat. Lamp Brake) | Refer to DATA LIST / ACTIVE TEST [09/2014 - 10/2015] | |
| Vehicle stability control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2014 - 10/2015] | |
| Combination meter assembly | Refer to REMOVAL [09/2014 - ] | |
| Parking brake warning light does not come on | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2014 - 10/2015] |
| Perform Active Test (Indicat. Park) | Refer to DATA LIST / ACTIVE TEST [09/2014 - 10/2015] | |
| Combination meter assembly | Refer to REMOVAL [09/2014 - ] | |
| Parking brake ECU assembly | Refer to REMOVAL [09/2014 - 10/2015] | |
| EPB*/ECB* warning light does not come on | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2014 - 10/2015] |
| Check indicator/warning light | Refer to OPERATION CHECK [09/2014 - 10/2015] | |
| Perform Active Test (Indicat. Lamp ECB*) | Refer to DATA LIST / ACTIVE TEST [09/2014 - 10/2015] | |
| Combination meter assembly | Refer to REMOVAL [09/2014 - ] | |
| Parking brake ECU assembly | Refer to REMOVAL [09/2014 - 10/2015] | |
| Cruise indicator light does not come on | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2014 - 10/2015] |
| Perform Active Test (Indicat. Lamp Cruise) | Refer to DATA LIST / ACTIVE TEST [09/2014 - 10/2015] | |
| Cruise control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2014 - ] | |
| Radar cruise indicator light does not come on (w/ Dynamic Radar Cruise Control System) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2014 - 10/2015] |
| Perform Active Test (Indicat. Radar Cruise) | Refer to DATA LIST / ACTIVE TEST [09/2014 - 10/2015] | |
| Dynamic radar cruise control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2014 - 10/2015] | |
| Combination meter assembly | Refer to REMOVAL [09/2014 - ] | |
| SET indicator light does not come on | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2014 - 10/2015] |
| Perform Active Test (Indicat. SET) | Refer to DATA LIST / ACTIVE TEST [09/2014 - 10/2015] | |
| Cruise control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2014 - ] | |
| Dynamic radar cruise control system (w/ Dynamic Radar Cruise Control System) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2014 - 10/2015] | |
| Combination meter assembly | Refer to REMOVAL [09/2014 - ] | |
| Clearance sonar indicator light does not come on (w/ Intuitive Parking Assist System) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2014 - 10/2015] |
| Perform Active Test (Indicat. Clearance Sonar LCD) | Refer to DATA LIST / ACTIVE TEST [09/2014 - 10/2015] | |
| Combination meter assembly | Refer to REMOVAL [09/2014 - ] | |
| Clearance warning ECU assembly | Refer to REMOVAL [09/2014 - ] | |
| Fuel level warning light does not come on (Fuel receiver gauge operates normally) | Perform Active Test (Indicat. Lamp Fuel) | Refer to DATA LIST / ACTIVE TEST [09/2014 - 10/2015] |
| Combination meter assembly | Refer to REMOVAL [09/2014 - ] | |
| ABS warning light does not come on | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2014 - 10/2015] |
| Check indicator/warning light | Refer to OPERATION CHECK [09/2014 - 10/2015] | |
| Perform Active Test (Indicat. Lamp ABS) | Refer to DATA LIST / ACTIVE TEST [09/2014 - 10/2015] | |
| Vehicle stability control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2014 - 10/2015] | |
| Combination meter assembly | Refer to REMOVAL [09/2014 - ] | |
| Slip indicator light does not come on | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2014 - 10/2015] |
| Check indicator/warning light | Refer to OPERATION CHECK [09/2014 - 10/2015] | |
| Perform Active Test (Indicat. Lamp Slip) | Refer to DATA LIST / ACTIVE TEST [09/2014 - 10/2015] | |
| Vehicle stability control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2014 - 10/2015] | |
| Combination meter assembly | Refer to REMOVAL [09/2014 - ] | |
| VSC OFF indicator light does not come on | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2014 - 10/2015] |
| Check indicator/warning light | Refer to OPERATION CHECK [09/2014 - 10/2015] | |
| Perform Active Test (Indicat. VSC OFF) | Refer to DATA LIST / ACTIVE TEST [09/2014 - 10/2015] | |
| Vehicle stability control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2014 - 10/2015] | |
| Combination meter assembly | Refer to REMOVAL [09/2014 - ] | |
| PCS warning light does not come on (w/ Pre-collision System) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2014 - 10/2015] |
| Check indicator/warning light | Refer to OPERATION CHECK [09/2014 - 10/2015] | |
| Perform Active Test (Indicat. Precrash) | Refer to DATA LIST / ACTIVE TEST [09/2014 - 10/2015] | |
| Combination meter assembly | Refer to REMOVAL [09/2014 - ] | |
| Seat belt control ECU | Refer to REMOVAL [09/2014 - 10/2015] | |
| Brake actuator assembly (Skid control ECU) | Refer to REMOVAL [09/2014 - 10/2015] | |
| LKA indicator light does not come on (w/ Lane-keeping Assist System) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2014 - 10/2015] |
| Perform Active Test (Drift From The Lane) | Refer to DATA LIST / ACTIVE TEST [09/2014 - 10/2015] | |
| Combination meter assembly | Refer to REMOVAL [09/2014 - ] | |
| Driving support ECU assembly | Refer to REMOVAL [09/2014 - 10/2015] | |
| Tire pressure warning light does not come on | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2014 - 10/2015] |
| Check indicator/warning light | Refer to OPERATION CHECK [09/2014 - 10/2015] | |
| Perform Active Test (Indicat. Tire Pressure Warning System) | Refer to DATA LIST / ACTIVE TEST [09/2014 - 10/2015] | |
| Combination meter assembly | Refer to REMOVAL [09/2014 - ] | |
| Main body ECU (Multiplex network body ECU) | Refer to REMOVAL [09/2014 - ] |
- EPB*: Electro-mechanical Parking Brake
- ECB*: Electronically Controlled Brake System
MULTI-INFORMATION DISPLAY
| Symptom | Suspected Area | Reference |
|---|---|---|
| Outside temperature display malfunction | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2014 - 10/2015] |
| Air conditioning system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2014 - ] | |
| Air conditioning amplifier assembly | Refer to REMOVAL [09/2014 - ] | |
| Current fuel consumption display malfunction (Combination meter assembly operates normally) | Combination meter assembly | Refer to REMOVAL [09/2014 - ] |
| Average fuel consumption after refueling display malfunction (Combination meter assembly operates normally) | Combination meter assembly | Refer to REMOVAL [09/2014 - ] |
| Average fuel consumption display malfunction (Combination meter assembly operates normally) | Combination meter assembly | Refer to REMOVAL [09/2014 - ] |
| Average vehicle speed display malfunction (Combination meter assembly operates normally) | Combination meter assembly | Refer to REMOVAL [09/2014 - ] |
| Driving range display malfunction (Combination meter assembly operates normally) | Combination meter assembly | Refer to REMOVAL [09/2014 - ] |
| Tire pressure display malfunction | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2014 - 10/2015] |
| Tire pressure warning system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2014 - ] | |
| Main body ECU (Multiplex network body ECU) | Refer to REMOVAL [09/2014 - ] | |
| Eco driving indicator zone display malfunction | Check customize setting | Refer to CUSTOMIZE PARAMETERS [09/2014 - 10/2015] |
| CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2014 - 10/2015] | |
| SFI system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2014 - 10/2015] | |
| Combination meter assembly | Refer to REMOVAL [09/2014 - ] | |
| ECM | Refer to REMOVAL [09/2014 - 10/2015] | |
| Rheostat display malfunction | Read The Data List (Light Control Up Switch, Light Control Down Switch) | Refer to DATA LIST / ACTIVE TEST [09/2014 - 10/2015] |
| Trip switch | Refer to INSPECTION [09/2014 - ] | |
| Harness or connector | - | |
| Combination meter assembly | Refer to REMOVAL [09/2014 - ] | |
| ODO/TRIP meter display malfunction (Combination meter assembly operates normally) | Combination meter assembly | Refer to REMOVAL [09/2014 - ] |
| DTCs display malfunction (Others system operates normally) | Combination meter assembly | Refer to REMOVAL [09/2014 - ] |
| "AWD Test Mode" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (for AWD) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2014 - 10/2015] |
| Combination meter assembly | Refer to REMOVAL [09/2014 - ] | |
| 4WD ECU assembly | Refer to REMOVAL [09/2014 - ] | |
| "VGRS Test Mode" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Variable Gear Ratio Steering System) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2014 - 10/2015] |
| Combination meter assembly | Refer to REMOVAL [09/2014 - ] | |
| Front steering control ECU | Refer to REMOVAL [09/2014 - ] | |
| "DRS Test Mode" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Variable Gear Ratio Steering System) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2014 - 10/2015] |
| Combination meter assembly | Refer to REMOVAL [09/2014 - ] | |
| Rear steering control ECU | Refer to REMOVAL [09/2014 - ] | |
| "Adjusting LKA Camera" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Lane-keeping Assist System) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2014 - 10/2015] |
| Lane-keeping assist system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2014 - 10/2015] | |
| Combination meter assembly | Refer to REMOVAL [09/2014 - ] | |
| Driving support ECU assembly | Refer to REMOVAL [09/2014 - 10/2015] | |
| "Adjusting Front Radar Beam" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Dynamic Radar Cruise Control System) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2014 - 10/2015] |
| Dynamic radar cruise control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2014 - 10/2015] | |
| Combination meter assembly | Refer to REMOVAL [09/2014 - ] | |
| Driving support ECU assembly | Refer to REMOVAL [09/2014 - 10/2015] | |
| "Checking Cruise Control C/D" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2014 - 10/2015] |
| Cruise control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2014 - ] | |
| Dynamic radar cruise control system (w/ Dynamic Radar Cruise Control System) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2014 - 10/2015] | |
| Combination meter assembly | Refer to REMOVAL [09/2014 - ] | |
| ECM | Refer to REMOVAL [09/2014 - 10/2015] | |
| "Checking Cruise Control Brake" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2014 - 10/2015] |
| Cruise control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2014 - ] | |
| Dynamic radar cruise control system (w/ Dynamic Radar Cruise Control System) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2014 - 10/2015] | |
| Combination meter assembly | Refer to REMOVAL [09/2014 - ] | |
| ECM | Refer to REMOVAL [09/2014 - 10/2015] | |
| "BRAKE!" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Pre-collision System) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2014 - 10/2015] |
| Pre-collision system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2014 - 10/2015] | |
| Combination meter assembly | Refer to REMOVAL [09/2014 - ] | |
| Driving support ECU assembly | Refer to REMOVAL [09/2014 - 10/2015] | |
| "Brake Malfunction" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (Vehicle stability control system operates normally) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2014 - 10/2015] |
| Combination meter assembly | Refer to REMOVAL [09/2014 - ] | |
| Brake actuator assembly (Skid control ECU) | Refer to REMOVAL [09/2014 - 10/2015] | |
| Open door message display malfunction | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2014 - 10/2015] |
| Combination meter assembly | Refer to REMOVAL [09/2014 - ] | |
| Main body ECU (Multiplex network body ECU) | Refer to REMOVAL [09/2014 - ] | |
| Clearance warning display malfunction (w/ Intuitive Parking Assist System) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2014 - 10/2015] |
| Intuitive parking assist system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2014 - ] | |
| Clearance warning ECU assembly | Refer to REMOVAL [09/2014 - ] | |
| "Check Park Sonar System" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Intuitive Parking Assist System) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2014 - 10/2015] |
| Intuitive parking assist system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2014 - ] | |
| Clearance warning ECU assembly | Refer to REMOVAL [09/2014 - ] | |
| "Clean Park Sonar" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Intuitive Parking Assist System) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2014 - 10/2015] |
| Intuitive parking assist system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2014 - ] | |
| Clearance warning ECU assembly | Refer to REMOVAL [09/2014 - ] | |
| "Auto Power OFF to Conserve Battery" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2014 - 10/2015] |
| Combination meter assembly | Refer to REMOVAL [09/2014 - ] | |
| Certification ECU (Smart key ECU assembly) | Refer to REMOVAL [09/2014 - ] | |
| "Shift to P position" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2014 - 10/2015] |
| Smart access system with push-button start (for Start Function) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2014 - ] | |
| Certification ECU (Smart key ECU assembly) | Refer to REMOVAL [09/2014 - ] | |
| "Check Power Steering System" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2014 - 10/2015] |
| Power steering system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2014 - ] | |
| Power steering ECU assembly | Refer to REMOVAL [09/2014 - ] | |
| "Release Parking Brake" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (Brake warning light operates normally) | Combination meter assembly | Refer to REMOVAL [09/2014 - ] |
| "To park the vehicle, shift to P position" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2014 - 10/2015] |
| Smart access system with push-button start (for Start Function) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2014 - ] | |
| Certification ECU (Smart key ECU assembly) | Refer to REMOVAL [09/2014 - ] | |
| "Key not detected" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2014 - 10/2015] |
| Smart access system with push-button start (for Start Function) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2014 - ] | |
| Certification ECU (Smart key ECU assembly) | Refer to REMOVAL [09/2014 - ] | |
| "LKA canceled Keep hands on steering wheel" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Lane-keeping Assist System) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2014 - 10/2015] |
| Lane-keeping assist system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2014 - 10/2015] | |
| Combination meter assembly | Refer to REMOVAL [09/2014 - ] | |
| Driving support ECU assembly | Refer to REMOVAL [09/2014 - 10/2015] | |
| "Parking Brake Overheat" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2014 - 10/2015] |
| Electric parking brake system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2014 - ] | |
| Parking brake ECU assembly | Refer to REMOVAL [09/2014 - 10/2015] | |
| "Check SRS Airbag System" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2014 - 10/2015] |
| Airbag system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2014 - ] | |
| Center airbag sensor assembly | Refer to REMOVAL [09/2014 - ] | |
| "Check ABS" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2014 - 10/2015] |
| Vehicle stability control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2014 - 10/2015] | |
| Combination meter assembly | Refer to REMOVAL [09/2014 - ] | |
| Brake actuator assembly (Skid control ECU) | Refer to REMOVAL [09/2014 - 10/2015] | |
| "Engine Overheat" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2014 - 10/2015] |
| SFI system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2014 - 10/2015] | |
| Combination meter assembly | Refer to REMOVAL [09/2014 - ] | |
| ECM | Refer to REMOVAL [09/2014 - 10/2015] | |
| "Clean Radar Sensor" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Dynamic Radar Cruise Control System) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2014 - 10/2015] |
| Dynamic radar cruise control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2014 - 10/2015] | |
| Combination meter assembly | Refer to REMOVAL [09/2014 - ] | |
| ECM | Refer to REMOVAL [09/2014 - 10/2015] | |
| "Cruise control not available" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Dynamic Radar Cruise Control System) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2014 - 10/2015] |
| Dynamic radar cruise control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2014 - 10/2015] | |
| Combination meter assembly | Refer to REMOVAL [09/2014 - ] | |
| ECM | Refer to REMOVAL [09/2014 - 10/2015] | |
| "LKA not available" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Lane-keeping Assist System) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2014 - 10/2015] |
| Lane-keeping assist system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2014 - 10/2015] | |
| Combination meter assembly | Refer to REMOVAL [09/2014 - ] | |
| Driving support ECU assembly | Refer to REMOVAL [09/2014 - 10/2015] | |
| "1st Gear not available due to slippery road surface" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2014 - 10/2015] |
| Automatic transmission system (A760H) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2014 - 10/2015] | |
| Automatic transmission system (AA81E) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2014 - 10/2015] | |
| Combination meter assembly | Refer to REMOVAL [09/2014 - ] | |
| ECM | Refer to REMOVAL [09/2014 - 10/2015] | |
| "Check Access System with Elec. Key" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2014 - 10/2015] |
| Smart access system with push-button start (for Entry Function) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2014 - ] | |
| Smart access system with push-button start (for Start Function) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2014 - ] | |
| Certification ECU (Smart key ECU assembly) | Refer to REMOVAL [09/2014 - ] | |
| "BSM not available" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Blind Spot Monitor System) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2014 - 10/2015] |
| Blind spot monitor system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2014 - ] | |
| Blind spot monitor sensor | Refer to REMOVAL [09/2014 - ] | |
| "Check cruise control system" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2014 - 10/2015] |
| Cruise control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2014 - ] | |
| Dynamic radar cruise control system (w/ Dynamic Radar Cruise Control System) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2014 - 10/2015] | |
| Combination meter assembly | Refer to REMOVAL [09/2014 - ] | |
| ECM | Refer to REMOVAL [09/2014 - 10/2015] | |
| "Check LKA system" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Lane-keeping Assist System) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2014 - 10/2015] |
| Lane-keeping assist system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2014 - 10/2015] | |
| Combination meter assembly | Refer to REMOVAL [09/2014 - ] | |
| Driving support ECU assembly | Refer to REMOVAL [09/2014 - 10/2015] | |
| "Check PCS system" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Pre-collision System) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2014 - 10/2015] |
| Pre-collision system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2014 - 10/2015] | |
| Combination meter assembly | Refer to REMOVAL [09/2014 - ] | |
| Seat belt control ECU | Refer to REMOVAL [09/2014 - 10/2015] | |
| "Check BSM System" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Blind Spot Monitor System) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2014 - 10/2015] |
| Blind spot monitor system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2014 - ] | |
| Blind spot monitor sensor | Refer to REMOVAL [09/2014 - ] | |
| "Engine Oil pressure Low" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | Engine oil pressure switch assembly | Refer to INSPECTION [09/2014 - 10/2015] |
| Harness or connector | - | |
| Combination meter assembly | Refer to REMOVAL [09/2014 - ] | |
| "Transmission Fluid High temperature" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2014 - 10/2015] |
| Automatic transmission system (A760H) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2014 - 10/2015] | |
| Automatic transmission system (AA81E) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2014 - 10/2015] | |
| Combination meter assembly | Refer to REMOVAL [09/2014 - ] | |
| ECM | Refer to REMOVAL [09/2014 - 10/2015] | |
| "Check AWD System" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (for AWD) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2014 - 10/2015] |
| Four wheel drive control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2014 - ] | |
| 4WD ECU assembly | Refer to REMOVAL [09/2014 - ] | |
| "Check VGRS System" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Variable Gear Ratio Steering System) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2014 - 10/2015] |
| Variable gear ratio steering system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2014 - ] | |
| Front steering control ECU | Refer to REMOVAL [09/2014 - ] | |
| "Check DRS System" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Variable Gear Ratio Steering System) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2014 - 10/2015] |
| Dynamic rear steering system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2014 - ] | |
| Rear steering control ECU | Refer to REMOVAL [09/2014 - ] | |
| "Parking Brake Inoperable" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2014 - 10/2015] |
| Electric parking brake system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2014 - ] | |
| Parking brake ECU assembly | Refer to REMOVAL [09/2014 - 10/2015] | |
| "Check Parking Brake System" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2014 - 10/2015] |
| Electric parking brake system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2014 - ] | |
| Parking brake ECU assembly | Refer to REMOVAL [09/2014 - 10/2015] | |
| "Turn power OFF" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2014 - 10/2015] |
| Smart access system with push-button start (for Entry Function) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2014 - ] | |
| Certification ECU (Smart key ECU assembly) | Refer to REMOVAL [09/2014 - ] | |
| "Key detected in vehicle" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2014 - 10/2015] |
| Smart access system with push-button start (for Entry Function) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2014 - ] | |
| Certification ECU (Smart key ECU assembly) | Refer to REMOVAL [09/2014 - ] | |
| "Turn Light Off" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2014 - 10/2015] |
| Lighting system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2014 - 10/2015] | |
| Combination meter assembly | Refer to REMOVAL [09/2014 - ] | |
| Main body ECU (Multiplex network body ECU) | Refer to REMOVAL [09/2014 - ] | |
| "Moon Roof opened" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Sliding Roof) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2014 - 10/2015] |
| Siding roof system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2014 - ] | |
| Main body ECU (Multiplex network body ECU) | Refer to REMOVAL [09/2014 - ] | |
| "Window opened" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2014 - 10/2015] |
| Power window control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2014 - ] | |
| Main body ECU (Multiplex network body ECU) | Refer to REMOVAL [09/2014 - ] | |
| "Window/Moon Roof opened" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Sliding Roof) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2014 - 10/2015] |
| Power window control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2014 - ] | |
| Siding roof system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2014 - ] | |
| Main body ECU (Multiplex network body ECU) | Refer to REMOVAL [09/2014 - ] | |
| "Depress brake pedal, touch engine switch with key" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2014 - 10/2015] |
| Smart access system with push-button start (for Start Function) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2014 - ] | |
| Certification ECU (Smart key ECU assembly) | Refer to REMOVAL [09/2014 - ] | |
| "Depress brake pedal and push engine switch to start" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2014 - 10/2015] |
| Smart access system with push-button start (for Start Function) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2014 - ] | |
| Certification ECU (Smart key ECU assembly) | Refer to REMOVAL [09/2014 - ] | |
| "Shift to P to start" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2014 - 10/2015] |
| Smart access system with push-button start (for Start Function) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2014 - ] | |
| Certification ECU (Smart key ECU assembly) | Refer to REMOVAL [09/2014 - ] | |
| "Steering Lock active" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2014 - 10/2015] |
| Steering lock system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2014 - ] | |
| Certification ECU (Smart key ECU assembly) | Refer to REMOVAL [09/2014 - ] | |
| "The Parking Brake has been automatically locked" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2014 - 10/2015] |
| Electric parking brake system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2014 - ] | |
| Parking brake ECU assembly | Refer to REMOVAL [09/2014 - 10/2015] | |
| "Key Battery Low" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2014 - 10/2015] |
| Smart access system with push-button start (for Entry Function) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2014 - ] | |
| Certification ECU (Smart key ECU assembly) | Refer to REMOVAL [09/2014 - ] | |
| "Check Headlight Leveling System" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2014 - 10/2015] |
| Lighting system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2014 - 10/2015] | |
| Combination meter assembly | Refer to REMOVAL [09/2014 - ] | |
| Headlight swivel ECU assembly | Refer to REMOVAL [09/2014 - 10/2015] | |
| "Check AFS" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2014 - 10/2015] |
| Lighting system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2014 - 10/2015] | |
| Combination meter assembly | Refer to REMOVAL [09/2014 - ] | |
| Headlight swivel ECU assembly | Refer to REMOVAL [09/2014 - 10/2015] | |
| "Engine Oil Level Low" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | Engine oil level sensor | Refer to INSPECTION [09/2014 - 10/2015] |
| Harness or connector | - | |
| Combination meter assembly | Refer to REMOVAL [09/2014 - ] | |
| "Washer Fluid Low" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | Level warning switch assembly | Refer to INSPECTION [09/2014 - ] |
| Harness or connector | - | |
| Combination meter assembly | Refer to REMOVAL [09/2014 - ] | |
| "Fuel Low" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (Fuel receiver gauge operates normally) | Combination meter assembly | Refer to REMOVAL [09/2014 - ] |
| "TRAC OFF" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2014 - 10/2015] |
| Vehicle stability control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2014 - 10/2015] | |
| Combination meter assembly | Refer to REMOVAL [09/2014 - ] | |
| Brake actuator assembly (Skid control ECU) | Refer to REMOVAL [09/2014 - 10/2015] | |
| "Maintenance required soon" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2014 - 10/2015] |
| SFI system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2014 - 10/2015] | |
| Combination meter assembly | Refer to REMOVAL [09/2014 - ] | |
| ECM | Refer to REMOVAL [09/2014 - 10/2015] | |
| "Maintenance required" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2014 - 10/2015] |
| SFI system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2014 - 10/2015] | |
| Combination meter assembly | Refer to REMOVAL [09/2014 - ] | |
| ECM | Refer to REMOVAL [09/2014 - 10/2015] | |
| "Resetting Maintenance Data" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2014 - 10/2015] |
| SFI system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2014 - 10/2015] | |
| Combination meter assembly | Refer to REMOVAL [09/2014 - ] | |
| ECM | Refer to REMOVAL [09/2014 - 10/2015] | |
| "Resetting of Maintenance Data incomplete" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2014 - 10/2015] |
| SFI system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2014 - 10/2015] | |
| Combination meter assembly | Refer to REMOVAL [09/2014 - ] | |
| ECM | Refer to REMOVAL [09/2014 - 10/2015] | |
| "POWER ON" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2014 - 10/2015] |
| Smart access system with push-button start (for Start Function) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2014 - ] | |
| Certification ECU (Smart key ECU assembly) | Refer to REMOVAL [09/2014 - ] | |
| "PCS temporarily not available" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Pre-collision System) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2014 - 10/2015] |
| Pre-collision system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2014 - 10/2015] | |
| Combination meter assembly | Refer to REMOVAL [09/2014 - ] | |
| Seat belt control ECU | Refer to REMOVAL [09/2014 - 10/2015] | |
| "Operation of Electrical Item Restricted." message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2014 - 10/2015] |
| Air conditioning system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2014 - ] | |
| Air conditioning amplifier assembly | Refer to REMOVAL [09/2014 - ] | |
| "Theft Sensor OFF" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2014 - 10/2015] |
| Theft deterrent system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2014 - 10/2015] | |
| Combination meter assembly | Refer to REMOVAL [09/2014 - ] | |
| Main body ECU (Multiplex network body ECU) | Refer to REMOVAL [09/2014 - ] | |
| "Theft Sensor ON" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2014 - 10/2015] |
| Theft deterrent system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2014 - 10/2015] | |
| Combination meter assembly | Refer to REMOVAL [09/2014 - ] | |
| Main body ECU (Multiplex network body ECU) | Refer to REMOVAL [09/2014 - ] | |
| Multi-information display is missing dots | Perform Active Test (Meter Display 1) | Refer to DATA LIST / ACTIVE TEST [09/2014 - 10/2015] |
| Combination meter assembly | Refer to REMOVAL [09/2014 - ] | |
| The settings cannot be customized through the multi-information display (Language) | Combination meter assembly | Refer to REMOVAL [09/2014 - ] |
| The settings cannot be customized through the multi-information display (Units) | Combination meter assembly | Refer to REMOVAL [09/2014 - ] |
| The settings cannot be customized through the multi-information display (ECO Indicator) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2014 - 10/2015] |
| Combination meter assembly | Refer to REMOVAL [09/2014 - ] | |
| ECM | Refer to REMOVAL [09/2014 - 10/2015] | |
| The settings cannot be customized through the multi-information display (Drive monitor) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2014 - 10/2015] |
| Combination meter assembly | Refer to REMOVAL [09/2014 - ] | |
| Air conditioning amplifier assembly | Refer to REMOVAL [09/2014 - ] | |
| ECM | Refer to REMOVAL [09/2014 - 10/2015] | |
| The settings cannot be customized through the multi-information display (DEFAULT SETTINGS) | Combination meter assembly | Refer to REMOVAL [09/2014 - ] |
BUZZER
| Symptom | Suspected Area | Reference |
|---|---|---|
| No buzzers operate | Combination meter assembly | Refer to REMOVAL [09/2014 - ] |
| Smart key warning buzzer does not operate (Smart access system operates normally) | Combination meter assembly | Refer to REMOVAL [09/2014 - ] |
| Engine immobiliser certification buzzer does not operate (Engine immobiliser system operates normally) | Combination meter assembly | Refer to REMOVAL [09/2014 - ] |
| Dynamic radar cruise control low speed cancel buzzer does not operate (Dynamic radar cruise control system operates normally) (w/ Dynamic Radar Cruise Control System) | Combination meter assembly | Refer to REMOVAL [09/2014 - ] |
| Seat belt warning buzzer does not operate (Front seat belt warning light operates normally) | Combination meter assembly | Refer to REMOVAL [09/2014 - ] |
| VSC buzzer does not operate | Vehicle stability control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2014 - 10/2015] |
| Combination meter assembly | Refer to REMOVAL [09/2014 - ] | |
| PKB-ON driving warning buzzer does not operate (Brake warning light operates normally) | Combination meter assembly | Refer to REMOVAL [09/2014 - ] |
| Driving with any door opened warning buzzer does not operate (Open door warning light and speedometer operate normally) | Combination meter assembly | Refer to REMOVAL [09/2014 - ] |
| Sports shift reject buzzer does not operate (Others system operates normally) | Combination meter assembly | Refer to REMOVAL [09/2014 - ] |
| EPS buzzer does not operate (Power steering system operates normally) | Combination meter assembly | Refer to REMOVAL [09/2014 - ] |
| LKA buzzer does not operate (Lane-keeping assist system operates normally) (w/ Lane-keeping Assist System) | Combination meter assembly | Refer to REMOVAL [09/2014 - ] |
OTHERS
| Symptom | Suspected Area | Reference |
|---|---|---|
| Eco light malfunction | Check customize setting | Refer to CUSTOMIZE PARAMETERS [09/2014 - 10/2015] |
| CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2014 - 10/2015] | |
| Combination meter assembly | Refer to REMOVAL [09/2014 - ] | |
| ECM | Refer to REMOVAL [09/2014 - 10/2015] | |
| Operating light control rheostat does not change light brightness | Light control rheostat circuit | Refer to Operating Light Control Rheostat does not Change Light Brightness [09/2014 - 10/2015] |
| Meter illumination is always dark | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2014 - 10/2015] |
| Lighting system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2014 - 10/2015] | |
| Combination meter assembly | Refer to REMOVAL [09/2014 - ] | |
| Main body ECU (Multiplex network body ECU) | Refer to REMOVAL [09/2014 - ] | |
| ODO/TRIP switch malfunction | ODO/TRIP switch circuit | Refer to Odo/Trip Switch Malfunction [09/2014 - 10/2015] |
| Multi-information display does not change using DISP switch | Read The Data List (Multi Display Select Switch) | Refer to DATA LIST / ACTIVE TEST [09/2014 - 10/2015] |
| Steering pad switch assembly | Refer to INSPECTION [09/2014 - 10/2015] | |
| Spiral with sensor cable sub-assembly | Refer to INSPECTION [09/2014 - 09/2016] | |
| Harness or connector | - | |
| Combination meter assembly | Refer to REMOVAL [09/2014 - ] | |
| Shift position indicator malfunction | Perform Active Test (A/T Indicator Operation 1, A/T Indicator Operation 2, A/T Indicator Operation 3) | Refer to DATA LIST / ACTIVE TEST [09/2014 - 10/2015] |
| CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2014 - 10/2015] | |
| Automatic transmission system (A760H) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2014 - 10/2015] | |
| Automatic transmission system (AA81E) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2014 - 10/2015] | |
| Combination meter assembly | Refer to REMOVAL [09/2014 - ] | |
| ECM | Refer to REMOVAL [09/2014 - 10/2015] | |
| Headup display malfunction (w/ Headup Display) | Headup display circuit | Refer to Headup Display Malfunction [09/2014 - 10/2015] |