LEMON Manuals: Even more car manuals for everyone
Home >> Lexus >> 2016 >> GX 460 Base >> Repair and Diagnosis >> Transmission >> Transfer Case >> Transfer Case (Service Information) >> 4WD Control Ecu >> Removal [08/2015 - ] >> Procedure

Removal [08/2015 - ]: Procedure

  1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL 
    WARNING:

    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    NOTE:
    • w/ Navigation System for HDD:

      After the engine switch is turned off, the display and navigation module display (HDD navigation system) records various types of memory and settings. As a result, after turning the engine switch off, be sure to wait for the time specified in the following table before disconnecting the cable from the negative (-) battery terminal.

      Waiting Time before Disconnecting Cable from Negative (-) Battery Terminal

      Condition Waiting Time
      Vehicle enrolled in safety connect system 6 minutes
      Vehicle not enrolled in safety connect system 1 minute
    • When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Refer to INITIALIZATION [08/2015 - 08/2019] , or refer to INITIALIZATION [08/2019 - 08/2021] , or refer to INITIALIZATION [08/2021 - 08/2022] , or refer to INITIALIZATION [08/2022 - ] ).
  2. REMOVE DOOR SCUFF PLATE ASSEMBLY RH 

    Refer to PROCEDURE - Step 7 [08/2015 - 08/2019] , or refer to PROCEDURE - Step 7 [08/2019 - 08/2021] , or refer to PROCEDURE - Step 7 [08/2021 - ]

  3. REMOVE COWL SIDE TRIM BOARD RH 

    Refer to PROCEDURE - Step 9 [08/2015 - 08/2019] , or refer to PROCEDURE - Step 9 [08/2019 - 08/2021] , or refer to PROCEDURE - Step 9 [08/2021 - ]

  4. REMOVE INSTRUMENT SIDE PANEL RH 

    Refer to PROCEDURE - Step 26 [08/2015 - 08/2019] , or refer to PROCEDURE - Step 26 [08/2019 - 08/2021] , or refer to PROCEDURE - Step 26 [08/2021 - ]

  5. REMOVE CENTER INSTRUMENT CLUSTER FINISH PANEL GARNISH 

    Refer to PROCEDURE - Step 27 [08/2015 - 08/2019] , or refer to PROCEDURE - Step 27 [08/2019 - 08/2021] , or refer to PROCEDURE - Step 27 [08/2021 - ]

  6. REMOVE NO. 2 INSTRUMENT PANEL REGISTER ASSEMBLY 

    Refer to PROCEDURE - Step 28 [08/2015 - 08/2019] , or refer to PROCEDURE - Step 28 [08/2019 - 08/2021] , or refer to PROCEDURE - Step 28 [08/2021 - ]

  7. REMOVE LOWER INSTRUMENT COVER LH 

    Refer to PROCEDURE - Step 29 [08/2015 - 08/2019] , or refer to PROCEDURE - Step 29 [08/2019 - 08/2021] , or refer to PROCEDURE - Step 29 [08/2021 - ]

  8. REMOVE LOWER NO. 2 INSTRUMENT PANEL AIRBAG ASSEMBLY 

    Refer to PROCEDURE - Step 7

  9. REMOVE INSTRUMENT PANEL BOX DOOR COVER 

    Refer to PROCEDURE - Step 31 [08/2015 - 08/2019] , or refer to PROCEDURE - Step 31 [08/2019 - 08/2021] , or refer to PROCEDURE - Step 31 [08/2021 - ]

  10. REMOVE INSTRUMENT PANEL BOX ASSEMBLY 

    Refer to PROCEDURE - Step 32 [08/2015 - 08/2019] , or refer to PROCEDURE - Step 32 [08/2019 - 08/2021] , or refer to PROCEDURE - Step 32 [08/2021 - ]

  11. REMOVE 4 WHEEL DRIVE CONTROL ECU NO. 2 
    GTY257215Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Disconnect the 2 connectors.
    2. Remove the bolt and four wheel drive control ECU.
scientia non olet · About LEMON Manuals