Installation [10/2015 - 05/2018]: Procedure

1. Press the front stabilizer bracket LH against the frame toward the outside of the vehicle and temporarily tighten the bolt (A).

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

2. Install the bolt (B), fully tighten the bolt (A), and then install the 2 bolts (C).

   Torque: 49 N*m (500 kgf*cm, 36 ft.*lbf) 

3. Install the wire harness clamp to the front stabilizer bracket LH.

1. Press the front stabilizer bracket RH against the frame toward the outside of the vehicle and temporarily tighten the bolt (A).

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

2. Install the bolt (B), fully tighten the bolt (A), and then install the 2 bolts (C).

   Torque: 49 N*m (500 kgf*cm, 36 ft.*lbf) 

3. Install the 2 wire harness clamps to the front stabilizer bracket RH.

1. Install the 2 front stabilizer bar bushings to the front stabilizer bar as shown in the illustration.

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   *a	Cutout
   *b	Bushing Stopper
   	Front of the Vehicle
   	Outside of the Vehicle

   NOTE:

   When installing the front stabilizer bar bushings, make sure that the cutout faces the front of the vehicle.

1. Install the front stabilizer bar to the vehicle so that the identification mark is positioned on the right side of the vehicle.

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   *a	Identification Mark
   	Front of the Vehicle
   	RH Side

1. Install the front No. 1 stabilizer bracket LH to the front stabilizer bracket LH with the 2 bolts.

   Torque: 49 N*m (500 kgf*cm, 36 ft.*lbf) 

HINT: 

Perform the same procedure as for the LH side.

Refer to PROCEDURE - Step 72

HINT: 

Perform the same procedure as for the LH side.

1. Install the front stabilizer link sub-assembly LH to the front stabilizer bar and front lower suspension arm assembly LH with the 2 nuts.

   Torque: 84 N*m (857 kgf*cm, 62 ft.*lbf) 

   HINT: 

   If the ball joint turns together with the nut, use a 6 mm hexagon wrench to hold the stud bolt.

HINT: 

Perform the same procedure as for the LH side.

1. Install the No. 2 frame crossmember assembly with the 3 bolts.

   Torque: 20 N*m (204 kgf*cm, 15 ft.*lbf) 

HINT: 

Perform the same procedure as for the No. 2 frame crossmember assembly.

1. Install the No. 1 oil cooler bracket with the bolt and 5 nuts.

   Bolt (A) 

   Torque: 8.0 N*m (82 kgf*cm, 71 in.*lbf) 

   Nut (B) 

   Torque: 8.0 N*m (82 kgf*cm, 71 in.*lbf) 

   Nut (C) 

   Torque: 11 N*m (112 kgf*cm, 8 ft.*lbf) 

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Install the oil cooler bracket with the bolt and 3 nuts.

   Torque: 8.0 N*m (82 kgf*cm, 71 in.*lbf) 

Refer to PROCEDURE - Step 70

HINT: 

Perform the same procedure as for the LH side.

Refer to PROCEDURE - Step 96

Refer to PROCEDURE - Step 1

Refer to ADJUSTMENT [10/2015 - ]