LEMON Manuals: Even more car manuals for everyone
Home >> Lexus >> 2016 >> GS 450h Base >> Repair and Diagnosis >> Accessories & Equipment >> Gauges & Instrument Panels >> Meter / Gauge System (Diagnostic Codes & Symptom Tests) >> Meter / Gauge System >> Vehicle Speed Signal Circuit [09/2014 - 10/2015] >> Procedure

Vehicle Speed Signal Circuit [09/2014 - 10/2015]: Procedure

  1. CHECK VEHICLE APPROACHING SPEAKER CONTROLLER 
    1. Disconnect the N40 combination meter assembly connector.
      GTY530251Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Disconnect the N68 multimedia module receiver connector.
    3. Disconnect the 4B junction block connector.
    4. Measure the voltage according to the value(s) in the table below.

      Standard Voltage

      Tester Connection Switch Condition Specified Condition
      N40-19 (+S) - Body ground Power switch on (IG) 4.5 to 14 V
      TEXT IN ILLUSTRATION

      *a Front view of wire harness connector
      (to Combination Meter Assembly)

    Result:  NG

    NG 

    See step  10

    Result:  OK

    OK 

    See step  2

  2. CHECK MULTI-MEDIA MODULE RECEIVER ASSEMBLY 
    • *1: w/ Night View System
    • *2: w/o Night View System
    1. Disconnect the N40 combination meter assembly connector.
      GTY530250Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Disconnect the T35*1 or T43*2 vehicle approaching speaker controller connector.
    3. Disconnect the 4B junction block connector.
    4. Measure the voltage according to the value(s) in the table below.

      Standard Voltage

      Tester Connection Switch Condition Specified Condition
      N40-19 (+S) - Body ground Power switch on (IG) 4.5 to 14 V
      TEXT IN ILLUSTRATION

      *a Front view of wire harness connector
      (to Combination Meter Assembly)

    Result:  NG

    NG 

    See step  11

    Result:  OK

    OK 

    See step  3

  3. CHECK POWER MANAGEMENT CONTROL ECU 
    1. Disconnect the 4B junction block connector.
      GTY526357Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage

      Tester Connection Switch Condition Specified Condition
      4B-5 - Body ground Power switch on (IG) 4.5 to 14 V
      TEXT IN ILLUSTRATION

      *a Front view of wire harness connector
      (to Cowl Side Junction Block RH)

    Result:  NG

    NG 

    See step  12

    Result:  OK

    OK 

    See step  4

  4. CHECK TELEMATICS TRANSCEIVER (DCM) 
    NOTE:

    For vehicles without a telematics transceiver, proceed to the next step.

    1. Disconnect the 4B junction block connector.
      GTY526357Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage

      Tester Connection Switch Condition Specified Condition
      4B-2 - Body ground Power switch on (IG) 4.5 to 14 V
      TEXT IN ILLUSTRATION

      *a Front view of wire harness connector
      (to Cowl Side Junction Block RH)

    Result:  NG

    NG 

    See step  13

    Result:  OK

    OK 

    See step  5

  5. CHECK STEREO COMPONENT AMPLIFIER ASSEMBLY 
    1. Disconnect the 4C junction block connector.
      GTY532520Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage

      Tester Connection Switch Condition Specified Condition
      4C-33 - Body ground Power switch on (IG) 4.5 to 14 V
      TEXT IN ILLUSTRATION

      *a Front view of wire harness connector
      (to Cowl Side Junction Block RH)

    Result:  NG

    NG 

    See step  14

    Result:  OK

    OK 

    See step  6

  6. CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - COWL SIDE JUNCTION BLOCK RH) 
    • *1: w/ Night View System
    • *2: w/o Night View System
    1. Disconnect the N40 combination meter assembly connector.
    2. Disconnect the 4B junction block connector.
    3. Disconnect the T35*1 or T43*2 vehicle approaching speaker controller connector.
    4. Disconnect the N68 multimedia module receiver connector.
    5. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      N40-19 (+S) - 4B-3 Always Below 1 Ω
      N40-19 (+S) - Body ground Always 10 kΩ or higher

    Result:  NG

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

    Result:  OK

    OK 

    See step  7

  7. INSPECT COWL SIDE JUNCTION BLOCK RH 
    1. Remove the cowl side junction block RH.
      GTY523980Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      4B-3 - 4B-5 Always Below 1 Ω
      4B-3 - 4B-2
      4B-3 - 4C-33

    Result:  NG

    NG 

    REPLACE COWL SIDE JUNCTION BLOCK RH 

    Result:  OK

    OK 

    See step  8

  8. CHECK COMBINATION METER ASSEMBLY 
    1. Disconnect the A14 skid control ECU assembly connector.
      GTY535445Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage

      Tester Connection Switch Condition Specified Condition
      A14-23 (SP1) - Body ground Power switch on (IG) 11 to 14 V
      TEXT IN ILLUSTRATION

      *a Front view of wire harness connector
      (to Skid Control ECU Assembly)

    Result:  NG

    NG 

    See step  15

    Result:  OK

    OK 

    See step  9

  9. CHECK COMBINATION METER ASSEMBLY 
    1. Remove the combination meter assembly with the connector(s) connected.
      GTY530999Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Connect an oscilloscope to terminal N40-20 (SI) and body ground.
    3. Check the signal waveform according to the condition(s) in the table below.
      MEASUREMENT CONDITION

      Item Condition
      Tester connection N40-20 (SI) - Body ground
      Tool setting 5 V/DIV., 20 ms/DIV.
      Vehicle condition Driving at approx. 20 km/h (12 mph)

      OK

      The waveform displayed is as shown in the illustration.

      TEXT IN ILLUSTRATION

      *a Component with harness connected
      (Combination Meter Assembly)

      HINT: 

      When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by (A) in the illustration narrows.

    Result:  OK

    OK 

    REPLACE COMBINATION METER ASSEMBLY 

    (Refer to REMOVAL [09/2014 - ] )

    Result:  NG

    NG 

    REPLACE SKID CONTROL ECU ASSEMBLY 

    (Refer to REMOVAL [09/2014 - ] )

  10. CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - VEHICLE APPROACHING SPEAKER CONTROLLER) 
    • *1: w/ Night View System
    • *2: w/o Night View System
    1. Disconnect the N40 combination meter assembly connector.
    2. Disconnect the T35*1 or T43*2 vehicle approaching speaker controller connector.
    3. Disconnect the N68 multimedia module receiver connector.
    4. Disconnect the 4B junction block connector.
    5. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      W/ NIGHT VIEW SYSTEM

      Tester Connection Condition Specified Condition
      N40-19 (+S) - T35-6 (SPD) Always Below 1 Ω
      N40-19 (+S) - Body ground Always 10 kΩ or higher
      W/O NIGHT VIEW SYSTEM

      Tester Connection Condition Specified Condition
      N40-19 (+S) - T43-6 (SPD) Always Below 1 Ω
      N40-19 (+S) - Body ground Always 10 kΩ or higher

    Result:  OK

    OK 

    REPLACE VEHICLE APPROACHING SPEAKER CONTROLLER 

    (Refer to REMOVAL [09/2014 - 10/2015] )

    Result:  NG

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

  11. CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - MULTI-MEDIA MODULE RECEIVER ASSEMBLY) 
    • *1: w/ Night View System
    • *2: w/o Night View System
    1. Disconnect the N40 combination meter assembly connector.
    2. Disconnect the N68 multimedia module receiver connector.
    3. Disconnect the T35*1 or T43*2 vehicle approaching speaker controller connector.
    4. Disconnect the 4B junction block connector.
    5. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      N40-19 (+S) - N68-56 (SPD) Always Below 1 Ω
      N40-19 (+S) - Body ground Always 10 kΩ or higher

    Result:  OK

    OK 

    REPLACE MULTI-MEDIA MODULE RECEIVER ASSEMBLY 

    (Refer to REMOVAL [09/2014 - ] )

    Result:  NG

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

  12. CHECK HARNESS AND CONNECTOR (COWL SIDE JUNCTION BLOCK RH - POWER MANAGEMENT CONTROL ECU) 
    1. Disconnect the 4B junction block connector.
    2. Disconnect the N91 power management control ECU connector.
    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      4B-5 - N91-16 (SPDI) Always Below 1 Ω
      4B-5 - Body ground Always 10 kΩ or higher

    Result:  OK

    OK 

    REPLACE POWER MANAGEMENT CONTROL ECU 

    (Refer to REMOVAL [09/2014 - ] )

    Result:  NG

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

  13. CHECK HARNESS AND CONNECTOR (COWL SIDE JUNCTION BLOCK RH - TELEMATICS TRANSCEIVER [DCM]) 
    1. Disconnect the 4B junction block connector.
    2. Disconnect the N87 telematics transceiver connector.
    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      4B-2 - N87-10 (SPDP) Always Below 1 Ω
      4B-2 - Body ground Always 10 kΩ or higher

    Result:  OK

    OK 

    REPLACE TELEMATICS TRANSCEIVER (DCM) 

    (Refer to REMOVAL [09/2014 - ] )

    Result:  NG

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

  14. CHECK HARNESS AND CONNECTOR (COWL SIDE JUNCTION BLOCK RH - STEREO COMPONENT AMPLIFIER ASSEMBLY) 
    1. Disconnect the 4C junction block connector.
    2. Disconnect the T40 stereo component amplifier assembly connector.
    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      4C-33 - T40-17 (SPD) Always Below 1 Ω
      4C-33 - Body ground Always 10 kΩ or higher

    Result:  OK

    OK 

    REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY 

    (Refer to REMOVAL [09/2014 - ] )

    Result:  NG

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

  15. CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - SKID CONTROL ECU ASSEMBLY) 
    1. Disconnect the N40 combination meter assembly connector.
    2. Disconnect the A14 skid control ECU assembly connector.
    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      N40-20 (SI) - A14-23 (SP1) Always Below 1 Ω
      N40-20 (SI) - Body ground Always 10 kΩ or higher

    Result:  OK

    OK 

    REPLACE COMBINATION METER ASSEMBLY 

    (Refer to REMOVAL [09/2014 - ] )

    Result:  NG

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

scientia non olet · About LEMON Manuals