DTC B1835-58: Short in Curtain Shield Squib LH Circuit; DTC B1836-58: Open in Curtain Shield Squib LH Circuit; DTC B1837-58: Short to GND in Curtain Shield Squib LH Circuit; DTC B1838-58: Short to B+ in Curtain Shield Squib LH Circuit [10/2014 - 05/2019]: Procedure

CHECK CURTAIN SHIELD AIRBAG ASSEMBLY LH

Turn the power switch off.

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

*1	Curtain Shield Airbag Assembly LH
*2	Airbag ECU Assembly
*3	Connector C
*4	SST
*a	Front view of wire harness connector (to Curtain Shield Airbag Assembly LH)

Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 90 seconds.
Disconnect the connectors from the curtain shield airbag assembly LH.
Connect the white wire side of SST (resistance: 2.1 Ω) to connector C.
WARNING:
Never connect the tester to the curtain shield airbag assembly LH for measurement, as this may lead to a serious injury due to airbag deployment.
NOTE:
- Do not forcibly insert SST into the terminals of the connector when connecting SST.
- Insert SST straight into the terminals of the connector.
- SST: 09843-18061
Connect the cable to the negative (-) auxiliary battery terminal, and wait for at least 2 seconds.
Turn the power switch on (IG), and wait for at least 60 seconds.
Clear the DTCs.
Refer to DTC CHECK / CLEAR [10/2014 - 05/2019]

Body Electrical > SRS Airbag > Clear DTCs
Turn the power switch off.
Turn the power switch on (IG), and wait for at least 60 seconds.

Check for DTCs.

Refer to DTC CHECK / CLEAR [10/2014 - 05/2019]

Body Electrical > SRS Airbag > Trouble Codes

Result

Proceed to
DTC B1835/58, B1836/58, B1837/58 or B1838/58 is not output
DTC B1835/58, B1836/58, B1837/58 or B1838/58 is output

HINT:

Codes other than DTC B1835/58, B1836/58, B1837/58 and B1838/58 may be output at this time, but they are not related to this check.

Turn the power switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 90 seconds.
Disconnect SST from connector C.

Result:

DTC B1835/58, B1836/58, B1837/58 or B1838/58 is not output

REPLACE CURTAIN SHIELD AIRBAG ASSEMBLY LH. Refer to REMOVAL [10/2014 - 09/2016] , or refer to REMOVAL [09/2016 - 05/2019]

Result:

DTC B1835/58, B1836/58, B1837/58 or B1838/58 is output

See step 2

CHECK CONNECTORS

Disconnect the connectors from the airbag ECU assembly.

Check that the connectors (on the airbag ECU assembly side and curtain shield airbag assembly LH side) are not damaged.

The lock button is not disengaged, and the claw of the lock is not deformed or damaged.

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

*1	Curtain Shield Airbag Assembly LH
*2	No. 2 Floor Wire
*3	Airbag ECU Assembly

Result

Proceed to
OK
NG

Result:

REPLACE NO. 2 FLOOR WIRE

Result:

See step 3

CHECK NO. 2 FLOOR WIRE

Connect the cable to the negative (-) auxiliary battery terminal, and wait for at least 2 seconds.

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

*1	Curtain Shield Airbag Assembly LH
*2	No. 2 Floor Wire
*3	Airbag ECU Assembly
*4	Connector C
*a	Front view of wire harness connector (to Curtain Shield Airbag Assembly LH)

Turn the power switch on (IG).

Measure the voltage according to the value(s) in the table below.

Standard Voltage

Tester Connection	Switch Condition	Specified Condition
Q10-1 (ICL+) - Body ground	Power switch on (IG)	Below 1 V
Q10-2 (ICL-) - Body ground	Power switch on (IG)	Below 1 V

Turn the power switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 90 seconds.

Measure the resistance according to the value(s) in the table below.

Standard Resistance

Tester Connection	Condition	Specified Condition
Q10-1 (ICL+) - Q10-2 (ICL-)	Always	Below 1 Ω

Release the activation prevention mechanism built into connector B.
Refer to DIAGNOSIS SYSTEM [10/2014 - ]

Measure the resistance according to the value(s) in the table below.

Standard Resistance

Tester Connection	Condition	Specified Condition
Q10-1 (ICL+) - Q10-2 (ICL-)	Always	1 MΩ or higher

Restore the released activation prevention mechanism of connector B to its original condition.

Measure the resistance according to the value(s) in the table below.

Standard Resistance

Tester Connection	Condition	Specified Condition
Q10-1 (ICL+) - Body ground	Always	1 MΩ or higher
Q10-2 (ICL-) - Body ground	Always	1 MΩ or higher

Result

Proceed to
OK
NG

Result:

REPLACE NO. 2 FLOOR WIRE

Result:

See step 4

CHECK DTC

Connect the connectors to the curtain shield airbag assembly LH and airbag ECU assembly.

*1	Curtain Shield Airbag Assembly LH
*2	Airbag ECU Assembly

Connect the cable to the negative (-) auxiliary battery terminal, and wait for at least 2 seconds.
Turn the power switch on (IG), and wait for at least 60 seconds.
Clear the DTCs.
Refer to DTC CHECK / CLEAR [10/2014 - 05/2019]

Body Electrical > SRS Airbag > Clear DTCs
Turn the power switch off.
Turn the power switch on (IG), and wait for at least 60 seconds.

Check for DTCs.

Refer to DTC CHECK / CLEAR [10/2014 - 05/2019]

Body Electrical > SRS Airbag > Trouble Codes

Result

Proceed to
DTC B1835/58, B1836/58, B1837/58 or B1838/58 is not output
DTC B1835/58, B1836/58, B1837/58 or B1838/58 is output

HINT:

Codes other than DTC B1835/58, B1836/58, B1837/58 and B1838/58 may be output at this time, but they are not related to this check.

Result:

DTC B1835/58, B1836/58, B1837/58 or B1838/58 is not output

USE SIMULATION METHOD TO CHECK. Refer to DIAGNOSIS SYSTEM [10/2014 - ]

Result:

DTC B1835/58, B1836/58, B1837/58 or B1838/58 is output

REPLACE AIRBAG ECU ASSEMBLY. Refer to REMOVAL [10/2014 - 05/2019]