Problem Symptoms Table [05/2019 - 07/2020]
NOTE:
- When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.
- w/ Pre-collision System:
When replacing the forward recognition camera, make sure to replace it with a new one.
- Recognition code registration is necessary when replacing the main body ECU (multiplex network body ECU).
- If the main body ECU (multiplex network body ECU) is replaced, refer to registration.
- After replacing the radio receiver assembly of vehicles subscribed to pay-type satellite radio broadcasts, XM radio ID registration is necessary (w/ SDARS System).
- Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed.
HINT:
- Use the table below to help determine the cause of problem symptoms. If multiple suspected areas are listed, the potential causes of the symptom are listed in order of probability in the "Suspected Area" column of the table. Check each symptom by checking the suspected areas in the order they are listed. Replace parts as necessary.
- Inspect the fuses and relays related to this system before inspecting the suspected areas below.
METER GAUGE
| Symptom | Suspected Area | Link |
|---|---|---|
| Speedometer malfunction | Refer to "Speedometer Malfunction" | Refer to Speedometer Malfunction [10/2014 - ] |
| Tachometer malfunction | Refer to "Tachometer Malfunction" | Refer to Tachometer Malfunction [10/2014 - ] |
| Fuel receiver gauge malfunction (Fuel receiver gauge is currently malfunctioning, or was malfunctioning in the past) |
Refer to "Fuel Receiver Gauge Display Malfunction" | Refer to Fuel Receiver Gauge Display Malfunction [10/2014 - ] |
| Engine coolant temperature receiver gauge malfunction | Refer to "Engine Coolant Temperature Receiver Gauge Malfunction" | Refer to Engine Coolant Temperature Receiver Gauge Malfunction [10/2014 - ] |
| Hybrid system indicator malfunction | Refer to "Hybrid System Indicator Malfunction" | Refer to Hybrid System Indicator Malfunction [10/2014 - ] |
WARNING LIGHT OR INDICATOR LIGHT
| Symptom | Suspected Area | Link |
|---|---|---|
| Turn indicator light does not come on (Turn signal light operates normally) | Perform Active Test [Turn Signal (Left) Indicator, Turn Signal (Right) Indicator] | Refer to DATA LIST / ACTIVE TEST [10/2014 - ] |
| Perform Data List [Turn Signal Switch (Right), Turn Signal Switch (Left)] | Refer to DATA LIST / ACTIVE TEST [10/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Front fog indicator light does not come on (Front fog light operates normally) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Perform Active Test [Indicat. Lamp Fr FOG] | Refer to DATA LIST / ACTIVE TEST [10/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Main body ECU (multiplex network body ECU) | Refer to REMOVAL [05/2019 - ] | |
| High beam indicator light does not come on (High beam headlight operates normally) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Perform Active Test [Indicat. Lamp Beam] | Refer to DATA LIST / ACTIVE TEST [10/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Main body ECU (multiplex network body ECU) | Refer to REMOVAL [05/2019 - ] | |
| Automatic high beam indicator light does not come on (w/ Automatic High Beam System) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Check indicator/warning light | Refer to OPERATION CHECK [10/2014 - ] | |
| Perform Active Test [Automatic High Beam Indicator] | Refer to DATA LIST / ACTIVE TEST [10/2014 - ] | |
| Automatic high beam system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Taillight indicator light does not come on (Taillight operates normally) (with km/h units) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Perform Active Test [Indicat. Lamp Tail] | Refer to REMOVAL [09/2017 - ] | |
| Main body ECU (multiplex network body ECU) | Refer to REMOVAL [05/2019 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Headlight indicator light does not come on (Headlight operates normally) (with mph units) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Perform Active Test [Indicat. Lamp Tail] | Refer to DATA LIST / ACTIVE TEST [10/2014 - ] | |
| Main body ECU (multiplex network body ECU) | Refer to REMOVAL [05/2019 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Driver seat belt warning light malfunction | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Perform Active Test [Driver Side Seat Belt] | Refer to DATA LIST / ACTIVE TEST [10/2014 - ] | |
| Proceed to "Driver Side Seat Belt Warning Light does not Operate" | Refer to Driver Side Seat Belt Warning Light does not Operate [05/2019 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Front passenger side seat belt warning light malfunction | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Proceed to "Front Passenger Side Seat Belt Warning Light Malfunction" | Refer to Front Passenger Side Seat Belt Warning Light Malfunction [05/2019 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| SRS warning light malfunction | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Check indicator/warning light | Refer to OPERATION CHECK [10/2014 - ] | |
| Perform Active Test [Indicat. Lamp Airbag] | Refer to DATA LIST / ACTIVE TEST [10/2014 - ] | |
| Proceed to "SRS Warning Light Remains ON" | Refer to SRS Warning Light Remains ON [05/2019 - ] | |
| Proceed to "SRS Warning Light does not Come ON" | Refer to SRS Warning Light does not Come ON [05/2019 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Master warning light (Other systems operate normally) | Check indicator/warning light | Refer to OPERATION CHECK [10/2014 - ] |
| Perform Active Test [Master Warning] | Refer to DATA LIST / ACTIVE TEST [10/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| MIL (Malfunction indicator light) malfunction | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Check indicator/warning light | Refer to OPERATION CHECK [10/2014 - ] | |
| Perform Active Test [Check Engine Indicator] | Refer to DATA LIST / ACTIVE TEST [10/2014 - ] | |
| Proceed to "MIL Circuit" | Refer to MIL Circuit [10/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| EPS warning light malfunction | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Check indicator/warning light | Refer to OPERATION CHECK [10/2014 - ] | |
| Perform Active Test [Indicat. EPS] | Refer to DATA LIST / ACTIVE TEST [10/2014 - ] | |
| Proceed to "Power Steering Warning Light Circuit" (for Manual Tilt and Manual Telescopic Steering Column) | Refer to Power Steering Warning Light Circuit [09/2017 - ] | |
| Proceed to "Power Steering Warning Light Circuit" (for Power Tilt and Power Telescopic Steering Column) | Refer to Power Steering Warning Light Circuit [09/2017 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Brake warning light malfunction | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Check indicator/warning light | Refer to OPERATION CHECK [10/2014 - ] | |
| Perform Active Test [Indicat. Lamp Brake] | Refer to DATA LIST / ACTIVE TEST [10/2014 - ] | |
| Proceed to "Brake Warning Light Remains ON" | Refer to Brake Warning Light Remains ON [10/2014 - ] | |
| Proceed to "Brake Warning Light does not Come ON" | Refer to Brake Warning Light does not Come ON [10/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Cruise indicator light does not come on | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Proceed to "Cruise Main Indicator Light Circuit" | Refer to Cruise Main Indicator Light Circuit [05/2019 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| SET indicator light does not come on | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Proceed to "Cruise SET Indicator Light Circuit" | Refer to Cruise SET Indicator Light Circuit [05/2019 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Radar cruise indicator light does not come on (w/ Dynamic Radar Cruise Control System) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Proceed to "Cruise Main Indicator Light Circuit" | Refer to Cruise Main Indicator Light Circuit [05/2019 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Lane tracing assist indicator light does not come on (w/ Lane tracing assist system) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Proceed to "Indicator Circuit" | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Steering indicator light does not come on (w/ Lane tracing assist system) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Lane tracing assist system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Forward recognition camera | Refer to REMOVAL [05/2019 - ] | |
| Tire pressure warning light malfunction | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Check indicator/warning light | Refer to OPERATION CHECK [10/2014 - ] | |
| Perform Active Test [Indicat. Tire Pressure Warning System] | Refer to DATA LIST / ACTIVE TEST [10/2014 - ] | |
| Proceed to "Tire Pressure Warning Light Circuit" | Refer to Tire Pressure Warning Light Circuit [05/2019 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Fuel level warning light does not come on (Fuel receiver gauge operates normally) | Perform Active Test [Indicat. Lamp Fuel] | Refer to DATA LIST / ACTIVE TEST [10/2014 - ] |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| ABS warning light malfunction | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Check indicator/warning light | Refer to OPERATION CHECK [10/2014 - ] | |
| Perform Active Test [Indicat. Lamp ABS] | Refer to DATA LIST / ACTIVE TEST [10/2014 - ] | |
| Proceed to "ABS Warning Light Remains ON" | Refer to ABS Warning Light Remains ON [10/2014 - ] | |
| Proceed to "ABS Warning Light does not Come ON" | Refer to ABS Warning Light does not Come ON [10/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| VSC OFF indicator light malfunction | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Check indicator/warning light | Refer to OPERATION CHECK [10/2014 - ] | |
| Perform Active Test [Indicat. VSC OFF] | Refer to DATA LIST / ACTIVE TEST [10/2014 - ] | |
| Proceed to "VSC OFF Switch Circuit" | Refer to VSC OFF Switch Circuit [10/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Slip indicator light does not come on | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Check indicator/warning light | Refer to OPERATION CHECK [10/2014 - ] | |
| Perform Active Test [Indicat. Lamp Slip] | Refer to DATA LIST / ACTIVE TEST [10/2014 - ] | |
| Proceed to "Slip Indicator Light Remains ON" | Refer to REMOVAL [09/2017 - ] | |
| Proceed to "Slip Indicator Light does not Come ON" | Refer to Slip Indicator Light does not Come ON [10/2014 - ] | |
| Combination meter assembly | Refer to Slip Indicator Light Remains ON [10/2014 - ] | |
| EPB* warning light does not come on | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Check indicator/warning light | Refer to OPERATION CHECK [10/2014 - ] | |
| Perform Active Test [Indicat. Park] | Refer to DATA LIST / ACTIVE TEST [10/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Parking brake ECU assembly | Refer to REMOVAL [05/2019 - ] | |
| PCS OFF indicator light malfunction (w/ Pre-collision System) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Check indicator/warning light | Refer to OPERATION CHECK [10/2014 - ] | |
| Perform Active Test [Indicat. Precrash] | Refer to DATA LIST / ACTIVE TEST [10/2014 - ] | |
| Pre-collision system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Forward recognition camera | Refer to REMOVAL [05/2019 - ] | |
| Clearance sonar indicator light does not come on (w/ Intuitive Parking Assist System) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Perform Active Test [Indicat. INTUITIVE P/A LCD] | Refer to DATA LIST / ACTIVE TEST [10/2014 - ] | |
| Intuitive parking assist system (w/ Intelligent Clearance Sonar System) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - ] | |
| Intuitive parking assist system (w/o Intelligent Clearance Sonar System) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 07/2020] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Clearance warning ECU assembly | Refer to REMOVAL [05/2019 - ] | |
| ICS OFF indicator light malfunction (w/ Intelligent Clearance Sonar System) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Intelligent clearance sonar system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Clearance warning ECU assembly | Refer to REMOVAL [05/2019 - ] | |
| Eco mode indicator light does not come on | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Hybrid control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Hybrid vehicle control ECU | Refer to REMOVAL [05/2019 - ] | |
| Sport mode indicator light does not come on | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Hybrid vehicle control ECU | Refer to REMOVAL [05/2019 - ] | |
| Brake hold standby indicator light does not come on | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Check indicator/warning light | Refer to OPERATION CHECK [10/2014 - ] | |
| Perform Active Test [Indicat. Brake Hold] | Refer to DATA LIST / ACTIVE TEST [10/2014 - ] | |
| Proceed to "Brake Hold Standby Indicator Light Circuit" | Refer to Brake Hold Standby Indicator Light Circuit [05/2019 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Brake hold operated indicator light does not come on | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Check indicator/warning light | Refer to OPERATION CHECK [10/2014 - ] | |
| Perform Active Test [Indicat. Hold] | Refer to DATA LIST / ACTIVE TEST [10/2014 - ] | |
| Proceed to "Brake Hold Operated Indicator Light Circuit" | Refer to Brake Hold Operated Indicator Light Circuit [05/2019 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| ECB* warning light does not come on | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Check indicator/warning light | Refer to OPERATION CHECK [10/2014 - ] | |
| Perform Active Test [Indicat. Lamp ECB] | Refer to DATA LIST / ACTIVE TEST [10/2014 - ] | |
| Electronically controlled brake system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Brake booster with master cylinder assembly (skid control ECU) | Refer to REMOVAL [05/2019 - ] | |
| READY indicator light does not come on | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Perform Active Test [Indicat. Ready (HV)] | Refer to DATA LIST / ACTIVE TEST [10/2014 - ] | |
| Hybrid control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Hybrid vehicle control ECU | Refer to REMOVAL [05/2019 - ] | |
| EV indicator light does not come on | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Check customize setting | Refer to CUSTOMIZE PARAMETERS [10/2014 - ] | |
| Perform Active Test [EV Mode Indicator] | Refer to DATA LIST / ACTIVE TEST [10/2014 - ] | |
| Hybrid control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Hybrid vehicle control ECU | Refer to REMOVAL [05/2019 - ] | |
| EV mode indicator light does not come on | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Hybrid control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Hybrid vehicle control ECU | Refer to REMOVAL [05/2019 - ] |
MULTI-INFORMATION DISPLAY
| Symptom | Suspected Area | Link |
|---|---|---|
| "Opening" display malfunction | Combination meter assembly | Refer to REMOVAL [09/2017 - ] |
| "Each door ajar" display malfunction (Door courtesy switch, back door courtesy switch or hood courtesy switch is normal) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Main body ECU (multiplex network body ECU) | Refer to REMOVAL [05/2019 - ] | |
| "Outside temp" display malfunction*A | Proceed to "Ambient Temperature Display System" | Refer to Ambient Temperature Display System [05/2019 - ] |
| Icy street warning display malfunction | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Air conditioning system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Air conditioning amplifier assembly | Refer to REMOVAL [09/2017 - ] | |
| "Windshield Washer Fluid Low" display malfunction | Proceed to "Washer Fluid Level Warning Switch Circuit" | Refer to Washer Fluid Level Warning Switch Circuit [10/2014 - ] |
| "Current fuel consumption" display malfunction (Combination meter assembly operates normally) | Combination meter assembly | Refer to REMOVAL [09/2017 - ] |
| "Average fuel consumption (After refuel)" display malfunction (Combination meter assembly operates normally) | Combination meter assembly | Refer to REMOVAL [09/2017 - ] |
| "Average fuel consumption (After reset)" display malfunction (Combination meter assembly operates normally) | Combination meter assembly | Refer to REMOVAL [09/2017 - ] |
| "Average fuel consumption (After start)" display malfunction (Combination meter assembly operates normally) | Combination meter assembly | Refer to REMOVAL [09/2017 - ] |
| "Average speed (After start)" display malfunction (Combination meter assembly operates normally) | Combination meter assembly | Refer to REMOVAL [09/2017 - ] |
| "Average speed (After reset)" display malfunction (Combination meter assembly operates normally) | Combination meter assembly | Refer to REMOVAL [09/2017 - ] |
| "Elapsed time (After reset)" display malfunction (Combination meter assembly operates normally) | Combination meter assembly | Refer to REMOVAL [09/2017 - ] |
| "Elapsed time (After start)" display malfunction (Combination meter assembly operates normally) | Combination meter assembly | Refer to REMOVAL [09/2017 - ] |
| "Distance (Range)" display malfunction (Combination meter assembly operates normally) | Combination meter assembly | Refer to REMOVAL [09/2017 - ] |
| "Distance (After start)" display malfunction (Combination meter assembly operates normally) | Combination meter assembly | Refer to REMOVAL [09/2017 - ] |
| "Energy flow display" display malfunction | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Hybrid control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] | |
| Hybrid battery system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Tire pressure display malfunction | Tire pressure warning system | Refer to REMOVAL [05/2019 - ] |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| "Navigation tab" display malfunction (except 8 Speakers) | Navigation system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - ] |
| Audio and visual system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Radio receiver assembly | Refer to REMOVAL [05/2019 - ] | |
| "Audio tab" display malfunction | Navigation system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - ] |
| Audio and visual system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Radio receiver assembly | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] | |
| "Radar cruise control / Lane tracing assist displayed tab" display malfunction (w/ Dynamic Radar Cruise Control System or Lane tracing assist system) | Combination meter assembly | Refer to REMOVAL [09/2017 - ] |
| Forward recognition camera | Refer to REMOVAL [05/2019 - ] | |
| "Message tab" display malfunction | Combination meter assembly | Refer to REMOVAL [09/2017 - ] |
| "Setting tab" display malfunction | Combination meter assembly | Refer to REMOVAL [09/2017 - ] |
| "Shift selector" display malfunction | Perform Active Test [A/T Indicator Operation 1, A/T Indicator Operation 2, A/T Indicator Operation 3] | Refer to DATA LIST / ACTIVE TEST [10/2014 - ] |
| Hybrid control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Hybrid vehicle control ECU | Refer to REMOVAL [05/2019 - ] | |
| "SPORT indicator" display malfunction | Hybrid control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Hybrid vehicle control ECU | Refer to REMOVAL [05/2019 - ] | |
| "SPORT S indicator" display malfunction | Hybrid control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Hybrid vehicle control ECU | Refer to REMOVAL [05/2019 - ] | |
| "SPORT S+ indicator" display malfunction | Hybrid control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Hybrid vehicle control ECU | Refer to REMOVAL [05/2019 - ] | |
| "Fuel Low" display malfunction (Fuel receiver gauge operates normally) | Combination meter assembly | Refer to REMOVAL [09/2017 - ] |
| "AWD TEST MODE" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (for AWD) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Hybrid control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Hybrid vehicle control ECU | Refer to REMOVAL [05/2019 - ] | |
| "CDY-2" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (for AWD) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Hybrid control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Hybrid vehicle control ECU | Refer to REMOVAL [05/2019 - ] | |
| "CDY-4" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (for AWD) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Hybrid control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Hybrid vehicle control ECU | Refer to REMOVAL [05/2019 - ] | |
| "2WD MAINTENANCE MODE" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (for AWD) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Hybrid control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Hybrid vehicle control ECU | Refer to REMOVAL [09/2017 - ] | |
| "AWD MAINTENANCE MODE" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (for AWD) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Hybrid control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Hybrid vehicle control ECU | Refer to REMOVAL [05/2019 - ] | |
| "2WD CERTIFICATION MODE" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (for AWD) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Hybrid control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Hybrid vehicle control ECU | Refer to REMOVAL [05/2019 - ] | |
| "AWD CERTIFICATION MODE" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (for AWD) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Hybrid control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Hybrid vehicle control ECU | Refer to REMOVAL [05/2019 - ] | |
| "AWD System Malfunction 2WD Mode Engaged Visit Your Dealer" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (for AWD) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Hybrid control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Hybrid vehicle control ECU | Refer to REMOVAL [05/2019 - ] | |
| "AWD System Overheated 2WD Mode Engaged" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (for AWD) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Hybrid control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Hybrid vehicle control ECU | Refer to REMOVAL [05/2019 - ] | |
| "AWD System Overheated Switching to 2WD Mode" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (for AWD) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Hybrid control system | Refer to REMOVAL [09/2017 - ] | |
| Combination meter assembly | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] | |
| Hybrid vehicle control ECU | Refer to REMOVAL [05/2019 - ] | |
| "Push and Hold Power Switch for Emergency Stop" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Smart access system with push-button start (for Entry Function) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] | |
| Smart access system with push-button start (for Start Function) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Certification ECU (smart key ECU assembly) | Refer to REMOVAL [10/2014 - ] | |
| "Shift to N and Press Power Switch to Restart" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Smart access system with push-button start (for Entry Function) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] | |
| Smart access system with push-button start (for Start Function) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Certification ECU (smart key ECU assembly) | Refer to REMOVAL [10/2014 - ] | |
| "Power Turned Off to Save Battery" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Certification ECU (smart key ECU assembly) | Refer to REMOVAL [10/2014 - ] | |
| "Key Not Detected Check Key Location" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Smart access system with push-button start (for Entry Function) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] | |
| Smart access system with push-button start (for Start Function) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Certification ECU (smart key ECU assembly) | Refer to REMOVAL [10/2014 - ] | |
| "Smart Access System Malfunction See Owner's Manual" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Smart access system with push-button start (for Entry Function) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] | |
| Smart access system with push-button start (for Start Function) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Certification ECU (smart key ECU assembly) | Refer to REMOVAL [10/2014 - ] | |
| "Turn Off Vehicle" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Smart access system with push-button start (for Entry Function) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] | |
| Smart access system with push-button start (for Start Function) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Certification ECU (smart key ECU assembly) | Refer to REMOVAL [10/2014 - ] | |
| "Key Left inside Vehicle" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Smart access system with push-button start (for Entry Function) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Certification ECU (smart key ECU assembly) | Refer to REMOVAL [10/2014 - ] | |
| "Depress Brake and Then Touch Key to Power Switch" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Smart access system with push-button start (for Entry Function) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] | |
| Smart access system with push-button start (for Start Function) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Certification ECU (smart key ECU assembly) | Refer to REMOVAL [10/2014 - ] | |
| "Depress Brake and Power to Start" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Smart access system with push-button start (for Entry Function) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] | |
| Smart access system with push-button start (for Start Function) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Certification ECU (smart key ECU assembly) | Refer to REMOVAL [10/2014 - ] | |
| "Key Battery Low" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Smart access system with push-button start (for Entry Function) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Certification ECU (smart key ECU assembly) | Refer to REMOVAL [10/2014 - ] | |
| "IGNITION ON" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Smart access system with push-button start (for Entry Function) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] | |
| Smart access system with push-button start (for Start Function) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Certification ECU (smart key ECU assembly) | Refer to REMOVAL [10/2014 - ] | |
| "Steering Wheel Lock Press Power Switch while Turning Wheel" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Steering lock system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Certification ECU (smart key ECU assembly) | Refer to REMOVAL [10/2014 - ] | |
| "Shift to P Before Exiting Vehicle" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Hybrid control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Hybrid vehicle control ECU | Refer to REMOVAL [05/2019 - ] | |
| "To Start Vehicle, Put Shift Lever into P" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Hybrid control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Hybrid vehicle control ECU | Refer to REMOVAL [05/2019 - ] | |
| "Hybrid System Stopped Shift to P" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Hybrid control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Hybrid vehicle control ECU | Refer to REMOVAL [05/2019 - ] | |
| "Hybrid System Stopped Stop in a Safe Place" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Hybrid control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Hybrid vehicle control ECU | Refer to REMOVAL [05/2019 - ] | |
| "Switch to Brake" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Intelligent clearance sonar system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Clearance warning ECU assembly | Refer to REMOVAL [05/2019 - ] | |
| "Object Detected Acceleration Reduced" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Intelligent clearance sonar system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Clearance warning ECU assembly | Refer to REMOVAL [05/2019 - ] | |
| "Accelerator Stuck Depress Brake to Stop" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Hybrid control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Hybrid vehicle control ECU | Refer to REMOVAL [05/2019 - ] | |
| "Release Accelerator" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Hybrid control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Hybrid vehicle control ECU | Refer to REMOVAL [05/2019 - ] | |
| "Hybrid System Malfunction Do Not Be Towed" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Hybrid control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Hybrid vehicle control ECU | Refer to REMOVAL [05/2019 - ] | |
| "Shift Is in N Release Accelerator Before Shifting" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Hybrid control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Hybrid vehicle control ECU | Refer to REMOVAL [05/2019 - ] | |
| "Depress Brake When Vehicle Is Stopped Hybrid System May Overheat" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Hybrid control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Hybrid vehicle control ECU | Refer to REMOVAL [05/2019 - ] | |
| "Hybrid Battery Low Hybrid System Stopped Shift to P and Restart" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Hybrid control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Hybrid vehicle control ECU | Refer to REMOVAL [05/2019 - ] | |
| "Hybrid System Malfunction" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Hybrid control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Hybrid vehicle control ECU | Refer to REMOVAL [05/2019 - ] | |
| "Check Engine" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Hybrid control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Hybrid vehicle control ECU | Refer to REMOVAL [05/2019 - ] | |
| "Hybrid Battery System Malfunction" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Hybrid control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Hybrid vehicle control ECU | Refer to REMOVAL [05/2019 - ] | |
| "Accelerator System Malfunction" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Hybrid control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Hybrid vehicle control ECU | Refer to REMOVAL [05/2019 - ] | |
| "Hybrid Battery Low Shift Out of N to Recharge" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Hybrid control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Hybrid vehicle control ECU | Refer to REMOVAL [05/2019 - ] | |
| "Check Engine Visit Your Dealer" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| SFI system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| ECM | Refer to REMOVAL [10/2014 - ] | |
| "Check Engine Reduced Engine Power Visit Your Dealer" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| SFI system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| ECM | Refer to REMOVAL [10/2014 - ] | |
| "Engine Coolant Temp High Stop in a Safe Place See Owner's Manual" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| SFI system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| ECM | Refer to REMOVAL [10/2014 - ] | |
| "Oil Maintenance Required Soon" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (with mph units) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| SFI system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| ECM | Refer to REMOVAL [10/2014 - ] | |
| "Maintenance Required Soon" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (with mph units) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| SFI system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| ECM | Refer to REMOVAL [10/2014 - ] | |
| "Injector Maintenance Required Soon" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (with mph units) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] |
| SFI system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| ECM | Refer to REMOVAL [10/2014 - ] | |
| "Oil Maintenance Required Visit Your Dealer" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (with mph units) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| SFI system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| ECM | Refer to REMOVAL [10/2014 - ] | |
| "Maintenance Required Visit Your Dealer" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (with mph units) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| SFI system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] | |
| Combination meter assembly | Refer to DATA LIST / ACTIVE TEST [10/2014 - ] | |
| ECM | Refer to REMOVAL [10/2014 - ] | |
| "Injector Maintenance Required Visit Your Dealer" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (with mph units) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] |
| SFI system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [05/2019 - ] | |
| ECM | Refer to REMOVAL [10/2014 - ] | |
| "Drive-Start Control Malfunction Visit Your Dealer" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Hybrid control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Hybrid vehicle control ECU | Refer to REMOVAL [05/2019 - ] | |
| "Brake Override Malfunction Visit Your Dealer" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Hybrid control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Hybrid vehicle control ECU | Refer to REMOVAL [05/2019 - ] | |
| "Accelerator and Brake Pedals Depressed Simultaneously" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Hybrid control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Hybrid vehicle control ECU | Refer to REMOVAL [05/2019 - ] | |
| "Hybrid System Overheated Reduced Output Power" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Hybrid control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Hybrid vehicle control ECU | Refer to REMOVAL [05/2019 - ] | |
| "Maintenance required for hybrid battery cooling parts at your dealer" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Hybrid control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Hybrid vehicle control ECU | Refer to REMOVAL [05/2019 - ] | |
| "Aux Battery Low See Owner's Manual" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Hybrid control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Hybrid vehicle control ECU | Refer to REMOVAL [05/2019 - ] | |
| "EV Mode Unavailable" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Hybrid control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Hybrid vehicle control ECU | Refer to REMOVAL [05/2019 - ] | |
| "EV Mode Unavailable System Warming Up" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Hybrid control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Hybrid vehicle control ECU | Refer to REMOVAL [05/2019 - ] | |
| "EV Mode Unavailable Hybrid Battery Low" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Hybrid control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Hybrid vehicle control ECU | Refer to REMOVAL [05/2019 - ] | |
| "EV Mode Unavailable Speed Range Exceeded" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Hybrid control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Hybrid vehicle control ECU | Refer to REMOVAL [05/2019 - ] | |
| "EV Mode Unavailable Reduce Acceleration to Activate" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Hybrid control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Hybrid vehicle control ECU | Refer to REMOVAL [05/2019 - ] | |
| "EV Mode Deactivated" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Hybrid control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Hybrid vehicle control ECU | Refer to REMOVAL [05/2019 - ] | |
| "EV Mode Deactivated Speed Range Exceeded" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Hybrid control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Hybrid vehicle control ECU | Refer to REMOVAL [05/2019 - ] | |
| "EV Mode Deactivated Hybrid Battery Low" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Hybrid control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Hybrid vehicle control ECU | Refer to REMOVAL [05/2019 - ] | |
| "EV Mode Deactivated Accelerator Depressed Too Far" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Hybrid control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Hybrid vehicle control ECU | Refer to REMOVAL [05/2019 - ] | |
| "Low Oil Pressure Stop in a Safe Place See Owner's Manual" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | Engine oil pressure switch | Refer to INSPECTION [10/2014 - ] |
| Harness or connector | - | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| "Antilock Brake System Malfunction Visit Your Dealer" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Electronically controlled brake system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Brake booster with master cylinder assembly (skid control ECU) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] | |
| "Braking Power Low Stop in a Safe Place See Owner's Manual" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Electronically controlled brake system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Brake booster with master cylinder assembly (skid control ECU) | Refer to REMOVAL [05/2019 - ] | |
| "Traction Control Turned Off" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Electronically controlled brake system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Brake booster with master cylinder assembly (skid control ECU) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] | |
| "Brake Hold Warning Depress Brake on Slope" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Electronically controlled brake system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Brake booster with master cylinder assembly (skid control ECU) | Refer to REMOVAL [05/2019 - ] | |
| "Brake Hold Malfunction Visit Your Dealer" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Electronically controlled brake system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Brake booster with master cylinder assembly (skid control ECU) | Refer to REMOVAL [05/2019 - ] | |
| "Brake Hold Less Effective during Icy Conditions" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Electronically controlled brake system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Brake booster with master cylinder assembly (skid control ECU) | Refer to REMOVAL [05/2019 - ] | |
| "Brake Hold Active Depress Brake and Switch to Deactivate" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Electronically controlled brake system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Brake booster with master cylinder assembly (skid control ECU) | Refer to REMOVAL [05/2019 - ] | |
| "Brake Hold Unavailable Driver Door Open" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Electronically controlled brake system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Brake booster with master cylinder assembly (skid control ECU) | Refer to REMOVAL [05/2019 - ] | |
| "Brake Hold Unavailable Driver Seat Belt Unbuckled" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Electronically controlled brake system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Brake booster with master cylinder assembly (skid control ECU) | Refer to REMOVAL [05/2019 - ] | |
| "Brake Hold Unavailable Hood or Trunk Open" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Electronically controlled brake system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Brake booster with master cylinder assembly (skid control ECU) | Refer to REMOVAL [05/2019 - ] | |
| "Depress Brake to Maintain Brake Hold" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Electronically controlled brake system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Brake booster with master cylinder assembly (skid control ECU) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] | |
| "Close Driver Door to Maintain Brake Hold" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Electronically controlled brake system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Brake booster with master cylinder assembly (skid control ECU) | Refer to REMOVAL [05/2019 - ] | |
| "Fasten Driver Seat Belt to Maintain Brake Hold" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Electronically controlled brake system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Brake booster with master cylinder assembly (skid control ECU) | Refer to REMOVAL [05/2019 - ] | |
| "Braking Power Low Visit Your Dealer" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Electronically controlled brake system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Brake booster with master cylinder assembly (skid control ECU) | Refer to REMOVAL [05/2019 - ] | |
| "Release Parking Brake" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Electrical parking brake system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Parking brake ECU assembly | Refer to REMOVAL [05/2019 - ] | |
| "Vehicle May Roll Shift to P" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Electrical parking brake system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Parking brake ECU assembly | Refer to REMOVAL [05/2019 - ] | |
| "Release Parking Brake while Depressing Brake" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Electrical parking brake system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Parking brake ECU assembly | Refer to REMOVAL [05/2019 - ] | |
| "Parking Brake Overheated Parking Brake Unavailable" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Electrical parking brake system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Parking brake ECU assembly | Refer to REMOVAL [05/2019 - ] | |
| "Parking Brake Unavailable" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Electrical parking brake system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Parking brake ECU assembly | Refer to REMOVAL [05/2019 - ] | |
| "Electronic Parking Brake Malfunction Visit Your Dealer" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Electrical parking brake system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Parking brake ECU assembly | Refer to REMOVAL [05/2019 - ] | |
| "Parking Brake Activated Release Before Driving" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Electrical parking brake system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Parking brake ECU assembly | Refer to REMOVAL [05/2019 - ] | |
| "Brake Hold Unavailable" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Electronically controlled brake system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Brake booster with master cylinder assembly (skid control ECU) | Refer to REMOVAL [05/2019 - ] | |
| "Brake Hold Deactivted" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Electronically controlled brake system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Brake booster with master cylinder assembly (skid control ECU) | Refer to REMOVAL [05/2019 - ] | |
| "Automatic Mode On Shift Operation Sets or Releases Parking Brake" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Electrical parking brake system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Parking brake ECU assembly | Refer to REMOVAL [05/2019 - ] | |
| "Automatic Mode Off" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Electrical parking brake system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Parking brake ECU assembly | Refer to REMOVAL [05/2019 - ] | |
| "Power Steering Malfunction Steering Power Low Visit Your Dealer" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Power steering system (for Manual Tilt and Manual Telescopic Steering Column) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - ] | |
| Power steering system (for Power Tilt and Power Telescopic Steering Column) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Power steering ECU assembly | Refer to REMOVAL [10/2014 - ] | |
| "Steering Power Low Visit Your Dealer" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Power steering system (for Manual Tilt and Manual Telescopic Steering Column) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - ] | |
| Power steering system (for Power Tilt and Power Telescopic Steering Column) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Power steering ECU assembly | Refer to REMOVAL [10/2014 - ] | |
| "Power Steering Malfunction Visit Your Dealer" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Power steering system (for Manual Tilt and Manual Telescopic Steering Column) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - ] | |
| Power steering system (for Power Tilt and Power Telescopic Steering Column) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Power steering ECU assembly | Refer to REMOVAL [10/2014 - ] | |
| "Hybrid System Stopped Steering Power Low" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Power steering system (for Manual Tilt and Manual Telescopic Steering Column) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - ] | |
| Power steering system (for Power Tilt and Power Telescopic Steering Column) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Power steering ECU assembly | Refer to REMOVAL [10/2014 - ] | |
| "SRS Airbag System Malfunction Visit Your Dealer" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Airbag system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Airbag ECU assembly | Refer to REMOVAL [05/2019 - ] | |
| "Turn Lights Off" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Lighting system (for Triple Beam Headlight) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] | |
| Lighting system (for Single Beam Headlight) | Refer to REMOVAL [05/2019 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Main body ECU (multiplex network body ECU) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - ] | |
| "Headlight System Malfunction Visit Your Dealer" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Lighting system (for Triple Beam Headlight) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] | |
| Lighting system (for Single Beam Headlight) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] | |
| Automatic high beam level control system (w/ Automatic High Beam Level Control System) | Refer to REMOVAL [05/2019 - ] | |
| Automatic high beam system (w/ Automatic High Beam System) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Headlight light control ECU sub-assembly | Refer to REMOVAL [09/2017 - ] | |
| "To Activate Auto High Beam, Switch Headlights to High Beam" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Automatic High Beam System) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Automatic high beam system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Headlight light control ECU sub-assembly | Refer to REMOVAL [09/2017 - ] | |
| Pre-collision display is not displayed (w/ Pre-collision System) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Pre-collision system | Refer to REMOVAL [05/2019 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Forward recognition camera | Refer to REMOVAL [05/2019 - ] | |
| "BRAKE !" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Pre-collision System) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Pre-collision system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Forward recognition camera | Refer to REMOVAL [05/2019 - ] | |
| "VSC Turned Off Pre-collision Brake System Unavailable" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Pre-collision System) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Pre-collision system | Refer to REMOVAL [05/2019 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Forward recognition camera | Refer to REMOVAL [05/2019 - ] | |
| "Pre-collision System Malfunction Visit Your Dealer" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Pre-collision System) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Pre-collision system | Refer to REMOVAL [05/2019 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Forward recognition camera | Refer to REMOVAL [05/2019 - ] | |
| "Pre-collision System Unavailable" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Pre-collision System) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Pre-collision system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Forward recognition camera | Refer to REMOVAL [05/2019 - ] | |
| "Pre-collision System Turned Off" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Pre-collision System) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Pre-collision system | Refer to REMOVAL [05/2019 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Forward recognition camera | Refer to REMOVAL [05/2019 - ] | |
| "Front Camera Unavailable" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Pre-collision System) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Pre-collision system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Forward recognition camera | Refer to REMOVAL [05/2019 - ] | |
| "Front Camera Vision Blocked Clean and Demist Windshield" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Pre-collision System) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Pre-collision system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Forward recognition camera | Refer to REMOVAL [05/2019 - ] | |
| "RADAR READY" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Dynamic Radar Cruise Control System) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Dynamic radar cruise control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Forward recognition camera | Refer to REMOVAL [05/2019 - ] | |
| "Operate Cruise Lever or Accelerator Pedal to Resume" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Dynamic Radar Cruise Control System) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Dynamic radar cruise control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Forward recognition camera | Refer to REMOVAL [05/2019 - ] | |
| "CRUISE NOT AVAILABLE" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Dynamic Radar Cruise Control System) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Dynamic radar cruise control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Forward recognition camera | Refer to REMOVAL [05/2019 - ] | |
| "PRECEDING VEHICLE MOVEMENT" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Dynamic Radar Cruise Control System) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Dynamic radar cruise control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Forward recognition camera | Refer to REMOVAL [05/2019 - ] | |
| "WAITING" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Dynamic Radar Cruise Control System) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Dynamic radar cruise control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Forward recognition camera | Refer to REMOVAL [05/2019 - ] | |
| "Mute PKSA Temporarily" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Pre-collision System) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Intuitive parking assist system (w/ Intelligent Clearance Sonar System) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - ] | |
| Intuitive parking assist system (w/o Intelligent Clearance Sonar System) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 07/2020] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Clearance warning ECU assembly | Refer to REMOVAL [05/2019 - ] | |
| "PKSA Muted Temporarily" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Pre-collision System) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Intuitive parking assist system (w/ Intelligent Clearance Sonar System) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - ] | |
| Intuitive parking assist system (w/o Intelligent Clearance Sonar System) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 07/2020] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Clearance warning ECU assembly | Refer to REMOVAL [05/2019 - ] | |
| "ADJUSTING LTA CAMERA" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Lane tracing assist system) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Lane tracing assist system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Forward recognition camera | Refer to REMOVAL [05/2019 - ] | |
| "Hold Steering Wheel" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Lane tracing assist system) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Lane tracing assist system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Forward recognition camera | Refer to REMOVAL [05/2019 - ] | |
| "LTA Steering Assist Unavailable Hold Steering Wheel" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Lane tracing assist system) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Lane tracing assist system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Forward recognition camera | Refer to REMOVAL [05/2019 - ] | |
| Lane tracing assist display is not displayed (w/ Lane tracing assist system) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Lane tracing assist system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Forward recognition camera | Refer to REMOVAL [05/2019 - ] | |
| "Lane tracing assist Malfunction Visit Your Dealer" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Lane tracing assist system) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Lane tracing assist system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Forward recognition camera | Refer to REMOVAL [05/2019 - ] | |
| "Lane tracing assist Unavailable Camera Overheated" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Lane tracing assist system) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Lane tracing assist system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Forward recognition camera | Refer to REMOVAL [05/2019 - ] | |
| "LTA Steering Assist Deactivated Warnings Available" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Lane tracing assist system) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Lane tracing assist system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Forward recognition camera | Refer to REMOVAL [05/2019 - ] | |
| "Lane tracing assist Turned On Steering Assist Active" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Lane tracing assist system) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Lane tracing assist system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Forward recognition camera | Refer to REMOVAL [05/2019 - ] | |
| "Lane tracing assist Turned On Steering Assist Inactive" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Lane tracing assist system) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Lane tracing assist system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Forward recognition camera | Refer to REMOVAL [05/2019 - ] | |
| "Lane tracing assist Unavailable Below Approx 50km/h" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Lane tracing assist system) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Lane tracing assist system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Forward recognition camera | Refer to REMOVAL [05/2019 - ] | |
| "Lane tracing assist Unavailable Below Approx 32MPH" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Lane tracing assist system) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Lane tracing assist system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Forward recognition camera | Refer to REMOVAL [05/2019 - ] | |
| "Lane tracing assist Unavailable at Current Speed" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Lane tracing assist system) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Lane tracing assist system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Forward recognition camera | Refer to REMOVAL [05/2019 - ] | |
| Dynamic radar cruise display is not displayed (w/ Dynamic Radar Cruise Control System) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Dynamic radar cruise control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Forward recognition camera | Refer to REMOVAL [05/2019 - ] | |
| "Would You Like to Take a Rest?" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Lane tracing assist system) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Lane tracing assist system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Forward recognition camera | Refer to REMOVAL [05/2019 - ] | |
| "Please Take a Rest" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Lane tracing assist system) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Lane tracing assist system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Forward recognition camera | Refer to REMOVAL [05/2019 - ] | |
| "ADJUSTING FRONT RADAR BEAM" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Dynamic Radar Cruise Control System) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Dynamic radar cruise control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Forward recognition camera | Refer to REMOVAL [05/2019 - ] | |
| "CHECKING CRUISE CONTROL C/D" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Dynamic radar cruise control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] | |
| Dynamic radar cruise control system (w/ Dynamic Radar Cruise Control System) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Hybrid vehicle control ECU | Refer to REMOVAL [05/2019 - ] | |
| Forward recognition camera (w/ Dynamic Radar Cruise Control System) | Refer to REMOVAL [05/2019 - ] | |
| "CHECKING CRUISE CONTROL BRAKE" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Dynamic radar cruise control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] | |
| Dynamic radar cruise control system (w/ Dynamic Radar Cruise Control System) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Hybrid vehicle control ECU | Refer to REMOVAL [05/2019 - ] | |
| Forward recognition camera (w/ Dynamic Radar Cruise Control System) | Refer to REMOVAL [05/2019 - ] | |
| "Radar Cruise Control Unavailable Clean Sensor" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Dynamic Radar Cruise Control System) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Dynamic radar cruise control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Forward recognition camera | Refer to REMOVAL [05/2019 - ] | |
| "Radar Cruise Control Unavailable" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Dynamic Radar Cruise Control System) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Dynamic radar cruise control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Forward recognition camera | Refer to REMOVAL [05/2019 - ] | |
| "Radar Cruise Control Unavailable Depress Brake to Resume Driving" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Dynamic Radar Cruise Control System) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Dynamic radar cruise control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Forward recognition camera | Refer to REMOVAL [05/2019 - ] | |
| "Radar Cruise Active Please Pay Attention to Other Vehicles" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Dynamic Radar Cruise Control System) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Dynamic radar cruise control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Forward recognition camera | Refer to REMOVAL [05/2019 - ] | |
| "Cruise Control Malfunction Visit Your Dealer" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Dynamic radar cruise control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] | |
| Dynamic radar cruise control system (w/ Dynamic Radar Cruise Control System) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Hybrid vehicle control ECU | Refer to REMOVAL [05/2019 - ] | |
| Forward recognition camera (w/ Dynamic Radar Cruise Control System) | Refer to REMOVAL [05/2019 - ] | |
| "Cruise Control Fault Press Brake to Deactivate Visit Your Dealer" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Dynamic radar cruise control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] | |
| Dynamic radar cruise control system (w/ Dynamic Radar Cruise Control System) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Hybrid vehicle control ECU | Refer to REMOVAL [05/2019 - ] | |
| Forward recognition camera (w/ Dynamic Radar Cruise Control System) | Refer to REMOVAL [05/2019 - ] | |
| Intuitive parking assist display is not displayed (w/ Intuitive Parking Assist System) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Intuitive parking assist system (w/ Intelligent Clearance Sonar System) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - ] | |
| Intuitive parking assist system (w/o Intelligent Clearance Sonar System) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 07/2020] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Clearance warning ECU assembly | Refer to REMOVAL [05/2019 - ] | |
| "Parking Assist Malfunction Vist Your Dealer" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Intuitive Parking Assist System) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Intuitive parking assist system (w/ Intelligent Clearance Sonar System) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - ] | |
| Intuitive parking assist system (w/o Intelligent Clearance Sonar System) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 07/2020] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Clearance warning ECU assembly | Refer to REMOVAL [05/2019 - ] | |
| "Parking Assist Unavailable Clean Parking Assist Sensor" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Intuitive Parking Assist System) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] |
| Intuitive parking assist system (w/ Intelligent Clearance Sonar System) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - ] | |
| Intuitive parking assist system (w/o Intelligent Clearance Sonar System) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - 07/2020] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Clearance warning ECU assembly | Refer to REMOVAL [05/2019 - ] | |
| "Blind Spot Monitor Unavailable" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Blind Spot Monitor System) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] |
| Blind spot monitor system | Refer to REMOVAL [09/2017 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Blind spot monitor sensor LH | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] | |
| "Blind Spot Monitor System Malfunction Visit Your Dealer" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Blind Spot Monitor System) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] |
| Blind spot monitor system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Blind spot monitor sensor LH | Refer to REMOVAL [09/2017 - ] | |
| "Moon Roof Open" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Sliding Roof System) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] |
| Sliding roof system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Main body ECU (multiplex network body ECU) | Refer to REMOVAL [05/2019 - ] | |
| "Window Open" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] |
| Power window control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Main body ECU (multiplex network body ECU) | Refer to REMOVAL [05/2019 - ] | |
| "Window or Moon Roof Open" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Sliding Roof System) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] |
| Power window control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] | |
| Sliding roof system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Main body ECU (multiplex network body ECU) | Refer to REMOVAL [05/2019 - ] | |
| "High Power Consumption Partial Limit On AC/Heater Operation" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] |
| Air conditioning system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Air conditioning amplifier assembly | Refer to REMOVAL [09/2017 - ] | |
| "Theft Sensor Turned Off" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] |
| Theft deterrent system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Main body ECU (multiplex network body ECU) | Refer to REMOVAL [05/2019 - ] | |
| "Theft Sensor Turned On" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] |
| Theft deterrent system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Main body ECU (multiplex network body ECU) | Refer to REMOVAL [05/2019 - ] | |
| Dead pixels on multi-information display | Perform Active Test [Meter Display 1] | Refer to DATA LIST / ACTIVE TEST [10/2014 - ] |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Multi-information display customize setting does not operate | Combination meter assembly | Refer to REMOVAL [09/2017 - ] |
| "ADJUSTING FORWARD CAMERA" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Dynamic radar cruise control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Forward recognition camera | Refer to REMOVAL [05/2019 - ] | |
| "CHECKING PCS BRAKE" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Pre-collision system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Forward recognition camera | Refer to REMOVAL [05/2019 - ] | |
| "WRITE ZERO-POINT OF STEERING ANGLE" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Intuitive parking assist system) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Intuitive parking assist system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Clearance warning ECU assembly | Refer to REMOVAL [05/2019 - ] | |
| "END OF ADJUSTMENT" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Intuitive parking assist system) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Intuitive parking assist system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Clearance warning ECU assembly | Refer to REMOVAL [05/2019 - ] | |
| "MEMORY ERROR" message is displayed when it should not be, not displayed when it should be, or not displayed correctly (w/ Intuitive parking assist system) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Intuitive parking assist system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Clearance warning ECU assembly | Refer to REMOVAL [05/2019 - ] | |
| "Headlight System Uninitialized. Visit Your Dealer." message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Lighting system (for Triple Beam Headlight) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] | |
| Lighting system (for Single Beam Headlight) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Headlight light control ECU sub-assembly LH | Refer to REMOVAL [09/2017 - ] | |
| "Press Brake Pedal" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Intuitive parking assist system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2017 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Clearance warning ECU assembly | Refer to REMOVAL [05/2019 - ] | |
| "Check Fuel Cap" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| SFI system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| ECM | Refer to REMOVAL [10/2014 - ] | |
| "Traction Battery Needs to be Protected. Shift into P to Restart." message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Hybrid control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Hybrid vehicle control ECU | Refer to REMOVAL [05/2019 - ] | |
| "Traction Battery Needs to be Protected. Refrain From the Use of N Position." message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Hybrid control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Hybrid vehicle control ECU | Refer to REMOVAL [05/2019 - ] | |
| "Engine Maintenance Required. Visit Your Dealer." message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| SFI system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| ECM | Refer to REMOVAL [10/2014 - ] | |
| "Radar Cruise Control Unavailable. See Owner's Manual." message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Dynamic radar cruise control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Forward recognition camera | Refer to REMOVAL [05/2019 - ] | |
| ECM | Refer to REMOVAL [10/2014 - ] | |
| "LTA Unavailable" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Lane tracing assist system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Forward recognition camera | Refer to REMOVAL [05/2019 - ] | |
| "Front Camera Unavailable. See Owner's Manual." message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Pre-collision system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Forward recognition camera | Refer to REMOVAL [05/2019 - ] | |
| "Braking Power Low. Visit Your Dealer." message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Electronically Controlled Brake System | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Brake booster with master cylinder assembly (skid control ECU) | Refer to REMOVAL [05/2019 - ] | |
| "Turn Lights Off" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Lighting system (for Triple Beam Headlight) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] | |
| Lighting system (for Single Beam Headlight) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Main body ECU (multiplex network body ECU) | Refer to REMOVAL [05/2019 - ] | |
| "Brake Hold Deactivated. Parking Brake Automatically Applied." message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Electronically Controlled Brake System | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Brake booster with master cylinder assembly (skid control ECU) | Refer to REMOVAL [05/2019 - ] | |
| "Acoustic Vehicle Alerting System Malfunction Visit Your Dealer" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | Harness or connector | - |
| Vehicle proximity notification system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - 07/2020] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Vehicle approaching speaker assembly | Refer to REMOVAL [10/2014 - 07/2020] | |
| "RSA malfunction. Visit Your Dealer." message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Road sign assist system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Forward recognition camera | Refer to REMOVAL [05/2019 - ] | |
| "Exhaust Filter Full. Visit Your Dealer." message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| SFI system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| ECM | Refer to REMOVAL [10/2014 - ] | |
| "Aux Battery Low. See Owner's Manual." message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Hybrid control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Hybrid vehicle control ECU | Refer to REMOVAL [05/2019 - ] | |
| "Exhaust Filter Full. See Owner's Manual." message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| SFI system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| ECM | Refer to REMOVAL [10/2014 - ] | |
| "Exhaust Filter Regeneration In Process" message is displayed when it should not be, not displayed when it should be, or not displayed correctly | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| SFI system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| ECM | Refer to REMOVAL [10/2014 - ] |
HINT:
*A: Items for consideration regarding ambient temperature display value
- The display value of the ambient temperature around the sensor changes due to the effects of heat radiated from the engine room and vehicle speed.
- Depending on the driving status, the ambient temperature of the air surrounding the vehicle and the displayed value are different and the speed at which the displayed value updates is delayed. However, this is not a malfunction. When the vehicle is stopped or being driven at a low speed, the value is not updated to a higher temperature in order to minimize the effects of the radiated heat from the engine on the auto air conditioning control. Since the same adjustment occurs while the vehicle is being driven at medium to high speeds, updating to a higher temperature is delayed. However, the value is updated to a lower temperature regardless of the vehicle speed.
BUZZER
| Symptom | Suspected Area | Link |
|---|---|---|
| All buzzers do not operate normally | Combination meter assembly | Refer to REMOVAL [09/2017 - ] |
| Shift reject buzzer does not operate | Hybrid control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Hybrid vehicle control ECU | Refer to REMOVAL [05/2019 - ] | |
| Engine coolant temperature buzzer does not operate | SFI system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| ECM | Refer to REMOVAL [10/2014 - ] | |
| Seat belt warning buzzer does not operate (Front seat belt warning light operates normally) | Check customize setting | Refer to CUSTOMIZE PARAMETERS [10/2014 - ] |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Engine immobiliser certification buzzer does not operate | Immobiliser system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Certification ECU (smart key ECU assembly) | Refer to REMOVAL [10/2014 - ] | |
| Smart access system with push-button start warning buzzer does not operate | Smart access system with push-button start (for Entry Function) | Refer to REMOVAL [05/2019 - ] |
| Smart access system with push-button start (for Start Function) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Certification ECU (smart key ECU assembly) | Refer to REMOVAL [05/2019 - ] | |
| Power switch operation while driving warning buzzer does not operate | Smart access system with push-button start (for Entry Function) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] |
| Smart access system with push-button start (for Start Function) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Certification ECU (smart key ECU assembly) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] | |
| Restart while driving notification buzzer does not operate | Smart access system with push-button start (for Entry Function) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] |
| Smart access system with push-button start (for Start Function) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Certification ECU (smart key ECU assembly) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] | |
| Vehicle roll-away notification buzzer does not operate (Speedometer and tachometer operate normally) | Combination meter assembly | Refer to REMOVAL [09/2017 - ] |
| ECM | Refer to REMOVAL [10/2014 - ] | |
| Driving with any door opened warning buzzer does not operate (Open door warning light and speedometer operate normally) | Combination meter assembly | Refer to REMOVAL [09/2017 - ] |
| PKB-ON driving warning buzzer does not operate (Brake warning light and speedometer operate normally) | Combination meter assembly | Refer to REMOVAL [09/2017 - ] |
| EPS warning buzzer does not operate (Power steering system operates normally) | Combination meter assembly | Refer to REMOVAL [09/2017 - ] |
| Dynamic radar cruise control low speed cancel buzzer does not operate (w/ Dynamic Radar Cruise Control System) | Dynamic radar cruise control system | Refer to REMOVAL [10/2014 - ] |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Forward recognition camera | Refer to REMOVAL [10/2014 - ] | |
| Radar cruise low speed range preceding vehicle lost buzzer does not operate (w/ Dynamic Radar Cruise Control System) | Dynamic radar cruise control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Forward recognition camera | Refer to REMOVAL [05/2019 - ] | |
| Multi-information display warning buzzer does not operate | Combination meter assembly | Refer to REMOVAL [09/2017 - ] |
| Flasher buzzer does not operate (Turn indicator light normally) | Check customize setting | Refer to CUSTOMIZE PARAMETERS [10/2014 - ] |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Oil pressure warning buzzer does not operate | Engine oil pressure warning switch | Refer to INSPECTION [10/2014 - ] |
| Harness or connector | - | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Vehicle stability control sideways sliding warning buzzer does not operate | Electronically controlled brake system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Brake booster with master cylinder assembly (skid control ECU) | Refer to REMOVAL [05/2019 - ] | |
| Brake system low braking force warning buzzer does not operate | Electronically controlled brake system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Brake booster with master cylinder assembly (skid control ECU) | Refer to REMOVAL [05/2019 - ] | |
| Brake system temperature rise / active test buzzer does not operate | Electronically controlled brake system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Brake booster with master cylinder assembly (skid control ECU) | Refer to REMOVAL [05/2019 - ] | |
| Temperature warning/CRAWL cancel warning buzzer does not operate | Electronically controlled brake system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Brake booster with master cylinder assembly (skid control ECU) | Refer to REMOVAL [05/2019 - ] | |
| Hill-start assist control buzzer (Reset) malfunction | Electronically controlled brake system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Brake booster with master cylinder assembly (skid control ECU) | Refer to REMOVAL [05/2019 - ] | |
| Hill-start assist control buzzer (Set) malfunction | Electronically controlled brake system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Brake booster with master cylinder assembly (skid control ECU) | Refer to REMOVAL [05/2019 - ] | |
| Lane tracing assist cancel buzzer does not operate (w/ Lane tracing assist system) | Lane tracing assist system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Forward recognition camera | Refer to REMOVAL [05/2019 - ] | |
| Lane tracing assist warning buzzer does not operate (w/ Lane tracing assist system) | Lane tracing assist system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Forward recognition camera | Refer to REMOVAL [05/2019 - ] | |
| Lane tracing assist hands off steering wheel warning buzzer does not operate (w/ Lane tracing assist system) | Lane tracing assist system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Forward recognition camera | Refer to REMOVAL [05/2019 - ] | |
| Brake hold control unreleased warning buzzer does not operate | Electronically controlled brake system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Brake booster with master cylinder assembly (skid control ECU) | Refer to REMOVAL [05/2019 - ] | |
| EPB* cancel buzzer does not operate | Electrical parking brake system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Parking brake ECU assembly | Refer to REMOVAL [05/2019 - ] | |
| READY buzzer does not operate | Hybrid control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Hybrid vehicle control ECU | Refer to REMOVAL [05/2019 - ] | |
| EV reject buzzer does not operate | Hybrid control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Hybrid vehicle control ECU | Refer to REMOVAL [05/2019 - ] | |
| Shift to P position request buzzer does not operate | Hybrid control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Hybrid vehicle control ECU | Refer to REMOVAL [05/2019 - ] | |
| Depress the accelerator pedal with shift position N buzzer does not operate | Hybrid control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Hybrid vehicle control ECU | Refer to REMOVAL [05/2019 - ] | |
| Hybrid control system warning buzzer does not operate | Hybrid control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Hybrid vehicle control ECU | Refer to REMOVAL [05/2019 - ] | |
| HV battery low voltage buzzer does not operate | Hybrid control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Hybrid vehicle control ECU | Refer to REMOVAL [05/2019 - ] | |
| HV unit excessive heat notification buzzer does not operate | Hybrid control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Hybrid vehicle control ECU | Refer to REMOVAL [05/2019 - ] | |
| Tow prohibition buzzer does not operate | Hybrid control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Hybrid vehicle control ECU | Refer to REMOVAL [05/2019 - ] | |
| Accelerator hold warning buzzer does not operate | Hybrid control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Hybrid vehicle control ECU | Refer to REMOVAL [05/2019 - ] | |
| Power window / sliding roof warning buzzer malfunction | Power window control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] |
| Sliding roof system (w/ Sliding Roof System) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Main body ECU (multiplex network body ECU) | Refer to REMOVAL [05/2019 - ] | |
| Light reminder warning buzzer does not operate | Lighting system (for Triple Beam Headlight) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] |
| Lighting system (for Single Beam Headlight) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Main body ECU (multiplex network body ECU) | Refer to REMOVAL [05/2019 - ] |
OTHERS
| Symptom | Suspected Area | Link |
|---|---|---|
| DTCs display malfunction (Other systems operate normally) | Combination meter assembly | Refer to REMOVAL [09/2017 - ] |
| Operating light control rheostat does not change light brightness | Refer to "Operating Light Control Rheostat does not Change Light Brightness" | Refer to Operating Light Control Rheostat does not Change Light Brightness [10/2014 - ] |
| Meter illumination is always dark | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] |
| Lighting system (for Triple Beam Headlight) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] | |
| Lighting system (for Single Beam Headlight) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [05/2019 - ] | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Main body ECU (multiplex network body ECU) | Refer to REMOVAL [05/2019 - ] | |
| Operating ODO/TRIP switch does not change ODO/TRIP meter display | Refer to "Odo/Trip Switch Malfunction" | Refer to Odo/Trip Switch Malfunction [10/2014 - ] |
| Multi-information display does not change using steering pad switch assembly | Perform Active Test [Multi Switch (Up), Multi Switch (Down), Multi Switch (Menu), Multi Switch (Enter), Multi Switch (Right), Multi Switch (Left)] | Refer to DATA LIST / ACTIVE TEST [10/2014 - ] |
| Steering pad switch assembly | Refer to INSPECTION [09/2017 - ] | |
| Spiral with sensor cable sub-assembly | Refer to INSPECTION [09/2017 - ] | |
| Harness or connector | - | |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Cannot switch between tachometer and hybrid system indicator | Hybrid control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - ] |
| Combination meter assembly | Refer to REMOVAL [09/2017 - ] | |
| Hybrid vehicle control ECU | Refer to REMOVAL [05/2019 - ] |