DTC P0710-15: Transmission Fluid Temperature Sensor "A" Circuit Short to Battery or Open [10/2014 - ]: Procedure
- CHECK HARNESS AND CONNECTOR (ATF TEMPERATURE SENSOR CIRCUIT)
- Disconnect the ECM connector.
*a Front view of wire harness connector
(to ECM) - Measure the resistance according to the value(s) in the table below.
Standard Resistance
Tester Connection Condition Specified Condition C20-84 (THO1) - C20-83 (ETHO) Always 79 Ω to 156 kΩ C20-84 (THO1) - Other terminals Always 10 kΩ or higher C20-83 (ETHO) - Other terminals Always 10 kΩ or higher Result
Proceed to OK NG
Result:
OK
REPLACE ECM. Refer to REMOVAL [10/2014 - 05/2019] , or refer to REMOVAL [05/2019 - ]
Result:
NG
See step 2
- Disconnect the ECM connector.
- CHECK HARNESS AND CONNECTOR (WIRING HARNESS CONNECTOR - ECM)
- Disconnect the C21 wiring harness connector.
- Disconnect the C20 ECM connector.
- Measure the resistance according to the value(s) in the table below.
Standard Resistance
Tester Connection Condition Specified Condition C21-13 (OIL) - C20-84 (THO1) Always Below 1 Ω C21-12 (E2) - C20-83 (ETHO) Always Below 1 Ω C21-13 (OIL) or C20-84 (THO1) - Other terminals Always 10 kΩ or higher C21-12 (E2) or C20-83 (ETHO) - Other terminals Always 10 kΩ or higher Result
Proceed to OK NG
Result:
NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
Result:
OK
See step 3
- INSPECT TRANSMISSION WIRE (ATF TEMPERATURE SENSOR)
- Remove the wiring harness connector.
*a Component without harness connected
(Transmission Wire) - Measure the resistance according to the value(s) in the table below.
Standard Resistance
Tester Connection Condition Specified Condition A-18 (THO1) - A-17 (E2) Always 79 Ω to 156 kΩ A-18 (THO1) - Other terminals Always 10 kΩ or higher A-17 (E2) - Other terminals Always 10 kΩ or higher HINT:
If the resistance is out of the specified range at any of the ATF temperatures shown in the table below, the driveability of the vehicle may decrease.
ATF Temperature Specified Condition 10°C (50°F) 5 to 8 kΩ 25°C (77°F) 2.5 to 4.5 kΩ 110°C (230°F) 0.22 to 0.28 kΩ Result
Proceed to OK NG
Result:
OK
REPLACE WIRING HARNESS CONNECTOR. Refer to REMOVAL [10/2014 - 09/2015] , or refer to REMOVAL [09/2015 - 05/2019] , or refer to REMOVAL [05/2019 - ]
Result:
NG
See step 4
- Remove the wiring harness connector.
- INSPECT ATF TEMPERATURE SENSOR
- Disconnect the ATF temperature sensor connector.
*a Component without harness connected
(ATF Temperature Sensor Assembly)Refer to REMOVAL [10/2014 - ]
- Measure the resistance according to the value(s) in the table below.
Standard Resistance
Tester Connection Condition Specified Condition THO1 - E2 Always 79 Ω to 156 kΩ THO1 - Other terminals Always 10 kΩ or higher E2 - Other terminals Always 10 kΩ or higher HINT:
If the resistance is out of the specified range at any of the ATF temperatures shown in the table below, the driveability of the vehicle may decrease.
Resistance (Reference)
ATF Temperature Specified Condition 10°C (50°F) 5 to 8 kΩ 25°C (77°F) 2.5 to 4.5 kΩ 110°C (230°F) 0.22 to 0.28 kΩ Result
Proceed to OK NG
Result:
OK
REPLACE TRANSMISSION WIRE. Refer to REMOVAL [10/2014 - ]
Result:
NG
REPLACE ATF TEMPERATURE SENSOR (ATF TEMPERATURE SENSOR ASSEMBLY). Refer to REMOVAL [10/2014 - ]
- Disconnect the ATF temperature sensor connector.