LEMON Manuals: Even more car manuals for everyone
Home >> Lexus >> 2014 >> IS 350 Base, AWD >> Repair and Diagnosis >> Suspension >> Front Suspension >> Suspension System (Front) - Service Information (2 Of 2) >> FRONT LOWER SUSPENSION ARM (for 2WD) >> Installation [10/2016 - 10/2017] >> Procedure

Installation [10/2016 - 10/2017]: Procedure

  1. TEMPORARILY TIGHTEN LOWER NO. 2 ARM BRACKET SUB-ASSEMBLY 
    1. Temporarily tighten the lower No. 2 arm bracket sub-assembly to the front lower suspension arm assembly with the nut and washer.
  2. INSTALL FRONT LOWER BALL JOINT ASSEMBLY 

    See step  1

  3. TEMPORARILY TIGHTEN FRONT LOWER SUSPENSION ARM ASSEMBLY 
    1. Install the front lower suspension arm assembly and strut bar bracket reinforcement with the 3 bolts.

      Bolt (A) 

      Torque: 194 N.m (1978 kgf/cm, 143 ft.lbf) 

      Bolt (B) 

      Torque: 57 N.m (581 kgf/cm, 42 ft.lbf) 

      GTY629656Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Temporarily tighten the front lower suspension arm assembly with the bolt, nut and washer.
      NOTE:

      Insert the bolt from the front of the vehicle. Then install the washer and temporarily tighten the nut.

  4. INSTALL FRONT SUSPENSION CROSSMEMBER REINFORCEMENT 
    1. Install the front suspension crossmember reinforcement and the lower No. 2 arm bracket sub-assembly LH and lower No. 2 arm bracket sub-assembly RH to the front suspension crossmember sub-assembly with the 2 bolts and 2 nuts.

      Torque: 86 N.m (877 kgf/cm, 63 ft.lbf) 

  5. CONNECT FRONT LOWER BALL JOINT ASSEMBLY 
    1. Connect the front lower ball joint assembly to the steering knuckle with the 2 bolts.

      Torque: 120 N.m (1224 kgf/cm, 89 ft.lbf) 

  6. CONNECT TIE ROD ASSEMBLY 

    Refer to PROCEDURE - Step 4

  7. INSTALL FRONT STABILIZER LINK ASSEMBLY 

    See step  9

  8. TEMPORARILY TIGHTEN FRONT SHOCK ABSORBER WITH COIL SPRING 
    1. Temporarily tighten the front shock absorber with coil spring to the front lower suspension arm assembly with the bolt and nut.
      NOTE:
      • Insert the bolt from the rear of the vehicle.
      • Because the nut has its own stopper, do not turn the nut. Tighten the bolt with the nut secured.

      HINT: 

      Fully tighten the bolt after stabilizing the suspension.

  9. INSTALL SKID CONTROL SENSOR WIRE 

    Refer to PROCEDURE - Step 7

  10. STABILIZE SUSPENSION 

    Refer to PROCEDURE - Step 8

  11. FULLY TIGHTEN FRONT SHOCK ABSORBER WITH COIL SPRING 

    Refer to PROCEDURE - Step 9

  12. FULLY TIGHTEN FRONT LOWER SUSPENSION ARM ASSEMBLY 
    1. Fully tighten the bolt on the front of the front lower suspension arm assembly.

      Torque: 135 N.m (1377 kgf/cm, 100 ft.lbf) 

    2. Fully tighten the installation nut of the lower No. 2 arm bracket sub-assembly

      Torque: 113 N.m (1152 kgf/cm, 83 ft.lbf) 

  13. INSTALL FRONT SUSPENSION MEMBER BRACE 

    for 2GR-FSE: Refer to PROCEDURE - Step 102

    for 8AR-FTS: Refer to PROCEDURE - Step 77

  14. INSTALL ENGINE UNDER COVER 

    for 2GR-FSE: Refer to PROCEDURE - Step 105

    for 8AR-FTS: Refer to PROCEDURE - Step 78

  15. INSTALL FRONT WHEEL 

    Torque: 103 N.m (1050 kgf/cm, 76 ft.lbf) 

  16. INSPECT AND ADJUST FRONT WHEEL ALIGNMENT 

    Refer to ADJUSTMENT [10/2016 - 09/2020]