LEMON Manuals: Even more car manuals for everyone
Home >> Lexus >> 2014 >> IS 350 Base, AWD >> Repair and Diagnosis >> External Pages >> Different variant/trim >> Section 1 (Automatic Transmission System (Aa81E) - Service Information (1 Of 2)) >> Shift Lever >> Installation [08/2015 - 10/2017] >> Procedure

Installation [08/2015 - 10/2017]: Procedure

WARNING: This page is about a different variant/trim than selected.
  1. INSTALL TRANSMISSION FLOOR SHIFT ASSEMBLY 
    1. Temporarily install the transmission floor shift assembly to the body with the 4 bolts.
      NOTE:

      Do not pinch the wire harness.

      Fig 1: Transmission Floor Shift Assembly Tightening Sequence [08/2015 - 10/2017]
      GTY464405Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Fully tighten the 4 bolts in the order shown in the illustration.

      Torque: 8.3 N*m (85 kgf*cm, 73 in.*lbf) 

    3. Connect the shift lock control ECU connector.
      NOTE:

      Be sure to securely connect the shift lock control ECU connector.

    4. Connect the 4 clamps to the transmission floor shift assembly.
    5. Connect the transmission control switch connector.
      NOTE:

      Be sure to securely connect the transmission control switch connector.

  2. INSTALL NO. 1 CONSOLE BOX DUCT 
    1. Install the No. 1 console box duct with the 2 clips.
    2. Connect the 2 clamps to the No. 1 console box duct.
  3. INSTALL CONSOLE BOX ASSEMBLY 

    Refer to INSTALLATION [04/2013 - 10/2016] , or refer to INSTALLATION [10/2016 - 09/2020]

  4. INSTALL FLOOR SHIFT GEAR SHIFTING ROD SUB-ASSEMBLY 
    1. Turn the transmission control shaft lever RH counterclockwise until it stops, then turn it clockwise 2 notches.
      GTY462123Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *1 Transmission Control Shaft Lever RH
      *a P
      *b R
      *c N
    2. Move the shift lever to N.
    3. Temporarily install the floor shift gear shifting rod sub-assembly to the lever of the transmission floor shift assembly with the nut.
      GTY465206Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Lever
      Pushing the lever rearward
    4. Tighten the nut while lightly pushing the lever of the transmission floor shift assembly rearward.

      Torque: 12.8 N*m (131 kgf*cm, 9 ft.*lbf) 

      NOTE:

      Do not push the lever of the transmission floor shift assembly too hard.

  5. INSTALL FRONT NO. 1 FLOOR HEAT INSULATOR 

    Refer to PROCEDURE - Step 5

  6. INSTALL FRONT EXHAUST PIPE ASSEMBLY (for 2GR-FSE) 

    Refer to INSTALLATION [04/2013 - 10/2016] , or refer to INSTALLATION [10/2016 - 10/2017]

  7. INSTALL FRONT EXHAUST PIPE ASSEMBLY (for 8AR-FTS) 

    Refer to INSTALLATION [08/2015 - 10/2016] , or refer to INSTALLATION [10/2016 - 09/2020]

  8. INSPECT SHIFT LEVER POSITION 

    See step  1

  9. INSPECT FOR EXHAUST GAS LEAK (for 2GR-FSE) 

    Refer to PROCEDURE - Step 9 [04/2013 - 10/2016] , or refer to PROCEDURE - Step 9 [10/2016 - 10/2017]

  10. INSPECT FOR EXHAUST GAS LEAK (for 8AR-FTS) 

    Refer to PROCEDURE - Step 8 [08/2015 - 10/2016] , or refer to PROCEDURE - Step 8 [10/2016 - 09/2020]

scientia non olet · About LEMON Manuals