LEMON Manuals: Even more car manuals for everyone
Home >> Lexus >> 2014 >> IS 350 Base, AWD >> Repair and Diagnosis >> Engine Mechanical >> Mechanical >> Engine Mechanical System (2GR-FSE) - Service Information (1 Of 2) >> Rear Crankshaft Oil Seal >> Installation [04/2013 - 10/2017] >> Procedure

Installation [04/2013 - 10/2017]: Procedure

  1. INSTALL ENGINE REAR OIL SEAL 
    1. Clean the crankshaft and engine rear oil seal retainer.
    2. Apply MP grease to the lip of a new engine rear oil seal.
      NOTE:
      • Keep the lip free of foreign matter.
      • Do not allow MP grease to contact the dust seal section.
    3. Using SST and a hammer, tap in the engine rear oil seal until its surface is flush with the engine rear oil seal retainer edge.
      GTY465701Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Standard depth
      • SST: 09223-1503009950-70010 
        1. 09951-07150

      Standard depth

      -0.5 to 0.5 mm (-0.0197 to 0.0197 in.)

      NOTE:
      • Keep the lip free of foreign matter.
      • Do not tap in the engine rear oil seal at an angle.
      • Do not tap in the engine rear oil seal more than necessary.
      • Do not deform the engine rear oil seal.
      • Wipe off extra MP grease on the crankshaft.
  2. INSTALL DRIVE PLATE 
    1. Using SST, hold the crankshaft pulley.
      GTY469477Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      • SST: 09330-0002109213-70011 
        1. 09213-70020
    2. Clean the 8 bolts and 8 bolt holes.
    3. Install the front drive plate spacer.
      GTY460618Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *1 Pin Hole
      *2 Pin

      HINT: 

      Align the pin of the front drive plate spacer with the pin hole of the crankshaft.

    4. Install the drive plate and rear drive plate spacer onto the crankshaft.
      GTY459359Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *1 Drive Plate
      *2 Rear Drive Plate Spacer
      Transmission Side

      HINT: 

      Make sure the installation direction of the drive plate and the rear drive plate spacer.

    5. Apply a few drops of adhesive to 2 or 3 threads of the 8 bolt tips.
      GTY464547Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *1 Adhesive

      Adhesive

      Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent

      NOTE:

      Install the bolt within 3 minutes after applying adhesive.

    6. In several steps, uniformly tighten the 8 bolts in the sequence shown in the illustration.
      Fig 1: Drive Plate Tightening Sequence
      GTY461071Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      Torque: 83.5 N*m (851 kgf*cm, 62 ft.*lbf) 

      NOTE:

      Do not start the engine for at least an hour after installing the drive plate.

  3. INSPECT DRIVE PLATE (for 2WD) 

    Refer to PROCEDURE - Step 2 [04/2013 - 08/2015] , or refer to PROCEDURE - Step 2 [08/2015 - 10/2017]

  4. INSPECT DRIVE PLATE (for AWD) 

    Refer to PROCEDURE - Step 2 [04/2013 - 08/2015] , or refer to PROCEDURE - Step 2 [08/2015 - ]

  5. INSTALL AUTOMATIC TRANSMISSION ASSEMBLY (for 2WD) 

    Refer to INSTALLATION [04/2013 - 08/2015] , or refer to INSTALLATION [08/2015 - 10/2016] , or refer to INSTALLATION [10/2016 - ]

  6. INSTALL AUTOMATIC TRANSMISSION WITH TRANSFER ASSEMBLY (for AWD) 

    Refer to INSTALLATION [04/2013 - 08/2015] , or refer to INSTALLATION [08/2015 - ]

  7. INSPECT FOR OIL LEAK 

    Refer to PROCEDURE - Step 8 [04/2013 - 08/2015] , or refer to PROCEDURE - Step 8 [08/2015 - 10/2017]

scientia non olet · About LEMON Manuals