LEMON Manuals: Even more car manuals for everyone
Home >> Lexus >> 2014 >> IS 350 Base, AWD >> Repair and Diagnosis (Single Page) >> Accessories & Equipment >> Entertainment Systems >> Audio / Video System - Diagnostic Codes (1 Of 2) >> Audio And Visual System >> DTC B1323: Lost Communication with Haptic Device; DTC B1324: Lost Communication with Meter; DTC B1326: Lost Communication with Clock Device (Local-CAN) [09/2020 - ] >> Procedure

DTC B1323: Lost Communication with Haptic Device; DTC B1324: Lost Communication with Meter; DTC B1326: Lost Communication with Clock Device (Local-CAN) [09/2020 - ]: Procedure

  1. CHECK DTC 
    1. Check for DTCs and check that no DTCs are output.

      Body Electrical > Navigation System > Trouble Codes 

      Result

      Result Proceed to
      DTC B1323, B1324 and B1326 are not output A
      DTC B1323, B1324 and B1326 are output B
      DTC B1323 is output C
      DTC B1324 is output D
      DTC B1326 is output E

    Result: 

    A 

    USE SIMULATION METHOD TO CHECK. Refer to  HOW TO PROCEED WITH TROUBLESHOOTING [09/2020 - 11/2021]  , or refer to  HOW TO PROCEED WITH TROUBLESHOOTING [11/2021 - 09/2022]  , or refer to  HOW TO PROCEED WITH TROUBLESHOOTING [09/2022 - ] 

    Result: 

    C 

    See step  13

    Result: 

    D 

    See step  16

    Result: 

    E 

    See step  19

    Result: 

    B 

    See step  2

  2. CHECK LOCAL BUS 
    1. Disconnect the cable from the negative (-) battery terminal.
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      K169-1 - K169-12 Cable disconnected from negative (-) battery terminal 54 to 69 Ω

      Result

      Result Proceed to
      OK A
      NG (Below 54 Ω) B
      NG (70 Ω or higher) C

    Result: 

    A 

    USE SIMULATION METHOD TO CHECK. Refer to  HOW TO PROCEED WITH TROUBLESHOOTING [09/2020 - 11/2021]  , or refer to  HOW TO PROCEED WITH TROUBLESHOOTING [11/2021 - 09/2022]  , or refer to  HOW TO PROCEED WITH TROUBLESHOOTING [09/2022 - ] 

    Result: 

    C 

    See step  11

    Result: 

    B 

    See step  3

  3. CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - NO. 15 CAN JUNCTION CONNECTOR) 
    1. Disconnect the cable from the negative (-) battery terminal.
    2. Disconnect the K169 No. 15 CAN junction connector.
    3. Connect the K173 radio receiver assembly connector.
    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      K169-1 - K169-12 Cable disconnected from negative (-) battery terminal 108 to 132 Ω

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    See step  10

    Result: 

    OK 

    See step  4

  4. CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - NO. 15 CAN JUNCTION CONNECTOR) 
    1. Disconnect the cable from the negative (-) battery terminal.
    2. Disconnect the K169 No. 15 CAN junction connector.
    3. Connect the K4 combination meter assembly connector.
    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      K169-2 - K169-13 Cable disconnected from negative (-) battery terminal 200 Ω or higher

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    See step  9

    Result: 

    OK 

    See step  5

  5. CHECK HARNESS AND CONNECTOR (REMOTE TOUCH (REMOTE OPERATION CONTROLLER ASSEMBLY) - NO. 15 CAN JUNCTION CONNECTOR) 
    1. Disconnect the cable from the negative (-) battery terminal.
    2. Disconnect the K169 No. 15 CAN junction connector.
    3. Connect the K180 remote touch (remote operation controller assembly) connector.
    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      K169-3 - K169-14 Cable disconnected from negative (-) battery terminal 108 to 132 Ω

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    See step  8

    Result: 

    OK 

    See step  6

  6. CHECK HARNESS AND CONNECTOR (CLOCK ASSEMBLY - NO. 15 CAN JUNCTION CONNECTOR) 
    1. Disconnect the cable from the negative (-) battery terminal.
    2. Disconnect the K169 No. 15 CAN junction connector.
    3. Connect the K167 clock assembly connector.
    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      K169-4 - K169-15 Cable disconnected from negative (-) battery terminal 200 Ω or higher

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE NO. 15 CAN JUNCTION CONNECTOR 

    Result: 

    NG 

    See step  7

  7. CHECK HARNESS AND CONNECTOR (CLOCK ASSEMBLY - NO. 15 CAN JUNCTION CONNECTOR) 
    1. Disconnect the cable from the negative (-) battery terminal.
    2. Disconnect the K167 clock assembly connector.
    3. Connect the K169 No. 15 CAN junction connector.
    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      K167-5 (TX+1) - K167-6 (TX-1) Cable disconnected from negative (-) battery terminal 54 to 69 Ω

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE CLOCK ASSEMBLY. Refer to  REMOVAL [04/2013 - ] 

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

  8. CHECK HARNESS AND CONNECTOR (REMOTE TOUCH (REMOTE OPERATION CONTROLLER ASSEMBLY) - NO. 15 CAN JUNCTION CONNECTOR) 
    1. Disconnect the cable from the negative (-) battery terminal.
    2. Disconnect the K180 remote touch (remote operation controller assembly) connector.
    3. Connect the K169 No. 15 CAN junction connector.
    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      K180-9 (MO+) - K180-8 (MO-) Cable disconnected from negative (-) battery terminal 108 to 132 Ω

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE REMOTE TOUCH (REMOTE OPERATION CONTROLLER ASSEMBLY). Refer to  REMOVAL [09/2020 - ] 

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

  9. CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - NO. 15 CAN JUNCTION CONNECTOR) 
    1. Disconnect the cable from the negative (-) battery terminal.
    2. Disconnect the K4 combination meter assembly connector.
    3. Connect the K169 No. 15 CAN junction connector.
    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      K4-10 (MSCH) - K4-9 (MSCL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE COMBINATION METER ASSEMBLY. Refer to  REMOVAL [09/2020 - ] 

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

  10. CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - NO. 15 CAN JUNCTION CONNECTOR) 
    1. Disconnect the cable from the negative (-) battery terminal.
    2. Disconnect the K173 radio receiver assembly connector.
    3. Connect the K169 No. 15 CAN junction connector.
    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      K173-5 (CNH1) - K173-6 (CNL1) Cable disconnected from negative (-) battery terminal 108 to 132 Ω

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE RADIO RECEIVER ASSEMBLY. Refer to  REMOVAL [09/2020 - ] 

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

  11. CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - NO. 15 CAN JUNCTION CONNECTOR) 
    1. Disconnect the cable from the negative (-) battery terminal.
    2. Disconnect the K173 radio receiver assembly connector.
    3. Connect the K169 No. 15 CAN junction connector.
    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      K173-5 (CNH1) - K173-6 (CNL1) Cable disconnected from negative (-) battery terminal 108 to 132 Ω

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE RADIO RECEIVER ASSEMBLY. Refer to  REMOVAL [09/2020 - ] 

    Result: 

    NG 

    See step  12

  12. CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - NO. 15 CAN JUNCTION CONNECTOR) 
    1. Disconnect the cable from the negative (-) battery terminal.
    2. Disconnect the K169 No. 15 CAN junction connector.
    3. Connect the K173 radio receiver assembly connector.
    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      K169-1 - K169-12 Cable disconnected from negative (-) battery terminal 108 to 132 Ω

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE NO. 15 CAN JUNCTION CONNECTOR 

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

  13. CHECK HARNESS AND CONNECTOR (REMOTE TOUCH (REMOTE OPERATION CONTROLLER ASSEMBLY) POWER SOURCE) 
    1. Disconnect the K180 remote touch (remote operation controller assembly) connector.
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      K180-10 (GND) - Body ground Always Below 1 Ω
    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage

      Tester Connection Condition Specified Condition
      K180-1 (+B) - Body ground Always 11 to 14 V
      K180-6 (ACC) - Body ground Ignition switch ACC 11 to 14 V

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

    Result: 

    OK 

    See step  14

  14. CHECK HARNESS AND CONNECTOR (REMOTE TOUCH (REMOTE OPERATION CONTROLLER ASSEMBLY) - NO. 15 CAN JUNCTION CONNECTOR) 
    1. Disconnect the cable from the negative (-) battery terminal.
    2. Disconnect the K169 No. 15 CAN junction connector.
    3. Connect the K180 remote touch (remote operation controller assembly) connector.
    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      K169-3 - K169-14 Cable disconnected from negative (-) battery terminal 108 to 132 Ω

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE NO. 15 CAN JUNCTION CONNECTOR 

    Result: 

    NG 

    See step  15

  15. CHECK HARNESS AND CONNECTOR (REMOTE TOUCH (REMOTE OPERATION CONTROLLER ASSEMBLY) - NO. 15 CAN JUNCTION CONNECTOR) 
    1. Disconnect the cable from the negative (-) battery terminal.
    2. Disconnect the K180 remote touch (remote operation controller assembly) connector.
    3. Connect the K169 No. 15 CAN junction connector.
    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      K180-9 (MO+) - K180-8 (MO-) Cable disconnected from negative (-) battery terminal 108 to 132 Ω

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE REMOTE TOUCH (REMOTE OPERATION CONTROLLER ASSEMBLY). Refer to  REMOVAL [09/2020 - ] 

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

  16. CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY POWER SOURCE) 
    1. Disconnect the K3 combination meter assembly connector.
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      K3-31 (ES) - Body ground Always Below 1 Ω
    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage

      Tester Connection Condition Specified Condition
      K3-22 (B) - Body ground Always 11 to 14 V
      K3-21 (IG+) - Body ground Ignition switch ON 11 to 14 V

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

    Result: 

    OK 

    See step  17

  17. CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - NO. 15 CAN JUNCTION CONNECTOR) 
    1. Disconnect the cable from the negative (-) battery terminal.
    2. Disconnect the K169 No. 15 CAN junction connector.
    3. Connect the K3 combination meter assembly connector.
    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      K169-2 - K169-13 Cable disconnected from negative (-) battery terminal 200 Ω or higher

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE NO. 15 CAN JUNCTION CONNECTOR 

    Result: 

    NG 

    See step  18

  18. CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - NO. 15 CAN JUNCTION CONNECTOR) 
    1. Disconnect the cable from the negative (-) battery terminal.
    2. Disconnect the K4 combination meter assembly connector.
    3. Connect the K169 No. 15 CAN junction connector.
    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      K4-10 (MSCH) - K4-9 (MSCL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE COMBINATION METER ASSEMBLY. Refer to  REMOVAL [09/2020 - ] 

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

  19. CHECK HARNESS AND CONNECTOR (CLOCK ASSEMBLY POWER SOURCE) 
    1. Disconnect the K167 clock assembly connector.
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      K167-7 (E) - Body ground Always Below 1 Ω
    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage

      Tester Connection Condition Specified Condition
      K167-1 (B) - Body ground Always 11 to 14 V
      K167-2 (ACC) - Body ground Ignition switch ACC 11 to 14 V

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

    Result: 

    OK 

    See step  20

  20. CHECK HARNESS AND CONNECTOR (CLOCK ASSEMBLY - NO. 15 CAN JUNCTION CONNECTOR) 
    1. Disconnect the cable from the negative (-) battery terminal.
    2. Disconnect the K169 No. 15 CAN junction connector.
    3. Connect the K167 clock assembly connector.
    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      K169-4 - K169-15 Cable disconnected from negative (-) battery terminal 200 Ω or higher

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE NO. 15 CAN JUNCTION CONNECTOR 

    Result: 

    NG 

    See step  21

  21. CHECK HARNESS AND CONNECTOR (CLOCK ASSEMBLY - NO. 15 CAN JUNCTION CONNECTOR) 
    1. Disconnect the cable from the negative (-) battery terminal.
    2. Disconnect the K167 clock assembly connector.
    3. Connect the K169 No. 15 CAN junction connector.
    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      K167-5 (TX+1) - K167-6 (TX-1) Cable disconnected from negative (-) battery terminal 54 to 69 Ω

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE CLOCK ASSEMBLY. Refer to  REMOVAL [04/2013 - ] 

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

scientia non olet · About LEMON Manuals